g_free and g_object_unref are in form of `void (*)(gpointer)`, which
matches the GDestroyNotify signature. An explicit GDestroyNotify cast on
g_free and g_object_unref is thus not needed.
* Allow whitespaces prefixing the values row.
* Allow more than one \r\n between the title and the table header.
Reported-by: Colin Helliwell <colin.helliwell@ln-systems.com>
Better check for ^SWWAN support during the first time a bearer is going
to be created.
The enabling phase isn't the correct one because this logic is only run
whenever a modem is detected but not hotplugged (i.e. this step is to
'reset' the modem to generic runtime settings).
The PHS8 in QMI-mode doesn't support GPS location retrieval via QMI, so we will
fallback to use the AT-based setup and the TTY for reading NMEA traces.
The setup in Cinterion modems goes as follows:
AT+CNMI=<mode>[, <mt>[, <bm>[, <ds>[, <bfr>]]]]
For each field, several setups are available, so we could use a default value,
as we were doing until now (+CNMI=2,1,2,2,1).
BUT, not every Cinterion modem allows the same set of settings. For example, the
new PHS8 only allows '0' for the <ds> value:
AT+CNMI=?
+CNMI: (0,1,2),(0,1),(0,2),(0),(1)
So, instead of hardcoding the setup, try to find the best suitable one for each
modem. We'll parse the +CNMI=? test response to know which values are supported
during the messaging support check, which is run once during initialization.
When automatic mode (i.e. 2G+3G+none preferred) is selected, we need to
explicitly request it by giving the AT+COPS write command with values (i.e. not
just empty fields).
Powering off Cinterion modems is done with the AT^SMSO command. Once this
command is sent to the device, ModemManager still needs to wait to get an
unsolicited ^SHUTDOWN message from the modem, which is when the shutdown
is considered complete.
Newer Cinterion devices, though, don't seem to follow this rule and just
reply OK to AT^SMSO (i.e. no ^SHUTDOWN), but instead, they will remove the
tty ports.
We now have a single 'CurrentModes' property which contains both values in a
tuple with signature "(uu)".
Also, rename 'SetAllowedModes()' to 'SetCurrentModes()', and update the list of
arguments expected to have a single "(uu)" tuple.
Instead of letting the plugins specify a default storage to use, just look at
the supported ones and use the best one.
"MT is preferred over "ME" or "SM", as "MT=ME+SM"
There is no point in specifying a default 'mem1' memory storage, which is used
for reading/listing/deleting, as those are operations that need a specific
'mem1' set each time.
Also, there is no point in specifying separate default 'mem2' and 'mem3' memory
storages, specially because now we allow Sms.Store() to specify a storage.
So, we will now only have a 'default' memory storage, which is applicable for
both 'mem2' and 'mem3' (storing, sending from storage and deleting).
Different ports of the same modem may get handled by different drivers. We
therefore need to provide a list of drivers (new `Modem.Drivers' property with
signature 'as') instead of just one (removed `Modem.Driver' property with
signature 's').
$ sudo mmcli -m 0 | grep drivers
| drivers: 'qcserial, qmi_wwan'
Instead of the `_in_port()' variants, we'll provide more generic
`_full()' methods. These should be used either if we want to send commands
to a specific port, or if we want to use a specific user-provided GCancellable.
In addition to this user-provided GCancellable, we keep the internal modem-wide
one.
* mm_base_modem_peek_port_* () will return either a port object (no new
reference), or NULL if none available.
You would usually peek() a port if you're going to use it just in the current
method, as there is no way to that reference to get invalid (we're single
threaded).
* mm_base_modem_get_port_* () will return either NEW references to valid
port objects, or NULL if none available.
And, you would usually get() a port, whenever you want the port object to be
valid even out of the current method, for example when keeping it in the
context of an async operation.
Also, we need to consider that the primary AT port MAY BE NULL when you
peek() or get() it. This is due to the fact that we may be releasing ports
(due to device disconnection) in the middle of async operations.
