If the modem requires +COPS re-registration after setting bands or
modes, use the common logic provided by the 3GPP interface, which
already knows e.g. whether the registration was automatic or the
actual requested operator id in case of being manual.
This will also make the u-blox plugin use the common +COPS set command
implemented in the broadband modem object, which has the fallback to
use the MCCMNC encoded in the current charset if needed.
Also, make sure we enable/disable the voice related unsolicited events
in both primary and secondary ports, because it may happen that the
primary port is connected with PPP and we're using the secondary port
for control.
If load_current_bands_finish() returns a NULL GArray, we must set the
GError or otherwise the daemon will segfault when the caller
dereferences the GError:
current_bands = MM_IFACE_MODEM_GET_INTERFACE (self)->load_current_bands_finish (self, res, &error);
if (!current_bands) {
/* Errors when getting current bands won't be critical */
mm_warn ("couldn't load current Bands: '%s'", error->message);
g_error_free (error);
}
This may happen with an empty but balid +UACT response, e.g.:
AT+UACT?
+UACT: ,,,
OK
Or when it replies a full empty string:
AT+UACT?
OK
When configuring these modems with AT+UUSBCONF=2, i.e. CDC-ECM + 4x
CDC-ACM, they also enumerate with a different PID on the USB. We need to
adjust the udev rules for that case in order to ignore the non-AT ports.
Signed-off-by: Sven Schwermer <sven.schwermer@disruptive-technologies.com>
This patch fixes several invalid checks like this:
array[i] && i < G_N_ELEMENTS (array)
which should instead be:
i < G_N_ELEMENTS (array) && array[i]
to avoid an out-of-bounds access of the array.
Fixes: c1aa658802
We were filtering the 4G bands supported by the module when parsing
+UBANDSEL responses, e.g. so that we would not reply unsupported bands
for a given ubandsel value.
But we need the same filtering in 2G and 3G bands, because for example
some modules may support a specific 4G band with a given ubandsel
value, but NOT the associated 3G band. E.g. the TOBY-R200 supports
EUTRAN-4 but not UTRAN-4.
We cannot have the ubandsel value comparision inside the for(;;) stop
conditions, because that would mean the loop would stop whenever the
comparison fails. We want to look for a value, so we need to loop the
whole array and stop once we find it only.
When we're changing modes or bands, we only need to keep track of the
initial power state when CFUN=4/CFUN=1 based logic is used. When using
COPS, we do not need to track initial power state or recover it after
the operation.
Make mm_ublox_get_support_config() return FALSE only when GError is
set. And also, prepare a preload_support_config() method to be run
before using any information from the support configuration (i.e.
don't do it in load_supported_bands(), do it in load_current_bands()
or in set_current_bands().
If mm_ublox_get_supported_bands() and mm_ublox_get_support_config()
both failed, we would be completing the GTask twice. Fix it by
chaining both steps so that the second one is not run if the first one
is already failed.
The u-blox plugin was originally written to support the TOBY-L4 only.
This caused issues with mmcli reporting the correct supported and
current bands because the logic was based only for the TOBY-L4 and
the AT commands used in the implementaion are only supported by
a couple of modems.
There is now a hard-coded modem list that contains the supported bands
and the supported modes. A hard-coded list was chosen over a logic
based list because ublox modems only report the frequency of the bands
they support in the current mode they are in. For further justification,
the reported frequency could relate to multiple bands that are not all
supported by the modem, and not all the supported bands are always caught
depending on the mode the modem is in (e.g. 2G, 3G, 4G). The only
realiable way to retrieve the correct supported bands is to have the list
hard-coded. Based off of the modem, the code chooses whether it is
appropriate to issue +UACT or +UBANDSEL to retrieve the current bands list.
Additionally, the appropriate AT command of +CFUN=4 or +COPS=2 is chosen
to detach from the network when the mmcli --set-current-bands command is
issued. The new setup also adds a header file that contains the modem list.
This should make adding support for future additional modems easier as long
as future modems stick to the same AT command interface that is currently
supported by the plugin.
The SARA-U2xx and LISA-U20x require the PDP context to be activated via
+UCEDATA instead of +CGACT=1 when using the CDC-ECM USB profile.
Furthermore, they expect the DHCP discover packet from the TE while the
command is running, i.e. while the modem has not replied yet. In order
to achieve that, the bearer is marked as connected as soon as the
command is issued. This makes the NetworkManager start the DHCP process.
If the modem replies with an error, the bearer will be marked
disconnected later on.
Signed-off-by: Sven Schwermer <sven.schwermer@disruptive-technologies.com>
The TOBY-L2 allowed to skup the user/pass string fields when no
authentication was requested, but according to the AT command
reference, all the remaining u-blox modules do require these two
fields given always (e.g. just as empty strings).
As per this sequence in a TOBY-L4:
(ttyACM2): --> 'AT+UAUTHREQ=?<CR>'
(ttyACM2): <-- '<CR><LF>+UAUTHREQ: (1-4),(0-2),,<CR><LF><CR><LF>OK<CR><LF>'
(ttyACM2): --> 'AT+UAUTHREQ=1,0<CR>'
(ttyACM2): <-- '<CR><LF>+CME ERROR: 4<CR><LF>'
It should have been: AT+UAUTHREQ=1,0,"",""
When a new USB device is hotplugged, e.g. a USB<->RS232 converter that
exposes a single ttyUSB0, these udev events happen:
add /devices/pci0000:00/0000:00:14.0/usb2/2-1 (usb/usb-device)
add /devices/pci0000:00/0000:00:14.0/usb2/2-1/2-1:1.0 (usb/usb-interface)
add /devices/pci0000:00/0000:00:14.0/usb2/2-1/2-1:1.0/ttyUSB0 (usb-serial)
add /devices/pci0000:00/0000:00:14.0/usb2/2-1/2-1:1.0/ttyUSB0/tty/ttyUSB0 (tty)
bind /devices/pci0000:00/0000:00:14.0/usb2/2-1/2-1:1.0/ttyUSB0 (usb-serial)
bind /devices/pci0000:00/0000:00:14.0/usb2/2-1/2-1:1.0 (usb/usb-interface)
bind /devices/pci0000:00/0000:00:14.0/usb2/2-1 (usb/usb-device)
Our udev rules in MM only added tags in the 'add' events, and it looks
like the only ones 'persistent' after this sequence are those of the
last event happening on the specific path.
This meant that all TTY subsystem rules (e.g. ID_MM_CANDIDATE) would
be stored for later check (e.g. if ModemManager is started after these
rules have been applied), which was ok. "udevadm info -p ..." would
show these tags correctly always.
But this also meant that the 'bind' udev event happening for the USB
device didn't get any of our device-specific tags, and so we would be
missing them (e.g. ID_MM_DEVICE_MANUAL_SCAN_ONLY) if MM is started
after the last event has happened. "udevadm info -p ..." would
not show these tags.
Modify all our rules to also run at the 'bind' events.
See, for context:
https://github.com/systemd/systemd/issues/8221
The quick AT probe procedure is only meaningful to avoid waiting the
+READY URC delay. If there is no such delay configured, we shouldn't
run the quick AT probe (as a failure in the AT probe may also
trigger a +READY URC delay).
Just read the udev tag value early and complete the task if the delay
is not configured.
Added reading the ID_MM_UBLOX_PORT_READY_DELAY udev flag value and using
it as an init delay when a value is set.
The 20 second delay for the TOBY-L4 +READ URC has been reimplemented
using the new ID_MM_UBLOX_PORT_READY_DELAY udev value.
For the TOBY-R2, LISA-R2, and LARA-R2, the only valid AT ports are
ttyACM0, ttyACM1, and ttyACM2. All other ttyACM ports cause MM to
wait 20-30 seconds probing the port on startup.
Ignoring the non-AT ttyACM ports allows MM to not wait 20-30 seconds
probing and therefore startup much faster with these modems.
Keeps build with GCC 8 happy.
mm-base-call.c:758:18: warning: variable 'response' set but not used [-Wunused-but-set-variable]
mm-base-call.c:822:18: warning: variable 'response' set but not used [-Wunused-but-set-variable]
mm-base-sms.c:908:18: warning: variable 'response' set but not used [-Wunused-but-set-variable]
mm-sms-list.c:331:25: warning: variable 'ctx' set but not used [-Wunused-but-set-variable]
mm-iface-modem-messaging.c:1210:21: warning: variable 'storage_ctx' set but not used [-Wunused-but-set-variable]
huawei/mm-plugin-huawei.c:183:18: warning: variable 'response' set but not used [-Wunused-but-set-variable]
ublox/mm-plugin-ublox.c:161:24: warning: variable 'response' set but not used [-Wunused-but-set-variable]
ublox/mm-plugin-ublox.c:159:24: warning: variable 'ctx' set but not used [-Wunused-but-set-variable]
icera/mm-modem-helpers-icera.c:218:25: warning: variable 'first_free' set but not used [-Wunused-but-set-variable]
novatel/mm-common-novatel.c:50:18: warning: variable 'response' set but not used [-Wunused-but-set-variable]
The 'any' mode refers to the mode which includes most access
technologies and where none of them is preferred.
Fix the logic so that all combinations with one technology preferred
over the others are ignored, instead of the other way around.
Fixes assertion with the 4G-only LARA R204.
ModemManager[424]: <debug> [-192499452.090358] (ttyACM0): --> 'AT+URAT=?<CR>'
ModemManager[424]: <debug> [-192499452.092150] (ttyACM0): <-- '<CR><LF>+URAT: (3)<CR><LF><CR><LF>OK<CR><LF>'
**
ERROR:ublox/mm-modem-helpers-ublox.c:817:mm_ublox_get_modem_mode_any: assertion failed: (any != MM_MODEM_MODE_NONE)
Reported-by: Matthew Starr <mstarr@hedonline.com>
