Decouple from a specific initrd generator (dracut) the systemd services that
provide networking in the initrd using NM, thus allowing other systemd-based
initrd generators to take advantage of it.
These new services are:
- `NetworkManager-config-initrd.service`: it starts very early at boot, parses
the kernel command line using `nm-initrd-generator` and sets the
`/run/NetworkManager/initrd/neednet` flag to activate the other initrd services,
and also sets the hostname if needed.
- `NetworkManager-initrd.service`: it basically does the same job as the
`NetworkManager.service`, but in the initrd.
- `NetworkManager-wait-online-initrd.service`: ordered before
`network-online.target`, it will allow other services that require networking to
delay their start until NM has finished.
Recent gettext version can extract and merge back strings from and to
various file formats, no need for intltool anymore.
https://wiki.gnome.org/Initiatives/GnomeGoals/GettextMigrationhttps://gitlab.freedesktop.org/NetworkManager/NetworkManager/issues/133https://github.com/NetworkManager/NetworkManager/pull/303https://gitlab.freedesktop.org/NetworkManager/NetworkManager/-/merge_requests/96
Clarification about the use of AM_GNU_GETTEXT_REQUIRE_VERSION:
In configure.ac, specify the minimum gettext version we require, rather
than the exact one. This fixes a situation where the autoconf macros
used for gettext will be the latest available on the system (for
example, 0.20); but the copied-in Makefile.in.in will be for the exact
version specified in configure.ac (in this case, 0.19).
In that situation, the gettext build rules will error out at `make` time
with the message:
*** error: gettext infrastructure mismatch: using a Makefile.in.in
from gettext version 0.19 but the autoconf macros are from gettext
version 0.20
Avoid that by specifying a minimum version dependency rather than an
exact one. This should not cause problems as we haven’t committed any
generated or external gettext files into git, so each developer will end
up regenerating the build system for their system’s version of gettext,
as expected.
See the subsection of
https://www.gnu.org/software/gettext/manual/html_node/Version-Control-Issues.html
for more information.
Note that autoreconf currently doesn’t recognise
AM_GNU_GETTEXT_REQUIRE_VERSION, so we must continue also using
AM_GNU_GETTEXT_VERSION. autopoint will ignore the latter if the former
is present. See
https://lists.gnu.org/archive/html/autoconf-patches/2015-10/msg00000.html.
[lkundrak@v3.sk: Fixed the meson build, adjusted autogen.sh:
droped "|| exit 1", dropped call to aclocal,
dropped --copy from gtkdocize.]
NetworkManager runs as root and has lots of capabilities.
We want to reduce the attach surface by dropping capabilities,
but there is a genuine need to do certain things.
For example, we currently require dac_override capability, to open
the unix socket of ovsdb. Most users wouldn't use OVS, so we should
find a way to not require that dac_override capability. The solution
is to have a separate, D-Bus activate service (nm-sudo), which
has the capability to open and provide the file descriptor.
For authentication, we only rely on D-Bus. We watch the name owner
of NetworkManager, and only accept requests from that service. We trust
D-Bus to get it right a request from that name owner is really coming
from NetworkManager. If we couldn't trust that, how could PolicyKit
or any authentication via D-Bus work? For testing, the user can set
NM_SUDO_NO_AUTH_FOR_TESTING=1.
https://bugzilla.redhat.com/show_bug.cgi?id=1921826
Install a NM-specific firewalld zone to be used for interfaces that
are used for connection sharing. The zone blocks all traffic to the
local machine except some protocols (DHCP, DNS and ICMP) and allows
all forwarded traffic.
We don't need such data duplicated. The build setup should
have only one configuration_data() for patching such values.
Now we only have one global, immutable data_conf dictionary with
configuration values. Note that none of the users of data_conf uses all
entries, but as the entries are basically only dependent on the
meson/configure option and valid for the entire project, this simplifies
to handling.
Some variables belong to variables in their correspondent pkg-config
file.
These variables have been renamed to `dependency_variable` to
reflect the dependency and variables from pkg-config files they are
related to.
Some of these has also been fixed to use paths relative to
installation prefix.
Functions derived from generators as `configure_file`,
`custom_target` and `i18n.merge_file` can use placeholders like
`@BASENAME@` that removes the extension from the input filename
string.
The output string has been replaced by this placeholder that
allows in some cases the use of less variables.
WARNING: Project targetting '>= 0.44.0' but tried to use feature
introduced in '0.50.0': install arg in configure_file
From the documentation:
"install (added 0.50.0) When true, this generated file is installed
during the install step, and install_dir must be set and not
empty. When false, this generated file is not installed regardless of
the value of install_dir. When omitted it defaults to true when
install_dir is set and not empty, false otherwise."
The parameter can be omitted because install_dir is set.
https://gitlab.freedesktop.org/NetworkManager/NetworkManager/issues/216
If the NetworkManager daemon has been stopped manually we don't want it
to be autostarted by a client request.
[lkundrak@v3.sk: The auto-activation is probably more surprising than useful.
Services that need NetworkManager API should depend on NetworkManager service
directly.
I have no idea what purpose does the D-Bus service file serve nowadays,
but it looks rather hacky (really, activating /bin/false) and the comment
in it suggests that the autoactivating behavior was not intended anyway.
Debian has been shipping this for quite some time and no complains have been
heard.]
https://github.com/NetworkManager/NetworkManager/pull/230
Load the thunderbolt-net module if we see a host-to-host connection
and configure the resulting ethernet connection automatically to be
a link-local only one. The latter is done by setting a new udev
property "NM_AUTO_DEFAULT_LINK_LOCAL_ONLY" which is picked up when
we configure the connection for the device.
https://github.com/NetworkManager/NetworkManager/pull/97
