95 lines
3.6 KiB
Nix
95 lines
3.6 KiB
Nix
# this file originates from ‘nixos-generate-config’
|
||
# but has been heavily modified
|
||
{ pkgs, ... }:
|
||
|
||
{
|
||
# enables non-free firmware
|
||
hardware.enableRedistributableFirmware = true;
|
||
|
||
# i changed this becuse linux 5.10 didn't have rpi-400 device tree blob.
|
||
# nixos-22.05 linux 5.15 DOES have these now.
|
||
# it should be possible to remove this if desired, but i'm not sure how the rpi-specific kernel differs.
|
||
# see: https://github.com/raspberrypi/linux
|
||
boot.kernelPackages = pkgs.linuxPackages_rpi4;
|
||
|
||
# NixOS defaults to grub: we don't want that.
|
||
boot.loader.grub.enable = false;
|
||
# raspberryPi boot loader creates extlinux.conf.
|
||
# otherwise, enable the generic-extlinux-compatible loader below.
|
||
# note: THESE ARE MUTUALLY EXCLUSIVE. generic-extlinux-compatible causes uboot to not be built
|
||
# boot.loader.generic-extlinux-compatible.enable = true;
|
||
boot.loader.raspberryPi.enable = true;
|
||
boot.loader.raspberryPi.uboot.enable = true;
|
||
boot.loader.raspberryPi.version = 4;
|
||
|
||
boot.initrd.availableKernelModules = [
|
||
"bcm2711_thermal"
|
||
"bcm_phy_lib"
|
||
"brcmfmac"
|
||
"brcmutil"
|
||
"broadcom"
|
||
"clk_raspberrypi"
|
||
"drm" # Direct Render Manager
|
||
"enclosure" # SCSI ?
|
||
"fuse"
|
||
"mdio_bcm_unimac"
|
||
"pcie_brcmstb"
|
||
"raspberrypi_cpufreq"
|
||
"raspberrypi_hwmon"
|
||
"ses" # SCSI Enclosure Services
|
||
"uas" # USB attached storage
|
||
"uio" # userspace IO
|
||
"uio_pdrv_genirq"
|
||
"xhci_pci"
|
||
"xhci_pci_renesas"
|
||
];
|
||
# boot.initrd.compressor = "gzip"; # defaults to zstd
|
||
# hack in the `boot.shell_on_fail` arg since it doesn't seem to work otherwise
|
||
boot.initrd.preFailCommands = "allowShell=1";
|
||
# default: 4 (warn). 7 is debug
|
||
boot.consoleLogLevel = 7;
|
||
# boot.kernelParams = [
|
||
# "boot.shell_on_fail"
|
||
# # "boot.trace"
|
||
# # "systemd.log_level=debug"
|
||
# # "systemd.log_target=console"
|
||
# ];
|
||
|
||
# ondemand power scaling keeps the cpu at low frequency when idle, and sets to max frequency
|
||
# when load is detected. (v.s. the "performance" default, which always uses the max frequency)
|
||
powerManagement.cpuFreqGovernor = "ondemand";
|
||
|
||
# XXX colin: this allows one to `systemctl halt` and then not remove power until the HDD has spun down.
|
||
# however, it doesn't work with reboot because systemd will spin the drive up again to read its reboot bin.
|
||
# a better solution would be to put the drive behind a powered USB hub (or get a SSD).
|
||
# systemd.services.diskguard = {
|
||
# description = "Safely power off spinning media";
|
||
# before = [ "shutdown.target" ];
|
||
# wantedBy = [ "sysinit.target" ];
|
||
# # old (creates dep loop, but works)
|
||
# # before = [ "systemd-remount-fs.service" "shutdown.target" ];
|
||
# # wantedBy = [ "systemd-remount-fs.service" ];
|
||
# serviceConfig = {
|
||
# Type = "oneshot";
|
||
# RemainAfterExit = true;
|
||
# ExecStart = "${pkgs.coreutils}/bin/true";
|
||
# ExecStop = with pkgs; writeScript "diskguard" ''
|
||
# #!${bash}/bin/bash
|
||
# if ${procps}/bin/pgrep nixos-rebuild ;
|
||
# then
|
||
# exit 0 # don't halt drives unless we're actually shutting down. maybe better way to do this (check script args?)
|
||
# fi
|
||
# # ${coreutils}/bin/sync
|
||
# # ${util-linux}/bin/mount -o remount,ro /nix/store
|
||
# # ${util-linux}/bin/mount -o remount,ro /
|
||
# # -S 1 retracts the spindle after 5 seconds of idle
|
||
# # -B 1 spins down the drive after <vendor specific duration>
|
||
# ${hdparm}/sbin/hdparm -S 1 -B 1 /dev/sda
|
||
# # TODO: monitor smartmonctl until disk is idle? or try hdparm -Y
|
||
# # ${coreutils}/bin/sleep 20
|
||
# # exec ${util-linux}/bin/umount --all -t ext4,vfat,ext2
|
||
# '';
|
||
# };
|
||
# };
|
||
}
|