Merge branch '2022-03-25-Kconfig-migrations' into next

- Merge a number of Kconfig migration patches

README

@@ -994,10 +994,6 @@ The following options need to be configured:
 		display); also select one of the supported displays
 		by defining one of these:
 
-		CONFIG_ATMEL_LCD:
-
-			HITACHI TX09D70VM1CCA, 3.5", 240x320.
-
 		CONFIG_NEC_NL6448AC33:
 
 			NEC NL6448AC33-18. Active, color, single scan.
@@ -1075,13 +1071,6 @@ The following options need to be configured:
 
 		The clock frequency of the MII bus
 
-		CONFIG_PHY_RESET_DELAY
-
-		Some PHY like Intel LXT971A need extra delay after
-		reset before any MII register access is possible.
-		For such PHY, set this option to the usec delay
-		required. (minimum 300usec for LXT971A)
-
 		CONFIG_PHY_CMD_DELAY (ppc4xx)
 
 		Some PHY like Intel LXT971A need extra delay after
@@ -1612,26 +1601,6 @@ The following options need to be configured:
 		this is instead controlled by the value of
 		/config/load-environment.
 
-- TFTP Fixed UDP Port:
-		CONFIG_TFTP_PORT
-
-		If this is defined, the environment variable tftpsrcp
-		is used to supply the TFTP UDP source port value.
-		If tftpsrcp isn't defined, the normal pseudo-random port
-		number generator is used.
-
-		Also, the environment variable tftpdstp is used to supply
-		the TFTP UDP destination port value.  If tftpdstp isn't
-		defined, the normal port 69 is used.
-
-		The purpose for tftpsrcp is to allow a TFTP server to
-		blindly start the TFTP transfer using the pre-configured
-		target IP address and UDP port. This has the effect of
-		"punching through" the (Windows XP) firewall, allowing
-		the remainder of the TFTP transfer to proceed normally.
-		A better solution is to properly configure the firewall,
-		but sometimes that is not allowed.
-
 		CONFIG_STANDALONE_LOAD_ADDR
 
 		This option defines a board specific value for the
@@ -2129,14 +2098,6 @@ Configuration Settings:
 		while unprotecting/erasing/programming. Please only enable
 		this option if you really know what you are doing.
 
-- CONFIG_SYS_RX_ETH_BUFFER:
-		Defines the number of Ethernet receive buffers. On some
-		Ethernet controllers it is recommended to set this value
-		to 8 or even higher (EEPRO100 or 405 EMAC), since all
-		buffers can be full shortly after enabling the interface
-		on high Ethernet traffic.
-		Defaults to 4 if not defined.
-
 - CONFIG_ENV_MAX_ENTRIES
 
 	Maximum number of entries in the hash table that is used
@@ -2234,12 +2195,6 @@ Note: once the monitor has been relocated, then it will complain if
 the default environment is used; a new CRC is computed as soon as you
 use the "saveenv" command to store a valid environment.
 
-- CONFIG_SYS_FAULT_ECHO_LINK_DOWN:
-		Echo the inverted Ethernet link state to the fault LED.
-
-		Note: If this option is active, then CONFIG_SYS_FAULT_MII_ADDR
-		      also needs to be defined.
-
 - CONFIG_SYS_FAULT_MII_ADDR:
 		MII address of the PHY to check for the Ethernet link state.
 

arch/arm/include/asm/arch-bcmcygnus/configs.h

@@ -19,7 +19,4 @@
 #define CONFIG_SYS_NS16550_CLK_DIV	54
 #define CONFIG_SYS_NS16550_COM3		0x18023000
 
-/* Ethernet */
-#define CONFIG_PHY_RESET_DELAY 10000 /* PHY reset delay in us*/
-
 #endif /* __ARCH_CONFIGS_H */

arch/arm/mach-at91/Kconfig

@@ -81,6 +81,7 @@ config TARGET_ETHERNUT5
 config TARGET_SNAPPER9260
 	bool "Support snapper9260"
 	select AT91SAM9260
+	select AT91_WANTS_COMMON_PHY
 	select DM
 	select DM_GPIO
 	select DM_SERIAL
@@ -89,6 +90,7 @@ config TARGET_SNAPPER9260
 config TARGET_GURNARD
 	bool "Support gurnard"
 	select AT91SAM9G45
+	select AT91_WANTS_COMMON_PHY
 	select BOARD_LATE_INIT
 	select DM
 	select DM_ETH
@@ -115,6 +117,7 @@ config TARGET_AT91SAM9263EK
 config TARGET_USB_A9263
 	bool "Caloa USB A9260 board"
 	select AT91SAM9263
+	select AT91_WANTS_COMMON_PHY
 
 config TARGET_PM9263
 	bool "Ronetix pm9263 board"
@@ -250,6 +253,7 @@ config TARGET_MEESC
 config TARGET_CORVUS
 	bool "Support corvus"
 	select AT91SAM9M10G45
+	select AT91_WANTS_COMMON_PHY
 	select DM
 	select DM_ETH
 	select DM_GPIO
@@ -267,6 +271,7 @@ config TARGET_SAMA7G5EK
 config TARGET_TAURUS
 	bool "Support taurus"
 	select AT91SAM9G20
+	select AT91_WANTS_COMMON_PHY
 	select DM
 	select DM_ETH
 	select DM_GPIO
@@ -279,6 +284,7 @@ config TARGET_TAURUS
 config TARGET_SMARTWEB
 	bool "Support smartweb"
 	select AT91SAM9260
+	select AT91_WANTS_COMMON_PHY
 	select DM
 	select DM_ETH
 	select DM_GPIO
@@ -318,6 +324,9 @@ config AT91_GPIO_PULLUP
 config ATMEL_LEGACY
 	bool "Legacy GPIO support"
 
+config AT91_WANTS_COMMON_PHY
+	bool
+
 source "board/atmel/at91sam9260ek/Kconfig"
 source "board/atmel/at91sam9261ek/Kconfig"
 source "board/atmel/at91sam9263ek/Kconfig"

arch/arm/mach-kirkwood/include/mach/config.h

@@ -45,14 +45,6 @@
 #define NAND_ALLOW_ERASE_ALL		1
 #endif
 
-/*
- * Ethernet Driver configuration
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN	/* detect link using phy */
-#define CONFIG_RESET_PHY_R	/* use reset_phy() to init mv8831116 PHY */
-#endif /* CONFIG_CMD_NET */
-
 /*
  * IDE Support on SATA ports
  */

arch/powerpc/cpu/mpc85xx/Kconfig

@@ -523,6 +523,7 @@ config ARCH_P2020
 
 config ARCH_P2041
 	bool
+	select BACKSIDE_L2_CACHE
 	select E500MC
 	select FSL_LAW
 	select SYS_CACHE_SHIFT_6
@@ -548,6 +549,7 @@ config ARCH_P2041
 
 config ARCH_P3041
 	bool
+	select BACKSIDE_L2_CACHE
 	select E500MC
 	select FSL_LAW
 	select SYS_CACHE_SHIFT_6
@@ -578,6 +580,7 @@ config ARCH_P3041
 
 config ARCH_P4080
 	bool
+	select BACKSIDE_L2_CACHE
 	select E500MC
 	select FSL_LAW
 	select SYS_CACHE_SHIFT_6
@@ -617,6 +620,7 @@ config ARCH_P4080
 
 config ARCH_P5040
 	bool
+	select BACKSIDE_L2_CACHE
 	select E500MC
 	select FSL_LAW
 	select SYS_CACHE_SHIFT_6
@@ -647,6 +651,7 @@ config ARCH_QEMU_E500
 
 config ARCH_T1024
 	bool
+	select BACKSIDE_L2_CACHE
 	select E500MC
 	select FSL_LAW
 	select SYS_CACHE_SHIFT_6
@@ -670,6 +675,7 @@ config ARCH_T1024
 
 config ARCH_T1040
 	bool
+	select BACKSIDE_L2_CACHE
 	select E500MC
 	select FSL_LAW
 	select SYS_CACHE_SHIFT_6
@@ -693,6 +699,7 @@ config ARCH_T1040
 
 config ARCH_T1042
 	bool
+	select BACKSIDE_L2_CACHE
 	select E500MC
 	select FSL_LAW
 	select SYS_CACHE_SHIFT_6
@@ -1108,6 +1115,9 @@ config SYS_NUM_TLBCAMS
 		Number of TLB CAM entries for Book-E chips. 64 for E500MC,
 		16 for other E500 SoCs.
 
+config BACKSIDE_L2_CACHE
+	bool
+
 config SYS_PPC64
 	bool
 

board/bluewater/gurnard/Kconfig

@@ -1,5 +1,8 @@
 if TARGET_GURNARD
 
+config GURNARD_SPLASH
+	def_bool y
+
 config SYS_BOARD
 	default "gurnard"
 

board/ronetix/pm9263/Kconfig

@@ -1,5 +1,8 @@
 if TARGET_PM9263
 
+config LCD_IN_PSRAM
+	def_bool y
+
 config SYS_BOARD
 	default "pm9263"
 

board/siemens/corvus/Kconfig

@@ -1,5 +1,8 @@
 if TARGET_CORVUS
 
+config AT91_LED
+	def_bool y
+
 config SYS_BOARD
 	default "corvus"
 

cmd/Kconfig

@@ -1658,6 +1658,10 @@ config CMD_MII
 	  to management parameters and services.
 	  The interface is referred to as the MII management interface.
 
+config MII_INIT
+	bool "Call mii_init() in the mii command"
+	depends on CMD_MII && (MPC8XX_FEC || FSLDMAFE || MCFFEC)
+
 config CMD_MDIO
 	bool "mdio"
 	depends on PHYLIB

common/Kconfig

@@ -611,6 +611,12 @@ config PCI_INIT_R
 	  case of DM PCI-based Ethernet devices, which will not be detected
 	  without having the enumeration performed earlier.
 
+config RESET_PHY_R
+	bool "Reset ethernet PHY during init"
+	help
+	  Implement reset_phy() in board code if required to reset the ethernet
+	  PHY.
+
 endmenu
 
 endmenu		# Init options

common/lcd.c

@@ -90,54 +90,6 @@ static void lcd_stub_puts(struct stdio_dev *dev, const char *s)
 	lcd_puts(s);
 }
 
-/* Small utility to check that you got the colours right */
-#ifdef LCD_TEST_PATTERN
-
-#if LCD_BPP == LCD_COLOR8
-#define	N_BLK_VERT	2
-#define	N_BLK_HOR	3
-
-static int test_colors[N_BLK_HOR * N_BLK_VERT] = {
-	CONSOLE_COLOR_RED,	CONSOLE_COLOR_GREEN,	CONSOLE_COLOR_YELLOW,
-	CONSOLE_COLOR_BLUE,	CONSOLE_COLOR_MAGENTA,	CONSOLE_COLOR_CYAN,
-}; /*LCD_BPP == LCD_COLOR8 */
-
-#elif LCD_BPP == LCD_COLOR16
-#define	N_BLK_VERT	2
-#define	N_BLK_HOR	4
-
-static int test_colors[N_BLK_HOR * N_BLK_VERT] = {
-	CONSOLE_COLOR_RED,	CONSOLE_COLOR_GREEN,	CONSOLE_COLOR_YELLOW,	CONSOLE_COLOR_BLUE,
-	CONSOLE_COLOR_MAGENTA,	CONSOLE_COLOR_CYAN,	CONSOLE_COLOR_GREY,	CONSOLE_COLOR_WHITE,
-};
-#endif /*LCD_BPP == LCD_COLOR16 */
-
-static void test_pattern(void)
-{
-	ushort v_max  = panel_info.vl_row;
-	ushort h_max  = panel_info.vl_col;
-	ushort v_step = (v_max + N_BLK_VERT - 1) / N_BLK_VERT;
-	ushort h_step = (h_max + N_BLK_HOR  - 1) / N_BLK_HOR;
-	ushort v, h;
-#if LCD_BPP == LCD_COLOR8
-	uchar *pix = (uchar *)lcd_base;
-#elif LCD_BPP == LCD_COLOR16
-	ushort *pix = (ushort *)lcd_base;
-#endif
-
-	printf("[LCD] Test Pattern: %d x %d [%d x %d]\n",
-		h_max, v_max, h_step, v_step);
-
-	for (v = 0; v < v_max; ++v) {
-		uchar iy = v / v_step;
-		for (h = 0; h < h_max; ++h) {
-			uchar ix = N_BLK_HOR * iy + h / h_step;
-			*pix++ = test_colors[ix];
-		}
-	}
-}
-#endif /* LCD_TEST_PATTERN */
-
 /*
  * With most lcd drivers the line length is set up
  * by calculating it from panel_info parameters. Some
@@ -201,9 +153,6 @@ void lcd_clear(void)
 	bg_color = CONSOLE_COLOR_BLACK;
 #endif	/* CONFIG_SYS_WHITE_ON_BLACK */
 
-#ifdef	LCD_TEST_PATTERN
-	test_pattern();
-#else
 	/* set framebuffer to background color */
 #if (LCD_BPP != LCD_COLOR32)
 	memset((char *)lcd_base, bg_color, lcd_line_length * panel_info.vl_row);
@@ -215,7 +164,6 @@ void lcd_clear(void)
 	   i++) {
 		*ppix++ = bg_color;
 	}
-#endif
 #endif
 	/* setup text-console */
 	debug("[LCD] setting up console...\n");

common/miiphyutil.c

@@ -366,7 +366,7 @@ int miiphy_reset(const char *devname, unsigned char addr)
 		debug("PHY reset failed\n");
 		return -1;
 	}
-#ifdef CONFIG_PHY_RESET_DELAY
+#if CONFIG_PHY_RESET_DELAY > 0
 	udelay(CONFIG_PHY_RESET_DELAY);	/* Intel LXT971A needs this */
 #endif
 	/*

configs/10m50_defconfig

@@ -27,6 +27,8 @@ CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_ADDR=0xF4080000
 CONFIG_VERSION_VARIABLE=y
 CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
+CONFIG_SYS_RX_ETH_BUFFER=0
 CONFIG_ALTERA_PIO=y
 CONFIG_MISC=y
 CONFIG_ALTERA_SYSID=y

configs/3c120_defconfig

@@ -27,6 +27,8 @@ CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_ADDR=0xE2880000
 CONFIG_VERSION_VARIABLE=y
 CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
+CONFIG_SYS_RX_ETH_BUFFER=0
 CONFIG_ALTERA_PIO=y
 CONFIG_MISC=y
 CONFIG_ALTERA_SYSID=y

configs/M5208EVBE_defconfig

@@ -14,11 +14,14 @@ CONFIG_SYS_PROMPT="-> "
 CONFIG_CMD_IMLS=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_MII=y
+CONFIG_MII_INIT=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_CACHE=y
 CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_ADDR=0x2000
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
+CONFIG_SYS_RX_ETH_BUFFER=8
 CONFIG_UDP_CHECKSUM=y
 CONFIG_SYS_I2C_LEGACY=y
 CONFIG_SYS_I2C_FSL=y

configs/M5235EVB_Flash32_defconfig

@@ -20,6 +20,7 @@ CONFIG_CMD_PCI=y
 CONFIG_CMD_DHCP=y
 CONFIG_BOOTP_BOOTFILESIZE=y
 CONFIG_CMD_MII=y
+CONFIG_MII_INIT=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_CACHE=y
 CONFIG_ENV_IS_IN_FLASH=y
@@ -27,6 +28,8 @@ CONFIG_ENV_ADDR=0xFFE04000
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="u-boot.bin"
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
+CONFIG_SYS_RX_ETH_BUFFER=8
 CONFIG_SYS_I2C_LEGACY=y
 CONFIG_SYS_I2C_FSL=y
 CONFIG_SYS_FSL_I2C_OFFSET=0x300

configs/M5235EVB_defconfig

@@ -20,6 +20,7 @@ CONFIG_CMD_PCI=y
 CONFIG_CMD_DHCP=y
 CONFIG_BOOTP_BOOTFILESIZE=y
 CONFIG_CMD_MII=y
+CONFIG_MII_INIT=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_CACHE=y
 CONFIG_ENV_IS_IN_FLASH=y
@@ -27,6 +28,8 @@ CONFIG_ENV_ADDR=0xFFE04000
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="u-boot.bin"
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
+CONFIG_SYS_RX_ETH_BUFFER=8
 CONFIG_SYS_I2C_LEGACY=y
 CONFIG_SYS_I2C_FSL=y
 CONFIG_SYS_FSL_I2C_OFFSET=0x300

configs/M5272C3_defconfig

@@ -17,10 +17,13 @@ CONFIG_CMD_IMLS=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_BOOTP_BOOTFILESIZE=y
 CONFIG_CMD_MII=y
+CONFIG_MII_INIT=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_CACHE=y
 CONFIG_ENV_ADDR=0xFFE04000
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
+CONFIG_SYS_RX_ETH_BUFFER=8
 CONFIG_SYS_BR0_PRELIM_BOOL=y
 CONFIG_SYS_BR0_PRELIM=0xFFE00201
 CONFIG_SYS_OR0_PRELIM=0xFFE00014

configs/M5275EVB_defconfig

@@ -21,10 +21,13 @@ CONFIG_CMD_I2C=y
 CONFIG_CMD_DHCP=y
 CONFIG_BOOTP_BOOTFILESIZE=y
 CONFIG_CMD_MII=y
+CONFIG_MII_INIT=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_CACHE=y
 CONFIG_ENV_ADDR=0xFFE04000
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
+CONFIG_SYS_RX_ETH_BUFFER=8
 CONFIG_SYS_I2C_LEGACY=y
 CONFIG_SYS_I2C_FSL=y
 CONFIG_SYS_FSL_I2C_OFFSET=0x300

configs/M5282EVB_defconfig

@@ -17,10 +17,13 @@ CONFIG_CMD_IMLS=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_BOOTP_BOOTFILESIZE=y
 CONFIG_CMD_MII=y
+CONFIG_MII_INIT=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_CACHE=y
 CONFIG_ENV_ADDR=0xFFE04000
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
+CONFIG_SYS_RX_ETH_BUFFER=8
 CONFIG_MTD_NOR_FLASH=y
 CONFIG_FLASH_CFI_DRIVER=y
 CONFIG_SYS_FLASH_PROTECTION=y

configs/M53017EVB_defconfig

@@ -16,11 +16,14 @@ CONFIG_SYS_PROMPT="-> "
 CONFIG_CMD_IMLS=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_MII=y
+CONFIG_MII_INIT=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_CACHE=y
 CONFIG_CMD_DATE=y
 CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_ADDR=0x40000
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
+CONFIG_SYS_RX_ETH_BUFFER=8
 CONFIG_UDP_CHECKSUM=y
 CONFIG_SYS_I2C_LEGACY=y
 CONFIG_SYS_I2C_FSL=y

configs/M5329AFEE_defconfig

@@ -17,11 +17,14 @@ CONFIG_CMD_I2C=y
 CONFIG_CMD_NAND=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_MII=y
+CONFIG_MII_INIT=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_CACHE=y
 CONFIG_CMD_DATE=y
 CONFIG_ENV_ADDR=0x4000
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
+CONFIG_SYS_RX_ETH_BUFFER=8
 CONFIG_UDP_CHECKSUM=y
 CONFIG_SYS_I2C_LEGACY=y
 CONFIG_SYS_I2C_FSL=y

configs/M5329BFEE_defconfig

@@ -17,11 +17,14 @@ CONFIG_CMD_I2C=y
 CONFIG_CMD_NAND=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_MII=y
+CONFIG_MII_INIT=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_CACHE=y
 CONFIG_CMD_DATE=y
 CONFIG_ENV_ADDR=0x4000
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
+CONFIG_SYS_RX_ETH_BUFFER=8
 CONFIG_UDP_CHECKSUM=y
 CONFIG_SYS_I2C_LEGACY=y
 CONFIG_SYS_I2C_FSL=y

configs/M5373EVB_defconfig

@@ -17,11 +17,14 @@ CONFIG_CMD_I2C=y
 CONFIG_CMD_NAND=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_MII=y
+CONFIG_MII_INIT=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_CACHE=y
 CONFIG_CMD_DATE=y
 CONFIG_ENV_ADDR=0x4000
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
+CONFIG_SYS_RX_ETH_BUFFER=8
 CONFIG_UDP_CHECKSUM=y
 CONFIG_SYS_I2C_LEGACY=y
 CONFIG_SYS_I2C_FSL=y

configs/MCR3000_defconfig

@@ -42,6 +42,7 @@ CONFIG_CMD_NAND=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
+CONFIG_MII_INIT=y
 CONFIG_CMD_PING=y
 # CONFIG_CMD_SLEEP is not set
 CONFIG_OF_CONTROL=y

configs/SBx81LIFKW_defconfig

@@ -18,6 +18,7 @@ CONFIG_BOOTDELAY=3
 CONFIG_SILENT_CONSOLE=y
 CONFIG_SILENT_U_BOOT_ONLY=y
 CONFIG_MISC_INIT_R=y
+CONFIG_RESET_PHY_R=y
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_DM=y
 # CONFIG_CMD_FLASH is not set

configs/SBx81LIFXCAT_defconfig

@@ -18,6 +18,7 @@ CONFIG_BOOTDELAY=3
 CONFIG_SILENT_CONSOLE=y
 CONFIG_SILENT_U_BOOT_ONLY=y
 CONFIG_MISC_INIT_R=y
+CONFIG_RESET_PHY_R=y
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_DM=y
 # CONFIG_CMD_FLASH is not set

configs/am43xx_evm_defconfig

@@ -48,6 +48,7 @@ CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
 CONFIG_VERSION_VARIABLE=y
 CONFIG_NET_RETRY_COUNT=10
 CONFIG_BOOTP_SEND_HOSTNAME=y
+CONFIG_SYS_RX_ETH_BUFFER=64
 CONFIG_DM=y
 CONFIG_REGMAP=y
 CONFIG_SPL_REGMAP=y

configs/am43xx_evm_qspiboot_defconfig

@@ -40,6 +40,7 @@ CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
 CONFIG_VERSION_VARIABLE=y
 CONFIG_NET_RETRY_COUNT=10
 CONFIG_BOOTP_SEND_HOSTNAME=y
+CONFIG_SYS_RX_ETH_BUFFER=64
 CONFIG_DM=y
 CONFIG_DFU_MMC=y
 CONFIG_DFU_RAM=y

configs/am43xx_evm_rtconly_defconfig

@@ -42,6 +42,7 @@ CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
 CONFIG_VERSION_VARIABLE=y
 CONFIG_NET_RETRY_COUNT=10
 CONFIG_BOOTP_SEND_HOSTNAME=y
+CONFIG_SYS_RX_ETH_BUFFER=64
 CONFIG_DM=y
 CONFIG_DFU_MMC=y
 CONFIG_DFU_RAM=y

configs/am43xx_evm_usbhost_boot_defconfig

@@ -54,6 +54,7 @@ CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
 CONFIG_VERSION_VARIABLE=y
 CONFIG_NET_RETRY_COUNT=10
 CONFIG_BOOTP_SEND_HOSTNAME=y
+CONFIG_SYS_RX_ETH_BUFFER=64
 CONFIG_DM=y
 CONFIG_REGMAP=y
 CONFIG_SPL_REGMAP=y

configs/am43xx_hs_evm_defconfig

@@ -52,6 +52,7 @@ CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
 CONFIG_VERSION_VARIABLE=y
 CONFIG_NET_RETRY_COUNT=10
 CONFIG_BOOTP_SEND_HOSTNAME=y
+CONFIG_SYS_RX_ETH_BUFFER=64
 CONFIG_DM=y
 CONFIG_REGMAP=y
 CONFIG_SPL_REGMAP=y

configs/at91sam9261ek_dataflash_cs0_defconfig

@@ -26,6 +26,7 @@ CONFIG_USE_BOOTCOMMAND=y
 CONFIG_BOOTCOMMAND="sf probe 0; sf read 0x22000000 0x84000 0x294000; bootm 0x22000000"
 CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 # CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_RESET_PHY_R=y
 CONFIG_SYS_PROMPT="U-Boot> "
 # CONFIG_CMD_BDI is not set
 # CONFIG_CMD_IMI is not set
@@ -63,3 +64,4 @@ CONFIG_DM_SPI=y
 CONFIG_TIMER=y
 CONFIG_ATMEL_PIT_TIMER=y
 CONFIG_USB=y
+CONFIG_ATMEL_LCD_BGR555=y

configs/at91sam9261ek_dataflash_cs3_defconfig

@@ -26,6 +26,7 @@ CONFIG_USE_BOOTCOMMAND=y
 CONFIG_BOOTCOMMAND="sf probe 0:3; sf read 0x22000000 0x84000 0x294000; bootm 0x22000000"
 CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 # CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_RESET_PHY_R=y
 CONFIG_SYS_PROMPT="U-Boot> "
 # CONFIG_CMD_BDI is not set
 # CONFIG_CMD_IMI is not set
@@ -63,3 +64,4 @@ CONFIG_DM_SPI=y
 CONFIG_TIMER=y
 CONFIG_ATMEL_PIT_TIMER=y
 CONFIG_USB=y
+CONFIG_ATMEL_LCD_BGR555=y

configs/at91sam9261ek_nandflash_defconfig

@@ -24,6 +24,7 @@ CONFIG_USE_BOOTCOMMAND=y
 CONFIG_BOOTCOMMAND="nand read 0x22000000 0x200000 0x300000; bootm"
 CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 # CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_RESET_PHY_R=y
 CONFIG_SYS_PROMPT="U-Boot> "
 # CONFIG_CMD_BDI is not set
 # CONFIG_CMD_IMI is not set
@@ -61,3 +62,4 @@ CONFIG_DM_SPI=y
 CONFIG_TIMER=y
 CONFIG_ATMEL_PIT_TIMER=y
 CONFIG_USB=y
+CONFIG_ATMEL_LCD_BGR555=y

configs/at91sam9263ek_dataflash_cs0_defconfig

@@ -26,6 +26,7 @@ CONFIG_USE_BOOTCOMMAND=y
 CONFIG_BOOTCOMMAND="sf probe 0; sf read 0x22000000 0x84000 0x294000; bootm 0x22000000"
 CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 # CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_RESET_PHY_R=y
 CONFIG_HUSH_PARSER=y
 CONFIG_SYS_PROMPT="U-Boot> "
 # CONFIG_CMD_BDI is not set
@@ -67,3 +68,4 @@ CONFIG_DM_SPI=y
 CONFIG_TIMER=y
 CONFIG_ATMEL_PIT_TIMER=y
 CONFIG_USB=y
+CONFIG_ATMEL_LCD_BGR555=y

configs/at91sam9263ek_dataflash_defconfig

@@ -26,6 +26,7 @@ CONFIG_USE_BOOTCOMMAND=y
 CONFIG_BOOTCOMMAND="sf probe 0; sf read 0x22000000 0x84000 0x294000; bootm 0x22000000"
 CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 # CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_RESET_PHY_R=y
 CONFIG_HUSH_PARSER=y
 CONFIG_SYS_PROMPT="U-Boot> "
 # CONFIG_CMD_BDI is not set
@@ -67,3 +68,4 @@ CONFIG_DM_SPI=y
 CONFIG_TIMER=y
 CONFIG_ATMEL_PIT_TIMER=y
 CONFIG_USB=y
+CONFIG_ATMEL_LCD_BGR555=y

configs/at91sam9263ek_nandflash_defconfig

@@ -24,6 +24,7 @@ CONFIG_USE_BOOTCOMMAND=y
 CONFIG_BOOTCOMMAND="nand read 0x22000000 0x200000 0x300000; bootm"
 CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 # CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_RESET_PHY_R=y
 CONFIG_HUSH_PARSER=y
 CONFIG_SYS_PROMPT="U-Boot> "
 # CONFIG_CMD_BDI is not set
@@ -65,3 +66,4 @@ CONFIG_DM_SPI=y
 CONFIG_TIMER=y
 CONFIG_ATMEL_PIT_TIMER=y
 CONFIG_USB=y
+CONFIG_ATMEL_LCD_BGR555=y

configs/at91sam9263ek_norflash_boot_defconfig

@@ -20,6 +20,7 @@ CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_BOOT_NORFLASH"
 CONFIG_BOOTDELAY=3
 CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 # CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_RESET_PHY_R=y
 CONFIG_HUSH_PARSER=y
 CONFIG_SYS_PROMPT="U-Boot> "
 # CONFIG_CMD_BDI is not set
@@ -65,3 +66,4 @@ CONFIG_DM_SPI=y
 CONFIG_TIMER=y
 CONFIG_ATMEL_PIT_TIMER=y
 CONFIG_USB=y
+CONFIG_ATMEL_LCD_BGR555=y

configs/at91sam9263ek_norflash_defconfig

@@ -21,6 +21,7 @@ CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_NORFLASH"
 CONFIG_BOOTDELAY=3
 CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 # CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_RESET_PHY_R=y
 CONFIG_HUSH_PARSER=y
 CONFIG_SYS_PROMPT="U-Boot> "
 # CONFIG_CMD_BDI is not set
@@ -66,3 +67,4 @@ CONFIG_DM_SPI=y
 CONFIG_TIMER=y
 CONFIG_ATMEL_PIT_TIMER=y
 CONFIG_USB=y
+CONFIG_ATMEL_LCD_BGR555=y

configs/at91sam9g10ek_dataflash_cs0_defconfig

@@ -26,6 +26,7 @@ CONFIG_USE_BOOTCOMMAND=y
 CONFIG_BOOTCOMMAND="sf probe 0; sf read 0x22000000 0x84000 0x294000; bootm 0x22000000"
 CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 # CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_RESET_PHY_R=y
 CONFIG_SYS_PROMPT="U-Boot> "
 # CONFIG_CMD_BDI is not set
 # CONFIG_CMD_IMI is not set

configs/at91sam9g10ek_dataflash_cs3_defconfig

@@ -26,6 +26,7 @@ CONFIG_USE_BOOTCOMMAND=y
 CONFIG_BOOTCOMMAND="sf probe 0:3; sf read 0x22000000 0x84000 0x294000; bootm 0x22000000"
 CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 # CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_RESET_PHY_R=y
 CONFIG_SYS_PROMPT="U-Boot> "
 # CONFIG_CMD_BDI is not set
 # CONFIG_CMD_IMI is not set

configs/at91sam9g10ek_nandflash_defconfig

@@ -24,6 +24,7 @@ CONFIG_USE_BOOTCOMMAND=y
 CONFIG_BOOTCOMMAND="nand read 0x22000000 0x200000 0x300000; bootm"
 CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 # CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_RESET_PHY_R=y
 CONFIG_SYS_PROMPT="U-Boot> "
 # CONFIG_CMD_BDI is not set
 # CONFIG_CMD_IMI is not set

configs/at91sam9m10g45ek_mmc_defconfig

@@ -23,6 +23,7 @@ CONFIG_USE_BOOTCOMMAND=y
 CONFIG_BOOTCOMMAND="fatload mmc 0:1 0x71000000 dtb; fatload mmc 0:1 0x72000000 zImage; bootz 0x72000000 - 0x71000000"
 CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 # CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_RESET_PHY_R=y
 CONFIG_HUSH_PARSER=y
 CONFIG_SYS_PROMPT="U-Boot> "
 # CONFIG_CMD_BDI is not set

configs/at91sam9m10g45ek_nandflash_defconfig

@@ -23,6 +23,7 @@ CONFIG_USE_BOOTCOMMAND=y
 CONFIG_BOOTCOMMAND="nand read 0x70000000 0x200000 0x300000;bootm 0x70000000"
 CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 # CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_RESET_PHY_R=y
 CONFIG_HUSH_PARSER=y
 CONFIG_SYS_PROMPT="U-Boot> "
 # CONFIG_CMD_BDI is not set

configs/avnet_ultrazedev_cc_v1_0_ultrazedev_som_v1_0_defconfig

@@ -39,6 +39,7 @@ CONFIG_CMD_EXT4_WRITE=y
 CONFIG_SPL_OF_CONTROL=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
 CONFIG_SPL_DM_SEQ_ALIAS=y
 CONFIG_CLK_ZYNQMP=y
 CONFIG_FPGA_XILINX=y

configs/axm_defconfig

@@ -83,6 +83,7 @@ CONFIG_SYS_NAND_U_BOOT_OFFS=0x20000
 CONFIG_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH_STMICRO=y
 CONFIG_MACB=y
+CONFIG_RMII=y
 CONFIG_PINCTRL=y
 CONFIG_PINCTRL_AT91=y
 CONFIG_SPECIFY_CONSOLE_INDEX=y

configs/bcm968380gerg_ram_defconfig

@@ -49,6 +49,7 @@ CONFIG_MTD_RAW_NAND=y
 CONFIG_NAND_BRCMNAND=y
 CONFIG_NAND_BRCMNAND_6838=y
 CONFIG_SYS_NAND_ONFI_DETECTION=y
+CONFIG_PHY_RESET_DELAY=20
 CONFIG_PHY=y
 CONFIG_BCM6368_USBH_PHY=y
 CONFIG_PINCTRL=y

configs/bitmain_antminer_s9_defconfig

@@ -59,6 +59,7 @@ CONFIG_ENV_IS_IN_FAT=y
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
 CONFIG_BOOTP_SERVERIP=y
 CONFIG_SPL_DM_SEQ_ALIAS=y
 CONFIG_BOOTCOUNT_LIMIT=y

configs/cm_t43_defconfig

@@ -63,6 +63,7 @@ CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
 CONFIG_VERSION_VARIABLE=y
 CONFIG_BOOTP_SEND_HOSTNAME=y
+CONFIG_SYS_RX_ETH_BUFFER=64
 CONFIG_DM=y
 CONFIG_SYS_I2C_LEGACY=y
 CONFIG_SPL_SYS_I2C_LEGACY=y

configs/cobra5272_defconfig

@@ -19,6 +19,8 @@ CONFIG_BOOTP_BOOTFILESIZE=y
 CONFIG_CMD_PING=y
 CONFIG_ENV_ADDR=0xFFE04000
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
+CONFIG_SYS_RX_ETH_BUFFER=8
 CONFIG_SYS_BR0_PRELIM_BOOL=y
 CONFIG_SYS_BR0_PRELIM=0xFFE00201
 CONFIG_SYS_OR0_PRELIM=0xFFE00014

configs/comtrend_ar5315u_ram_defconfig

@@ -40,6 +40,7 @@ CONFIG_CMD_PING=y
 # CONFIG_CMD_SLEEP is not set
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SYS_RX_ETH_BUFFER=6
 # CONFIG_DM_DEVICE_REMOVE is not set
 CONFIG_BCM6348_IUDMA=y
 CONFIG_LED=y
@@ -49,6 +50,7 @@ CONFIG_MTD=y
 CONFIG_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH_WINBOND=y
 CONFIG_SPI_FLASH_MTD=y
+CONFIG_PHY_RESET_DELAY=20
 CONFIG_DM_ETH=y
 CONFIG_BCM6368_ETH=y
 CONFIG_PHY=y

configs/comtrend_ar5387un_ram_defconfig

@@ -40,6 +40,7 @@ CONFIG_CMD_PING=y
 # CONFIG_CMD_SLEEP is not set
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SYS_RX_ETH_BUFFER=6
 # CONFIG_DM_DEVICE_REMOVE is not set
 CONFIG_BCM6348_IUDMA=y
 CONFIG_LED=y
@@ -49,6 +50,7 @@ CONFIG_MTD=y
 CONFIG_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH_MACRONIX=y
 CONFIG_SPI_FLASH_MTD=y
+CONFIG_PHY_RESET_DELAY=20
 CONFIG_DM_ETH=y
 CONFIG_BCM6368_ETH=y
 CONFIG_PHY=y

configs/comtrend_ct5361_ram_defconfig

@@ -38,6 +38,7 @@ CONFIG_CMD_PING=y
 # CONFIG_CMD_SLEEP is not set
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SYS_RX_ETH_BUFFER=6
 # CONFIG_DM_DEVICE_REMOVE is not set
 CONFIG_BCM6348_IUDMA=y
 CONFIG_BCM6345_GPIO=y
@@ -50,6 +51,7 @@ CONFIG_SYS_FLASH_PROTECTION=y
 CONFIG_SYS_FLASH_CFI=y
 CONFIG_SYS_MAX_FLASH_BANKS_DETECT=y
 CONFIG_PHY_FIXED=y
+CONFIG_PHY_RESET_DELAY=20
 CONFIG_DM_ETH=y
 CONFIG_BCM6348_ETH=y
 CONFIG_PHY=y

configs/comtrend_vr3032u_ram_defconfig

@@ -40,6 +40,7 @@ CONFIG_CMD_PING=y
 # CONFIG_CMD_SLEEP is not set
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SYS_RX_ETH_BUFFER=6
 # CONFIG_DM_DEVICE_REMOVE is not set
 CONFIG_BCM6348_IUDMA=y
 CONFIG_LED=y
@@ -51,6 +52,7 @@ CONFIG_MTD_RAW_NAND=y
 CONFIG_NAND_BRCMNAND=y
 CONFIG_NAND_BRCMNAND_6368=y
 CONFIG_SYS_NAND_ONFI_DETECTION=y
+CONFIG_PHY_RESET_DELAY=20
 CONFIG_DM_ETH=y
 CONFIG_BCM6368_ETH=y
 CONFIG_PHY=y

configs/comtrend_wap5813n_ram_defconfig

@@ -38,6 +38,7 @@ CONFIG_CMD_PING=y
 # CONFIG_CMD_SLEEP is not set
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SYS_RX_ETH_BUFFER=6
 # CONFIG_DM_DEVICE_REMOVE is not set
 CONFIG_BCM6348_IUDMA=y
 CONFIG_BCM6345_GPIO=y
@@ -49,6 +50,7 @@ CONFIG_CFI_FLASH=y
 CONFIG_SYS_FLASH_PROTECTION=y
 CONFIG_SYS_FLASH_CFI=y
 CONFIG_SYS_MAX_FLASH_BANKS_DETECT=y
+CONFIG_PHY_RESET_DELAY=20
 CONFIG_DM_ETH=y
 CONFIG_PHY_GIGE=y
 CONFIG_BCM6368_ETH=y

configs/corvus_defconfig

@@ -75,6 +75,7 @@ CONFIG_SYS_NAND_OOBSIZE=0x40
 CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y
 CONFIG_SYS_NAND_U_BOOT_OFFS=0x20000
 CONFIG_MACB=y
+CONFIG_RMII=y
 CONFIG_ATMEL_USART=y
 CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y

configs/d2net_v2_defconfig

@@ -23,6 +23,7 @@ CONFIG_USE_PREBOOT=y
 CONFIG_CONSOLE_MUX=y
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_MISC_INIT_R=y
+CONFIG_RESET_PHY_R=y
 CONFIG_HUSH_PARSER=y
 CONFIG_SYS_PROMPT="d2v2> "
 CONFIG_CMD_EEPROM=y
@@ -45,6 +46,7 @@ CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_ENV_SPI_MAX_HZ=20000000
 CONFIG_ENV_ADDR=0x70000
 CONFIG_NETCONSOLE=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
 CONFIG_DM=y
 CONFIG_SATA_MV=y
 CONFIG_SYS_SATA_MAX_DEVICE=2

configs/devkit3250_defconfig

@@ -44,6 +44,7 @@ CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_USE_BOOTFILE=y
 CONFIG_BOOTFILE="uImage"
 CONFIG_VERSION_VARIABLE=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
 CONFIG_DMA_LPC32XX=y
 CONFIG_LPC32XX_GPIO=y
 CONFIG_SYS_I2C_LEGACY=y
@@ -69,6 +70,7 @@ CONFIG_PHYLIB=y
 CONFIG_PHY_ADDR_ENABLE=y
 CONFIG_PHY_ADDR=31
 CONFIG_PHY_SMSC=y
+CONFIG_RMII=y
 CONFIG_SPECIFY_CONSOLE_INDEX=y
 CONFIG_CONS_INDEX=5
 CONFIG_SYS_NS16550=y

configs/dns325_defconfig

@@ -19,6 +19,7 @@ CONFIG_BOOTCOMMAND="if test -n ${bootenv} && usb start; then if run loadbootenv;
 CONFIG_USE_PREBOOT=y
 CONFIG_CONSOLE_MUX=y
 # CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_RESET_PHY_R=y
 CONFIG_HUSH_PARSER=y
 # CONFIG_CMD_FLASH is not set
 CONFIG_CMD_IDE=y
@@ -40,6 +41,7 @@ CONFIG_OF_CONTROL=y
 CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_NETCONSOLE=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
 CONFIG_DM=y
 CONFIG_SYS_ATA_STRIDE=4
 CONFIG_SYS_ATA_DATA_OFFSET=0x100

configs/dockstar_defconfig

@@ -40,6 +40,7 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_NET_RANDOM_ETHADDR=y
 CONFIG_NETCONSOLE=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
 CONFIG_DM=y
 # CONFIG_MMC is not set
 CONFIG_MTD=y

configs/dreamplug_defconfig

@@ -39,6 +39,7 @@ CONFIG_ENV_SPI_MAX_HZ=50000000
 CONFIG_ENV_ADDR=0x100000
 CONFIG_NET_RANDOM_ETHADDR=y
 CONFIG_NETCONSOLE=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
 CONFIG_DM=y
 CONFIG_SATA_MV=y
 CONFIG_SYS_SATA_MAX_DEVICE=1

configs/ds109_defconfig

@@ -21,6 +21,7 @@ CONFIG_SYS_LOAD_ADDR=0x800000
 CONFIG_USE_BOOTCOMMAND=y
 CONFIG_BOOTCOMMAND="setenv ethact egiga0; ${x_bootcmd_ethernet}; ${x_bootcmd_usb}; ${x_bootcmd_kernel}; setenv bootargs ${x_bootargs} ${x_bootargs_root}; bootm 0x6400000;"
 CONFIG_USE_PREBOOT=y
+CONFIG_RESET_PHY_R=y
 CONFIG_HUSH_PARSER=y
 # CONFIG_CMD_FLASH is not set
 CONFIG_CMD_IDE=y
@@ -38,6 +39,7 @@ CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_ENV_SPI_MAX_HZ=50000000
 CONFIG_ENV_ADDR=0x3D0000
 CONFIG_NETCONSOLE=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
 CONFIG_DM=y
 CONFIG_SYS_ATA_STRIDE=4
 CONFIG_SYS_ATA_DATA_OFFSET=0x100

configs/eb_cpu5282_defconfig

@@ -23,8 +23,11 @@ CONFIG_CMD_I2C=y
 CONFIG_CMD_DHCP=y
 CONFIG_BOOTP_BOOTFILESIZE=y
 CONFIG_CMD_MII=y
+CONFIG_MII_INIT=y
 CONFIG_CMD_DATE=y
 CONFIG_ENV_ADDR=0xFF040000
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
+CONFIG_SYS_RX_ETH_BUFFER=8
 CONFIG_SYS_I2C_LEGACY=y
 CONFIG_SYS_I2C_FSL=y
 CONFIG_SYS_FSL_I2C_OFFSET=0x300

configs/eb_cpu5282_internal_defconfig

@@ -22,8 +22,11 @@ CONFIG_CMD_I2C=y
 CONFIG_CMD_DHCP=y
 CONFIG_BOOTP_BOOTFILESIZE=y
 CONFIG_CMD_MII=y
+CONFIG_MII_INIT=y
 CONFIG_CMD_DATE=y
 CONFIG_ENV_ADDR=0xFF040000
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
+CONFIG_SYS_RX_ETH_BUFFER=8
 CONFIG_SYS_I2C_LEGACY=y
 CONFIG_SYS_I2C_FSL=y
 CONFIG_SYS_FSL_I2C_OFFSET=0x300

configs/edminiv2_defconfig

@@ -18,6 +18,7 @@ CONFIG_SYS_LOAD_ADDR=0x800000
 CONFIG_BOOTDELAY=3
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_ARCH_MISC_INIT=y
+CONFIG_RESET_PHY_R=y
 CONFIG_SPL_BOARD_INIT=y
 CONFIG_SPL_NOR_SUPPORT=y
 CONFIG_HUSH_PARSER=y
@@ -33,6 +34,7 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_ADDR=0xFFF84000
 CONFIG_NETCONSOLE=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
 CONFIG_SYS_IDE_MAXBUS=1
 CONFIG_SYS_IDE_MAXDEVICE=1
 CONFIG_SYS_ATA_BASE_ADDR=0xf1080000

configs/ethernut5_defconfig

@@ -75,6 +75,7 @@ CONFIG_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH_ATMEL=y
 CONFIG_SPI_FLASH_DATAFLASH=y
 CONFIG_MACB=y
+CONFIG_RMII=y
 CONFIG_PINCTRL=y
 CONFIG_PINCTRL_AT91=y
 CONFIG_RTC_PCF8563=y

configs/goflexhome_defconfig

@@ -43,6 +43,7 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_NET_RANDOM_ETHADDR=y
 CONFIG_NETCONSOLE=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
 CONFIG_DM=y
 CONFIG_SATA_MV=y
 CONFIG_SYS_SATA_MAX_DEVICE=1

configs/gurnard_defconfig

@@ -15,6 +15,7 @@ CONFIG_FIT=y
 CONFIG_BOOTDELAY=3
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_RESET_PHY_R=y
 CONFIG_HUSH_PARSER=y
 # CONFIG_CMD_BDI is not set
 # CONFIG_CMD_IMI is not set
@@ -39,6 +40,7 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_NET_RETRY_COUNT=20
+CONFIG_TFTP_PORT=y
 CONFIG_TFTP_TSIZE=y
 CONFIG_AT91_GPIO=y
 CONFIG_GENERIC_ATMEL_MCI=y
@@ -48,6 +50,7 @@ CONFIG_MTD_RAW_NAND=y
 CONFIG_NAND_ATMEL=y
 CONFIG_ATMEL_NAND_HWECC=y
 CONFIG_MACB=y
+CONFIG_RMII=y
 CONFIG_ATMEL_USART=y
 CONFIG_TIMER=y
 CONFIG_ATMEL_PIT_TIMER=y
@@ -56,4 +59,6 @@ CONFIG_USB_EHCI_HCD=y
 CONFIG_DM_VIDEO=y
 # CONFIG_VIDEO_LOGO is not set
 # CONFIG_VIDEO_BPP32 is not set
+CONFIG_ATMEL_LCD=y
+CONFIG_LCD=y
 CONFIG_CMD_DHRYSTONE=y

configs/guruplug_defconfig

@@ -18,6 +18,7 @@ CONFIG_USE_BOOTCOMMAND=y
 CONFIG_BOOTCOMMAND="setenv bootargs ${console} ${mtdparts} ${bootargs_root}; ubi part root; ubifsmount ubi:rootfs; ubifsload 0x800000 ${kernel}; ubifsload 0x700000 ${fdt}; ubifsumount; fdt addr 0x700000; fdt resize; fdt chosen; bootz 0x800000 - 0x700000"
 CONFIG_USE_PREBOOT=y
 # CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_RESET_PHY_R=y
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_BOOTZ=y
 # CONFIG_CMD_FLASH is not set
@@ -42,6 +43,7 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_NETCONSOLE=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
 CONFIG_DM=y
 CONFIG_SYS_ATA_STRIDE=4
 CONFIG_SYS_ATA_DATA_OFFSET=0x100

configs/huawei_hg556a_ram_defconfig

@@ -38,6 +38,7 @@ CONFIG_CMD_PING=y
 # CONFIG_CMD_SLEEP is not set
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SYS_RX_ETH_BUFFER=6
 # CONFIG_DM_DEVICE_REMOVE is not set
 CONFIG_BCM6348_IUDMA=y
 CONFIG_BCM6345_GPIO=y
@@ -50,6 +51,7 @@ CONFIG_SYS_FLASH_PROTECTION=y
 CONFIG_SYS_FLASH_CFI=y
 CONFIG_SYS_MAX_FLASH_BANKS_DETECT=y
 CONFIG_PHY_FIXED=y
+CONFIG_PHY_RESET_DELAY=20
 CONFIG_DM_ETH=y
 CONFIG_BCM6348_ETH=y
 CONFIG_PHY=y

configs/ib62x0_defconfig

@@ -41,6 +41,7 @@ CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_NETCONSOLE=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
 CONFIG_DM=y
 CONFIG_SYS_ATA_STRIDE=4
 CONFIG_SYS_ATA_DATA_OFFSET=0x100

configs/iconnect_defconfig

@@ -42,6 +42,7 @@ CONFIG_ENV_IS_IN_NAND=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_NET_RANDOM_ETHADDR=y
 CONFIG_NETCONSOLE=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
 CONFIG_DM=y
 # CONFIG_MMC is not set
 CONFIG_MTD=y

configs/inetspace_v2_defconfig

@@ -23,6 +23,7 @@ CONFIG_USE_PREBOOT=y
 CONFIG_CONSOLE_MUX=y
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_MISC_INIT_R=y
+CONFIG_RESET_PHY_R=y
 CONFIG_HUSH_PARSER=y
 CONFIG_SYS_PROMPT="ns2> "
 CONFIG_CMD_EEPROM=y
@@ -45,6 +46,7 @@ CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_ENV_SPI_MAX_HZ=20000000
 CONFIG_ENV_ADDR=0x70000
 CONFIG_NETCONSOLE=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
 CONFIG_DM=y
 CONFIG_SATA_MV=y
 CONFIG_SYS_SATA_MAX_DEVICE=1

configs/integratorap_cm720t_defconfig

@@ -22,6 +22,7 @@ CONFIG_CMD_ARMFLASH=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_BOOTP_BOOTFILESIZE=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_SYS_RX_ETH_BUFFER=8
 # CONFIG_MMC is not set
 CONFIG_MTD_NOR_FLASH=y
 CONFIG_FLASH_CFI_DRIVER=y

configs/integratorap_cm920t_defconfig

@@ -22,6 +22,7 @@ CONFIG_CMD_ARMFLASH=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_BOOTP_BOOTFILESIZE=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_SYS_RX_ETH_BUFFER=8
 # CONFIG_MMC is not set
 CONFIG_MTD_NOR_FLASH=y
 CONFIG_FLASH_CFI_DRIVER=y

configs/integratorap_cm926ejs_defconfig

@@ -22,6 +22,7 @@ CONFIG_CMD_ARMFLASH=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_BOOTP_BOOTFILESIZE=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_SYS_RX_ETH_BUFFER=8
 # CONFIG_MMC is not set
 CONFIG_MTD_NOR_FLASH=y
 CONFIG_FLASH_CFI_DRIVER=y

configs/integratorap_cm946es_defconfig

@@ -22,6 +22,7 @@ CONFIG_CMD_ARMFLASH=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_BOOTP_BOOTFILESIZE=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_SYS_RX_ETH_BUFFER=8
 # CONFIG_MMC is not set
 CONFIG_MTD_NOR_FLASH=y
 CONFIG_FLASH_CFI_DRIVER=y

configs/km_kirkwood_128m16_defconfig

@@ -19,6 +19,7 @@ CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n"
 CONFIG_AUTOBOOT_STOP_STR=" "
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_MISC_INIT_R=y
+CONFIG_RESET_PHY_R=y
 CONFIG_HUSH_PARSER=y
 # CONFIG_BOOTM_NETBSD is not set
 # CONFIG_BOOTM_PLAN9 is not set
@@ -48,6 +49,7 @@ CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_VERSION_VARIABLE=y
 CONFIG_NETCONSOLE=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
 CONFIG_BOOTCOUNT_LIMIT=y
 CONFIG_BOOTCOUNT_RAM=y
 CONFIG_KIRKWOOD_GPIO=y

configs/km_kirkwood_defconfig

@@ -19,6 +19,7 @@ CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n"
 CONFIG_AUTOBOOT_STOP_STR=" "
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_MISC_INIT_R=y
+CONFIG_RESET_PHY_R=y
 CONFIG_HUSH_PARSER=y
 # CONFIG_BOOTM_NETBSD is not set
 # CONFIG_BOOTM_PLAN9 is not set
@@ -48,6 +49,7 @@ CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_VERSION_VARIABLE=y
 CONFIG_NETCONSOLE=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
 CONFIG_BOOTCOUNT_LIMIT=y
 CONFIG_BOOTCOUNT_RAM=y
 CONFIG_KIRKWOOD_GPIO=y

configs/km_kirkwood_pci_defconfig

@@ -20,6 +20,7 @@ CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n"
 CONFIG_AUTOBOOT_STOP_STR=" "
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_MISC_INIT_R=y
+CONFIG_RESET_PHY_R=y
 CONFIG_HUSH_PARSER=y
 # CONFIG_BOOTM_NETBSD is not set
 # CONFIG_BOOTM_PLAN9 is not set
@@ -49,6 +50,7 @@ CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_VERSION_VARIABLE=y
 CONFIG_NETCONSOLE=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
 CONFIG_BOOTCOUNT_LIMIT=y
 CONFIG_BOOTCOUNT_RAM=y
 CONFIG_KIRKWOOD_GPIO=y

configs/kmcoge5un_defconfig

@@ -23,6 +23,7 @@ CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n"
 CONFIG_AUTOBOOT_STOP_STR=" "
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_MISC_INIT_R=y
+CONFIG_RESET_PHY_R=y
 CONFIG_HUSH_PARSER=y
 # CONFIG_BOOTM_NETBSD is not set
 # CONFIG_BOOTM_PLAN9 is not set
@@ -52,6 +53,7 @@ CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_VERSION_VARIABLE=y
 CONFIG_NETCONSOLE=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
 CONFIG_BOOTCOUNT_LIMIT=y
 CONFIG_BOOTCOUNT_RAM=y
 CONFIG_KIRKWOOD_GPIO=y

configs/kmnusa_defconfig

@@ -23,6 +23,7 @@ CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n"
 CONFIG_AUTOBOOT_STOP_STR=" "
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_MISC_INIT_R=y
+CONFIG_RESET_PHY_R=y
 CONFIG_HUSH_PARSER=y
 # CONFIG_BOOTM_NETBSD is not set
 # CONFIG_BOOTM_PLAN9 is not set
@@ -52,6 +53,7 @@ CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_VERSION_VARIABLE=y
 CONFIG_NETCONSOLE=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
 CONFIG_BOOTCOUNT_LIMIT=y
 CONFIG_BOOTCOUNT_RAM=y
 CONFIG_KIRKWOOD_GPIO=y

configs/kmsuse2_defconfig

@@ -24,6 +24,7 @@ CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n"
 CONFIG_AUTOBOOT_STOP_STR=" "
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_MISC_INIT_R=y
+CONFIG_RESET_PHY_R=y
 CONFIG_HUSH_PARSER=y
 # CONFIG_BOOTM_NETBSD is not set
 # CONFIG_BOOTM_PLAN9 is not set
@@ -53,6 +54,7 @@ CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_VERSION_VARIABLE=y
 CONFIG_NETCONSOLE=y
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
 CONFIG_BOOTCOUNT_LIMIT=y
 CONFIG_BOOTCOUNT_RAM=y
 CONFIG_KIRKWOOD_GPIO=y

configs/kontron_sl28_defconfig

@@ -59,6 +59,7 @@ CONFIG_OF_LIST="fsl-ls1028a-kontron-sl28 fsl-ls1028a-kontron-sl28-var1 fsl-ls102
 CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
+CONFIG_SYS_RX_ETH_BUFFER=8
 CONFIG_SPL_DM_SEQ_ALIAS=y
 CONFIG_SATA=y
 CONFIG_SCSI_AHCI=y

configs/ls1028aqds_tfa_SECURE_BOOT_defconfig

@@ -43,6 +43,7 @@ CONFIG_OF_CONTROL=y
 CONFIG_ENV_OVERWRITE=y
 CONFIG_NET_RANDOM_ETHADDR=y
 CONFIG_NETCONSOLE=y
+CONFIG_SYS_RX_ETH_BUFFER=8
 CONFIG_DM=y
 CONFIG_SATA=y
 CONFIG_SCSI_AHCI=y

configs/ls1028aqds_tfa_defconfig

@@ -48,6 +48,7 @@ CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_ENV_ADDR=0x20500000
 CONFIG_NET_RANDOM_ETHADDR=y
 CONFIG_NETCONSOLE=y
+CONFIG_SYS_RX_ETH_BUFFER=8
 CONFIG_DM=y
 CONFIG_SATA=y
 CONFIG_SCSI_AHCI=y

configs/ls1028aqds_tfa_lpuart_defconfig

@@ -48,6 +48,7 @@ CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_ENV_ADDR=0x20500000
 CONFIG_NET_RANDOM_ETHADDR=y
 CONFIG_NETCONSOLE=y
+CONFIG_SYS_RX_ETH_BUFFER=8
 CONFIG_DM=y
 CONFIG_SATA=y
 CONFIG_SCSI_AHCI=y

configs/ls1028ardb_tfa_SECURE_BOOT_defconfig

@@ -42,6 +42,7 @@ CONFIG_OF_CONTROL=y
 CONFIG_ENV_OVERWRITE=y
 CONFIG_NET_RANDOM_ETHADDR=y
 CONFIG_NETCONSOLE=y
+CONFIG_SYS_RX_ETH_BUFFER=8
 CONFIG_DM=y
 CONFIG_SATA=y
 CONFIG_SCSI_AHCI=y

configs/ls1028ardb_tfa_defconfig

@@ -47,6 +47,7 @@ CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_ENV_ADDR=0x20500000
 CONFIG_NET_RANDOM_ETHADDR=y
 CONFIG_NETCONSOLE=y
+CONFIG_SYS_RX_ETH_BUFFER=8
 CONFIG_DM=y
 CONFIG_SATA=y
 CONFIG_SCSI_AHCI=y

configs/ls1088aqds_defconfig

@@ -31,6 +31,7 @@ CONFIG_USE_BOOTCOMMAND=y
 CONFIG_BOOTCOMMAND="fsl_mc lazyapply dpl 0x580d00000 && cp.b $kernel_start $kernel_load $kernel_size && bootm $kernel_load"
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_RESET_PHY_R=y
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_GREPENV=y
 CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5

configs/ls1088aqds_qspi_SECURE_BOOT_defconfig

@@ -32,6 +32,7 @@ CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21
 CONFIG_BOOTCOMMAND="sf probe 0:0;sf read 0x80001000 0xd00000 0x100000; fsl_mc lazyapply dpl 0x80001000 && sf read $kernel_load $kernel_start $kernel_size && bootm $kernel_load"
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_RESET_PHY_R=y
 CONFIG_CMD_GREPENV=y
 CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
 CONFIG_CMD_MEMINFO=y

configs/ls1088aqds_qspi_defconfig

@@ -33,6 +33,7 @@ CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21
 CONFIG_BOOTCOMMAND="sf probe 0:0;sf read 0x80001000 0xd00000 0x100000; fsl_mc lazyapply dpl 0x80001000 && sf read $kernel_load $kernel_start $kernel_size && bootm $kernel_load"
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_RESET_PHY_R=y
 CONFIG_CMD_GREPENV=y
 CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
 CONFIG_CMD_MEMINFO=y

configs/ls1088aqds_sdcard_ifc_defconfig

@@ -37,6 +37,7 @@ CONFIG_USE_BOOTCOMMAND=y
 CONFIG_BOOTCOMMAND="mmcinfo;mmc read 0x80001000 0x6800 0x800; fsl_mc lazyapply dpl 0x80001000 && mmc read $kernel_load $kernel_start $kernel_size && bootm $kernel_load"
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_RESET_PHY_R=y
 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x8b0
 CONFIG_SPL_ENV_SUPPORT=y

configs/ls1088aqds_sdcard_qspi_defconfig

@@ -38,6 +38,7 @@ CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21
 CONFIG_BOOTCOMMAND="mmcinfo;mmc read 0x80001000 0x6800 0x800; fsl_mc lazyapply dpl 0x80001000 && mmc read $kernel_load $kernel_start $kernel_size && bootm $kernel_load"
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_RESET_PHY_R=y
 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x8b0
 CONFIG_SPL_ENV_SUPPORT=y

configs/ls1088aqds_tfa_defconfig

@@ -35,6 +35,7 @@ CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_DISPLAY_BOARDINFO_LATE=y
 CONFIG_MISC_INIT_R=y
+CONFIG_RESET_PHY_R=y
 CONFIG_CMD_GREPENV=y
 CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
 CONFIG_CMD_MEMINFO=y

configs/ls1088ardb_qspi_SECURE_BOOT_defconfig

@@ -33,6 +33,7 @@ CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_DISPLAY_BOARDINFO_LATE=y
 CONFIG_MISC_INIT_R=y
+CONFIG_RESET_PHY_R=y
 CONFIG_CMD_GREPENV=y
 CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
 CONFIG_CMD_MEMINFO=y

configs/ls1088ardb_qspi_defconfig

@@ -34,6 +34,7 @@ CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_DISPLAY_BOARDINFO_LATE=y
 CONFIG_MISC_INIT_R=y
+CONFIG_RESET_PHY_R=y
 CONFIG_CMD_GREPENV=y
 CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
 CONFIG_CMD_MEMINFO=y

configs/ls1088ardb_sdcard_qspi_SECURE_BOOT_defconfig

@@ -38,6 +38,7 @@ CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_DISPLAY_BOARDINFO_LATE=y
 CONFIG_MISC_INIT_R=y
+CONFIG_RESET_PHY_R=y
 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x8b0
 CONFIG_SPL_ENV_SUPPORT=y

configs/ls1088ardb_sdcard_qspi_defconfig

@@ -39,6 +39,7 @@ CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_DISPLAY_BOARDINFO_LATE=y
 CONFIG_MISC_INIT_R=y
+CONFIG_RESET_PHY_R=y
 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x8b0
 CONFIG_SPL_ENV_SUPPORT=y