rockchip: rk3399-gru: Sync DT from Linux kernel v6.8

Sync rk3399-gru related device tree from Linux kernel v6.8.

The spi_flash symbol is no longer part of upstream DT, it is re-defined
to allow existing reference use in related u-boot.dtsi-files.

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>

arch/arm/dts/rk3399-gru-bob.dts

@@ -16,6 +16,7 @@
 		     "google,bob-rev7", "google,bob-rev6",
 		     "google,bob-rev5", "google,bob-rev4",
 		     "google,bob", "google,gru", "rockchip,rk3399";
+	chassis-type = "convertible";
 
 	edp_panel: edp-panel {
 		compatible = "boe,nv101wxmn51";
@@ -69,7 +70,7 @@
 &spi0 {
 	status = "okay";
 
-	cr50@0 {
+	tpm@0 {
 		compatible = "google,cr50";
 		reg = <0>;
 		interrupt-parent = <&gpio0>;
@@ -87,3 +88,8 @@
 		};
 	};
 };
+
+&wlan_host_wake_l {
+	/* Kevin has an external pull up, but Bob does not. */
+	rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>;
+};

arch/arm/dts/rk3399-gru-chromebook.dtsi

@@ -198,7 +198,6 @@
 		power-supply = <&pp3300_disp>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&bl_en>;
-		pwm-delay-us = <10000>;
 	};
 
 	gpio_keys: gpio-keys {
@@ -206,7 +205,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&bt_host_wake_l>;
 
-		wake_on_bt: wake-on-bt {
+		wake_on_bt: key-wake-on-bt {
 			label = "Wake-on-Bluetooth";
 			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WAKEUP>;
@@ -234,9 +233,24 @@
 	extcon = <&usbc_extcon0>, <&usbc_extcon1>;
 };
 
+&dmc {
+	center-supply = <&ppvar_centerlogic>;
+	rockchip,pd-idle-dis-freq-hz = <800000000>;
+	rockchip,sr-idle-dis-freq-hz = <800000000>;
+	rockchip,sr-mc-gate-idle-dis-freq-hz = <800000000>;
+};
+
 &edp {
 	status = "okay";
 
+	/*
+	 * eDP PHY/clk don't sync reliably at anything other than 24 MHz. Only
+	 * set this here, because rk3399-gru.dtsi ensures we can generate this
+	 * off GPLL=600MHz, whereas some other RK3399 boards may not.
+	 */
+	assigned-clocks = <&cru PCLK_EDP>;
+	assigned-clock-rates = <24000000>;
+
 	ports {
 		edp_out: port@1 {
 			reg = <1>;
@@ -251,6 +265,182 @@
 	};
 };
 
+&gpio0 {
+	gpio-line-names = /* GPIO0 A 0-7 */
+			  "AP_RTC_CLK_IN",
+			  "EC_AP_INT_L",
+			  "PP1800_AUDIO_EN",
+			  "BT_HOST_WAKE_L",
+			  "WLAN_MODULE_PD_L",
+			  "H1_INT_OD_L",
+			  "CENTERLOGIC_DVS_PWM",
+			  "",
+
+			  /* GPIO0 B 0-4 */
+			  "WIFI_HOST_WAKE_L",
+			  "PMUIO2_33_18_L",
+			  "PP1500_EN",
+			  "AP_EC_WARM_RESET_REQ",
+			  "PP3000_EN";
+};
+
+&gpio1 {
+	gpio-line-names = /* GPIO1 A 0-7 */
+			  "",
+			  "",
+			  "SPK_PA_EN",
+			  "",
+			  "TRACKPAD_INT_L",
+			  "AP_EC_S3_S0_L",
+			  "AP_EC_OVERTEMP",
+			  "AP_SPI_FLASH_MISO",
+
+			  /* GPIO1 B 0-7 */
+			  "AP_SPI_FLASH_MOSI_R",
+			  "AP_SPI_FLASH_CLK_R",
+			  "AP_SPI_FLASH_CS_L_R",
+			  "WLAN_MODULE_RESET_L",
+			  "WIFI_DISABLE_L",
+			  "MIC_INT",
+			  "",
+			  "AP_I2C_DVS_SDA",
+
+			  /* GPIO1 C 0-7 */
+			  "AP_I2C_DVS_SCL",
+			  "AP_BL_EN",
+			  /*
+			   * AP_FLASH_WP is crossystem ABI. Schematics call it
+			   * AP_FW_WP or CPU1_FW_WP, depending on the variant.
+			   */
+			  "AP_FLASH_WP",
+			  "LITCPU_DVS_PWM",
+			  "AP_I2C_AUDIO_SDA",
+			  "AP_I2C_AUDIO_SCL",
+			  "",
+			  "HEADSET_INT_L";
+};
+
+&gpio2 {
+	gpio-line-names = /* GPIO2 A 0-7 */
+			  "",
+			  "",
+			  "SD_IO_PWR_EN",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+
+			  /* GPIO2 B 0-7 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+
+			  /* GPIO2 C 0-7 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "AP_SPI_EC_MISO",
+			  "AP_SPI_EC_MOSI",
+			  "AP_SPI_EC_CLK",
+			  "AP_SPI_EC_CS_L",
+
+			  /* GPIO2 D 0-4 */
+			  "BT_DEV_WAKE_L",
+			  "",
+			  "WIFI_PCIE_CLKREQ_L",
+			  "WIFI_PERST_L",
+			  "SD_PWR_3000_1800_L";
+};
+
+&gpio3 {
+	gpio-line-names = /* GPIO3 A 0-7 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "AP_SPI_TPM_MISO",
+			  "AP_SPI_TPM_MOSI_R",
+			  "AP_SPI_TPM_CLK_R",
+			  "AP_SPI_TPM_CS_L_R",
+
+			  /* GPIO3 B 0-7 */
+			  "EC_IN_RW",
+			  "",
+			  "AP_I2C_TP_SDA",
+			  "AP_I2C_TP_SCL",
+			  "AP_I2C_TP_PU_EN",
+			  "TOUCH_INT_L",
+			  "",
+			  "",
+
+			  /* GPIO3 C 0-7 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+
+			  /* GPIO3 D 0-7 */
+			  "I2S0_SCLK",
+			  "I2S0_LRCK_RX",
+			  "I2S0_LRCK_TX",
+			  "I2S0_SDI_0",
+			  "I2S0_SDI_1",
+			  "",
+			  "I2S0_SDO_1",
+			  "I2S0_SDO_0";
+};
+
+&gpio4 {
+	gpio-line-names = /* GPIO4 A 0-7 */
+			  "I2S_MCLK",
+			  "AP_I2C_MIC_SDA",
+			  "AP_I2C_MIC_SCL",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+
+			  /* GPIO4 B 0-7 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+
+			  /* GPIO4 C 0-7 */
+			  "AP_I2C_TS_SDA",
+			  "AP_I2C_TS_SCL",
+			  "GPU_DVS_PWM",
+			  "UART_DBG_TX_AP_RX",
+			  "UART_AP_TX_DBG_RX",
+			  "",
+			  "BIGCPU_DVS_PWM",
+			  "EDP_HPD_3V0",
+
+			  /* GPIO4 D 0-5 */
+			  "SD_CARD_DET_L",
+			  "USB_DP_HPD",
+			  "TOUCH_RESET_L",
+			  "PP3300_DISP_EN",
+			  "",
+			  "SD_SLOT_PWR_EN";
+};
+
 ap_i2c_mic: &i2c1 {
 	status = "okay";
 
@@ -286,7 +476,7 @@ ap_i2c_tp: &i2c5 {
 };
 
 &cros_ec {
-	cros_ec_pwm: ec-pwm {
+	cros_ec_pwm: pwm {
 		compatible = "google,cros-ec-pwm";
 		#pwm-cells = <1>;
 	};
@@ -319,8 +509,7 @@ ap_i2c_tp: &i2c5 {
 &pci_rootport {
 	mvl_wifi: wifi@0,0 {
 		compatible = "pci1b4b,2b42";
-		reg = <0x83010000 0x0 0x00000000 0x0 0x00100000
+		reg = <0x0000 0x0 0x0 0x0 0x0>;
-		       0x83010000 0x0 0x00100000 0x0 0x00100000>;
 		interrupt-parent = <&gpio0>;
 		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
 		pinctrl-names = "default";
@@ -395,6 +584,7 @@ ap_i2c_tp: &i2c5 {
 	};
 
 	wlan_host_wake_l: wlan-host-wake-l {
+		/* Kevin has an external pull up, but Bob does not */
 		rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
 	};
 };

arch/arm/dts/rk3399-gru-kevin.dts

@@ -24,6 +24,7 @@
 		     "google,kevin-rev9", "google,kevin-rev8",
 		     "google,kevin-rev7", "google,kevin-rev6",
 		     "google,kevin", "google,gru", "rockchip,rk3399";
+	chassis-type = "convertible";
 
 	/* Power tree */
 
@@ -91,7 +92,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&bt_host_wake_l>, <&cpu1_pen_eject>;
 
-	pen-insert {
+	switch-pen-insert {
 		label = "Pen Insert";
 		/* Insert = low, eject = high */
 		gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;

arch/arm/dts/rk3399-gru-u-boot.dtsi

@@ -78,12 +78,14 @@
 	/delete-property/ bootph-pre-ram;
 };
 
+&spi1 {
+	spi_flash: flash@0 {
+		bootph-all;
+	};
+};
+
 &spi5 {
 	spi-activate-delay = <100>;
 	spi-max-frequency = <3000000>;
 	spi-deactivate-delay = <200>;
 };
-
-&spi_flash {
-	bootph-all;
-};

arch/arm/dts/rk3399-gru.dtsi

@@ -250,7 +250,7 @@
 		pinctrl-0 = <&sd_io_pwr_en &sd_pwr_1800_sel>;
 
 		enable-active-high;
-		enable-gpio = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+		enable-gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
 		gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>;
 		states = <1800000 0x1>,
 			 <3000000 0x0>;
@@ -286,7 +286,7 @@
 
 	sound: sound {
 		compatible = "rockchip,rk3399-gru-sound";
-		rockchip,cpu = <&i2s0 &i2s2>;
+		rockchip,cpu = <&i2s0 &spdif>;
 	};
 };
 
@@ -373,6 +373,34 @@
 		<200000000>;
 };
 
+&dfi {
+	status = "okay";
+};
+
+&dmc {
+	status = "okay";
+
+	rockchip,pd-idle-ns = <160>;
+	rockchip,sr-idle-ns = <10240>;
+	rockchip,sr-mc-gate-idle-ns = <40960>;
+	rockchip,srpd-lite-idle-ns = <61440>;
+	rockchip,standby-idle-ns = <81920>;
+
+	rockchip,ddr3_odt_dis_freq = <666000000>;
+	rockchip,lpddr3_odt_dis_freq = <666000000>;
+	rockchip,lpddr4_odt_dis_freq = <666000000>;
+
+	rockchip,sr-mc-gate-idle-dis-freq-hz = <1000000000>;
+	rockchip,srpd-lite-idle-dis-freq-hz = <0>;
+	rockchip,standby-idle-dis-freq-hz = <928000000>;
+};
+
+&dmc_opp_table {
+	opp03 {
+		opp-suspend;
+	};
+};
+
 &emmc_phy {
 	status = "okay";
 };
@@ -437,10 +465,6 @@ ap_i2c_audio: &i2c8 {
 	status = "okay";
 };
 
-&i2s2 {
-	status = "okay";
-};
-
 &io_domains {
 	status = "okay";
 
@@ -461,10 +485,11 @@ ap_i2c_audio: &i2c8 {
 	vpcie0v9-supply = <&pp900_pcie>;
 
 	pci_rootport: pcie@0,0 {
-		reg = <0x83000000 0x0 0x00000000 0x0 0x00000000>;
+		reg = <0x0000 0 0 0 0>;
 		#address-cells = <3>;
 		#size-cells = <2>;
 		ranges;
+		device_type = "pci";
 	};
 };
 
@@ -537,13 +562,24 @@ ap_i2c_audio: &i2c8 {
 	vqmmc-supply = <&ppvar_sd_card_io>;
 };
 
+&spdif {
+	status = "okay";
+
+	/*
+	 * SPDIF is routed internally to DP; we either don't use these pins, or
+	 * mux them to something else.
+	 */
+	/delete-property/ pinctrl-0;
+	/delete-property/ pinctrl-names;
+};
+
 &spi1 {
 	status = "okay";
 
 	pinctrl-names = "default", "sleep";
 	pinctrl-1 = <&spi1_sleep>;
 
-	spi_flash: spiflash@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;