Merge https://source.denx.de/u-boot/custodians/u-boot-marvell

- kirkwood: pogo_v4 & nsa310s: Add distro boot (Tony)
- kirkwood: add DM timer support and use it on lsxl boards (Michael)
- kirkwood: convert the Buffalo Linkstation LS-CHLv2 and XHL boards
  to DM (Michael)
- mvebu: turris_mox/omnia: misc improments (Pali)
- mvebu: mbus: Fix mbus driver to work also after U-Boot relocation (Pali)

arch/arm/dts/kirkwood-lschlv2-u-boot.dtsi

@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+&eth0 {
+	status = "disabled";
+};
+
+&hdd_power {
+	/delete-property/ regulator-always-on;
+};
+
+&usb_power {
+	/delete-property/ regulator-always-on;
+};

arch/arm/dts/kirkwood-lsxhl-u-boot.dtsi

@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+&eth0 {
+	status = "disabled";
+};
+
+&hdd_power {
+	/delete-property/ regulator-always-on;
+};
+
+&usb_power {
+	/delete-property/ regulator-always-on;
+};

arch/arm/mach-kirkwood/Kconfig

@@ -45,6 +45,8 @@ config TARGET_LSXL
 	bool "lsxl Board"
 	select FEROCEON_88FR131
 	select KW88F6281
+	select BOARD_EARLY_INIT_R
+	select MISC_INIT_R
 
 config TARGET_POGO_E02
 	bool "pogo_e02 Board"

arch/arm/mach-kirkwood/include/mach/config.h

@@ -51,8 +51,10 @@
 #endif /* CONFIG_IDE */
 
 /* Use common timer */
+#ifndef CONFIG_TIMER
 #define CONFIG_SYS_TIMER_COUNTS_DOWN
 #define CONFIG_SYS_TIMER_COUNTER	(MVEBU_TIMER_BASE + 0x14)
 #define CONFIG_SYS_TIMER_RATE		CONFIG_SYS_TCLK
+#endif
 
 #endif /* _KW_CONFIG_H */

arch/arm/mach-kirkwood/include/mach/cpu.h

@@ -144,9 +144,6 @@ struct kwgpio_registers {
 	u32 irq_level;
 };
 
-/* Needed for dynamic (board-specific) mbus configuration */
-extern struct mvebu_mbus_state mbus_state;
-
 /*
  * functions
  */

arch/arm/mach-kirkwood/include/mach/kw88f6281.h

@@ -15,6 +15,7 @@
 #define KW_REGS_PHY_BASE		KW88F6281_REGS_PHYS_BASE
 
 /* TCLK Core Clock definition */
-#define CONFIG_SYS_TCLK	200000000 /* 200MHz */
+#define CONFIG_SYS_TCLK			((readl(CONFIG_SAR_REG) & BIT(21)) ? \
+					166666667 : 200000000)
 
 #endif /* _ASM_ARCH_KW88F6281_H */

arch/arm/mach-kirkwood/include/mach/soc.h

@@ -62,6 +62,8 @@
 #define MVCPU_WIN_ENABLE	KWCPU_WIN_ENABLE
 #define MVCPU_WIN_DISABLE	KWCPU_WIN_DISABLE
 
+#define CONFIG_SAR_REG		(KW_MPP_BASE + 0x0030)
+
 #if defined (CONFIG_KW88F6281)
 #include <asm/arch/kw88f6281.h>
 #elif defined (CONFIG_KW88F6192)

arch/arm/mach-mvebu/Makefile

@@ -15,7 +15,10 @@ ifdef CONFIG_ARCH_KIRKWOOD
 obj-y	= dram.o
 obj-y	+= gpio.o
 obj-y	+= mbus.o
+
+ifndef CONFIG_TIMER
 obj-y	+= timer.o
+endif
 
 else # CONFIG_ARCH_KIRKWOOD
 

arch/arm/mach-mvebu/include/mach/cpu.h

@@ -122,9 +122,6 @@ struct sar_freq_modes {
 	u32 d_clk;
 };
 
-/* Needed for dynamic (board-specific) mbus configuration */
-extern struct mvebu_mbus_state mbus_state;
-
 /*
  * functions
  */

arch/arm/mach-mvebu/mbus.c

@@ -88,31 +88,34 @@
 
 #define DOVE_DDR_BASE_CS_OFF(n) ((n) << 4)
 
-struct mvebu_mbus_state;
-
-struct mvebu_mbus_soc_data {
-	unsigned int num_wins;
-	unsigned int num_remappable_wins;
-	unsigned int (*win_cfg_offset)(const int win);
-	void (*setup_cpu_target)(struct mvebu_mbus_state *s);
-};
-
-struct mvebu_mbus_state mbus_state
-	__section(".data");
 static struct mbus_dram_target_info mbus_dram_info
 	__section(".data");
 
+#if defined(CONFIG_ARCH_MVEBU)
+	#define MVEBU_MBUS_NUM_WINS 20
+	#define MVEBU_MBUS_NUM_REMAPPABLE_WINS 8
+	#define MVEBU_MBUS_WIN_CFG_OFFSET(win) armada_370_xp_mbus_win_offset(win)
+#elif defined(CONFIG_ARCH_KIRKWOOD)
+	#define MVEBU_MBUS_NUM_WINS 8
+	#define MVEBU_MBUS_NUM_REMAPPABLE_WINS 4
+	#define MVEBU_MBUS_WIN_CFG_OFFSET(win) orion5x_mbus_win_offset(win)
+#else
+	#error "No supported architecture"
+#endif
+
+static unsigned int armada_370_xp_mbus_win_offset(int win);
+static unsigned int orion5x_mbus_win_offset(int win);
+
 /*
  * Functions to manipulate the address decoding windows
  */
 
-static void mvebu_mbus_read_window(struct mvebu_mbus_state *mbus,
+static void mvebu_mbus_read_window(int win, int *enabled, u64 *base,
-				   int win, int *enabled, u64 *base,
 				   u32 *size, u8 *target, u8 *attr,
 				   u64 *remap)
 {
-	void __iomem *addr = mbus->mbuswins_base +
+	void __iomem *addr = (void __iomem *)MVEBU_CPU_WIN_BASE +
-		mbus->soc->win_cfg_offset(win);
+		MVEBU_MBUS_WIN_CFG_OFFSET(win);
 	u32 basereg = readl(addr + WIN_BASE_OFF);
 	u32 ctrlreg = readl(addr + WIN_CTRL_OFF);
 
@@ -133,7 +136,7 @@ static void mvebu_mbus_read_window(struct mvebu_mbus_state *mbus,
 		*attr = (ctrlreg & WIN_CTRL_ATTR_MASK) >> WIN_CTRL_ATTR_SHIFT;
 
 	if (remap) {
-		if (win < mbus->soc->num_remappable_wins) {
+		if (win < MVEBU_MBUS_NUM_REMAPPABLE_WINS) {
 			u32 remap_low = readl(addr + WIN_REMAP_LO_OFF);
 			u32 remap_hi  = readl(addr + WIN_REMAP_HI_OFF);
 			*remap = ((u64)remap_hi << 32) | remap_low;
@@ -143,27 +146,25 @@ static void mvebu_mbus_read_window(struct mvebu_mbus_state *mbus,
 	}
 }
 
-static void mvebu_mbus_disable_window(struct mvebu_mbus_state *mbus,
+static void mvebu_mbus_disable_window(int win)
-				      int win)
 {
 	void __iomem *addr;
 
-	addr = mbus->mbuswins_base + mbus->soc->win_cfg_offset(win);
+	addr = (void __iomem *)MVEBU_CPU_WIN_BASE + MVEBU_MBUS_WIN_CFG_OFFSET(win);
 
 	writel(0, addr + WIN_BASE_OFF);
 	writel(0, addr + WIN_CTRL_OFF);
-	if (win < mbus->soc->num_remappable_wins) {
+	if (win < MVEBU_MBUS_NUM_REMAPPABLE_WINS) {
 		writel(0, addr + WIN_REMAP_LO_OFF);
 		writel(0, addr + WIN_REMAP_HI_OFF);
 	}
 }
 
 /* Checks whether the given window number is available */
-static int mvebu_mbus_window_is_free(struct mvebu_mbus_state *mbus,
+static int mvebu_mbus_window_is_free(const int win)
-				     const int win)
 {
-	void __iomem *addr = mbus->mbuswins_base +
+	void __iomem *addr = (void __iomem *)MVEBU_CPU_WIN_BASE +
-		mbus->soc->win_cfg_offset(win);
+		MVEBU_MBUS_WIN_CFG_OFFSET(win);
 	u32 ctrl = readl(addr + WIN_CTRL_OFF);
 	return !(ctrl & WIN_CTRL_ENABLE);
 }
@@ -172,20 +173,19 @@ static int mvebu_mbus_window_is_free(struct mvebu_mbus_state *mbus,
  * Checks whether the given (base, base+size) area doesn't overlap an
  * existing region
  */
-static int mvebu_mbus_window_conflicts(struct mvebu_mbus_state *mbus,
+static int mvebu_mbus_window_conflicts(phys_addr_t base, size_t size,
-				       phys_addr_t base, size_t size,
 				       u8 target, u8 attr)
 {
 	u64 end = (u64)base + size;
 	int win;
 
-	for (win = 0; win < mbus->soc->num_wins; win++) {
+	for (win = 0; win < MVEBU_MBUS_NUM_WINS; win++) {
 		u64 wbase, wend;
 		u32 wsize;
 		u8 wtarget, wattr;
 		int enabled;
 
-		mvebu_mbus_read_window(mbus, win,
+		mvebu_mbus_read_window(win,
 				       &enabled, &wbase, &wsize,
 				       &wtarget, &wattr, NULL);
 
@@ -211,17 +211,16 @@ static int mvebu_mbus_window_conflicts(struct mvebu_mbus_state *mbus,
 	return 1;
 }
 
-static int mvebu_mbus_find_window(struct mvebu_mbus_state *mbus,
+static int mvebu_mbus_find_window(phys_addr_t base, size_t size)
-				  phys_addr_t base, size_t size)
 {
 	int win;
 
-	for (win = 0; win < mbus->soc->num_wins; win++) {
+	for (win = 0; win < MVEBU_MBUS_NUM_WINS; win++) {
 		u64 wbase;
 		u32 wsize;
 		int enabled;
 
-		mvebu_mbus_read_window(mbus, win,
+		mvebu_mbus_read_window(win,
 				       &enabled, &wbase, &wsize,
 				       NULL, NULL, NULL);
 
@@ -235,13 +234,12 @@ static int mvebu_mbus_find_window(struct mvebu_mbus_state *mbus,
 	return -ENODEV;
 }
 
-static int mvebu_mbus_setup_window(struct mvebu_mbus_state *mbus,
+static int mvebu_mbus_setup_window(int win, phys_addr_t base, size_t size,
-				   int win, phys_addr_t base, size_t size,
 				   phys_addr_t remap, u8 target,
 				   u8 attr)
 {
-	void __iomem *addr = mbus->mbuswins_base +
+	void __iomem *addr = (void __iomem *)MVEBU_CPU_WIN_BASE +
-		mbus->soc->win_cfg_offset(win);
+		MVEBU_MBUS_WIN_CFG_OFFSET(win);
 	u32 ctrl, remap_addr;
 
 	ctrl = ((size - 1) & WIN_CTRL_SIZE_MASK) |
@@ -251,7 +249,7 @@ static int mvebu_mbus_setup_window(struct mvebu_mbus_state *mbus,
 
 	writel(base & WIN_BASE_LOW, addr + WIN_BASE_OFF);
 	writel(ctrl, addr + WIN_CTRL_OFF);
-	if (win < mbus->soc->num_remappable_wins) {
+	if (win < MVEBU_MBUS_NUM_REMAPPABLE_WINS) {
 		if (remap == MVEBU_MBUS_NO_REMAP)
 			remap_addr = base;
 		else
@@ -263,26 +261,25 @@ static int mvebu_mbus_setup_window(struct mvebu_mbus_state *mbus,
 	return 0;
 }
 
-static int mvebu_mbus_alloc_window(struct mvebu_mbus_state *mbus,
+static int mvebu_mbus_alloc_window(phys_addr_t base, size_t size,
-				   phys_addr_t base, size_t size,
 				   phys_addr_t remap, u8 target,
 				   u8 attr)
 {
 	int win;
 
 	if (remap == MVEBU_MBUS_NO_REMAP) {
-		for (win = mbus->soc->num_remappable_wins;
+		for (win = MVEBU_MBUS_NUM_REMAPPABLE_WINS;
-		     win < mbus->soc->num_wins; win++)
+		     win < MVEBU_MBUS_NUM_WINS; win++)
-			if (mvebu_mbus_window_is_free(mbus, win))
+			if (mvebu_mbus_window_is_free(win))
-				return mvebu_mbus_setup_window(mbus, win, base,
+				return mvebu_mbus_setup_window(win, base,
 							       size, remap,
 							       target, attr);
 	}
 
 
-	for (win = 0; win < mbus->soc->num_wins; win++)
+	for (win = 0; win < MVEBU_MBUS_NUM_WINS; win++)
-		if (mvebu_mbus_window_is_free(mbus, win))
+		if (mvebu_mbus_window_is_free(win))
-			return mvebu_mbus_setup_window(mbus, win, base, size,
+			return mvebu_mbus_setup_window(win, base, size,
 						       remap, target, attr);
 
 	return -ENOMEM;
@@ -292,7 +289,7 @@ static int mvebu_mbus_alloc_window(struct mvebu_mbus_state *mbus,
  * SoC-specific functions and definitions
  */
 
-static unsigned int armada_370_xp_mbus_win_offset(int win)
+static unsigned int __maybe_unused armada_370_xp_mbus_win_offset(int win)
 {
 	/* The register layout is a bit annoying and the below code
 	 * tries to cope with it.
@@ -312,12 +309,12 @@ static unsigned int armada_370_xp_mbus_win_offset(int win)
 		return 0x90 + ((win - 8) << 3);
 }
 
-static unsigned int orion5x_mbus_win_offset(int win)
+static unsigned int __maybe_unused orion5x_mbus_win_offset(int win)
 {
 	return win << 4;
 }
 
-static void mvebu_mbus_default_setup_cpu_target(struct mvebu_mbus_state *mbus)
+static void mvebu_mbus_default_setup_cpu_target(void)
 {
 	int i;
 	int cs;
@@ -325,8 +322,8 @@ static void mvebu_mbus_default_setup_cpu_target(struct mvebu_mbus_state *mbus)
 	mbus_dram_info.mbus_dram_target_id = TARGET_DDR;
 
 	for (i = 0, cs = 0; i < 4; i++) {
-		u32 base = readl(mbus->sdramwins_base + DDR_BASE_CS_OFF(i));
+		u32 base = readl((void __iomem *)MVEBU_SDRAM_BASE + DDR_BASE_CS_OFF(i));
-		u32 size = readl(mbus->sdramwins_base + DDR_SIZE_CS_OFF(i));
+		u32 size = readl((void __iomem *)MVEBU_SDRAM_BASE + DDR_SIZE_CS_OFF(i));
 
 		/*
 		 * We only take care of entries for which the chip
@@ -349,26 +346,10 @@ static void mvebu_mbus_default_setup_cpu_target(struct mvebu_mbus_state *mbus)
 
 #if defined(CONFIG_ARMADA_MSYS)
 	/* Disable MBUS Err Prop - in order to avoid data aborts */
-	clrbits_le32(mbus->mbuswins_base + 0x200, BIT(8));
+	clrbits_le32((void __iomem *)MVEBU_CPU_WIN_BASE + 0x200, BIT(8));
 #endif
 }
 
-static const struct mvebu_mbus_soc_data
-armada_370_xp_mbus_data __maybe_unused = {
-	.num_wins            = 20,
-	.num_remappable_wins = 8,
-	.win_cfg_offset      = armada_370_xp_mbus_win_offset,
-	.setup_cpu_target    = mvebu_mbus_default_setup_cpu_target,
-};
-
-static const struct mvebu_mbus_soc_data
-kirkwood_mbus_data __maybe_unused = {
-	.num_wins            = 8,
-	.num_remappable_wins = 4,
-	.win_cfg_offset      = orion5x_mbus_win_offset,
-	.setup_cpu_target    = mvebu_mbus_default_setup_cpu_target,
-};
-
 /*
  * Public API of the driver
  */
@@ -382,15 +363,13 @@ int mvebu_mbus_add_window_remap_by_id(unsigned int target,
 				      phys_addr_t base, size_t size,
 				      phys_addr_t remap)
 {
-	struct mvebu_mbus_state *s = &mbus_state;
+	if (!mvebu_mbus_window_conflicts(base, size, target, attribute)) {
-
-	if (!mvebu_mbus_window_conflicts(s, base, size, target, attribute)) {
 		printf("Cannot add window '%x:%x', conflicts with another window\n",
 		       target, attribute);
 		return -EINVAL;
 	}
 
-	return mvebu_mbus_alloc_window(s, base, size, remap, target, attribute);
+	return mvebu_mbus_alloc_window(base, size, remap, target, attribute);
 }
 
 int mvebu_mbus_add_window_by_id(unsigned int target, unsigned int attribute,
@@ -404,28 +383,27 @@ int mvebu_mbus_del_window(phys_addr_t base, size_t size)
 {
 	int win;
 
-	win = mvebu_mbus_find_window(&mbus_state, base, size);
+	win = mvebu_mbus_find_window(base, size);
 	if (win < 0)
 		return win;
 
-	mvebu_mbus_disable_window(&mbus_state, win);
+	mvebu_mbus_disable_window(win);
 	return 0;
 }
 
 #ifndef CONFIG_ARCH_KIRKWOOD
-static void mvebu_mbus_get_lowest_base(struct mvebu_mbus_state *mbus,
+static void mvebu_mbus_get_lowest_base(phys_addr_t *base)
-				       phys_addr_t *base)
 {
 	int win;
 	*base = 0xffffffff;
 
-	for (win = 0; win < mbus->soc->num_wins; win++) {
+	for (win = 0; win < MVEBU_MBUS_NUM_WINS; win++) {
 		u64 wbase;
 		u32 wsize;
 		u8 wtarget, wattr;
 		int enabled;
 
-		mvebu_mbus_read_window(mbus, win,
+		mvebu_mbus_read_window(win,
 				       &enabled, &wbase, &wsize,
 				       &wtarget, &wattr, NULL);
 
@@ -437,14 +415,14 @@ static void mvebu_mbus_get_lowest_base(struct mvebu_mbus_state *mbus,
 	}
 }
 
-static void mvebu_config_mbus_bridge(struct mvebu_mbus_state *mbus)
+static void mvebu_config_mbus_bridge(void)
 {
 	phys_addr_t base;
 	u32 val;
 	u32 size;
 
 	/* Set MBUS bridge base/ctrl */
-	mvebu_mbus_get_lowest_base(&mbus_state, &base);
+	mvebu_mbus_get_lowest_base(&base);
 
 	size = 0xffffffff - base + 1;
 	if (!is_power_of_2(size)) {
@@ -461,10 +439,9 @@ static void mvebu_config_mbus_bridge(struct mvebu_mbus_state *mbus)
 }
 #endif
 
-int mbus_dt_setup_win(struct mvebu_mbus_state *mbus,
+int mbus_dt_setup_win(u32 base, u32 size, u8 target, u8 attr)
-		      u32 base, u32 size, u8 target, u8 attr)
 {
-	if (!mvebu_mbus_window_conflicts(mbus, base, size, target, attr)) {
+	if (!mvebu_mbus_window_conflicts(base, size, target, attr)) {
 		printf("Cannot add window '%04x:%04x', conflicts with another window\n",
 		       target, attr);
 		return -EBUSY;
@@ -474,8 +451,8 @@ int mbus_dt_setup_win(struct mvebu_mbus_state *mbus,
 	 * In U-Boot we first try to add the mbus window to the remap windows.
 	 * If this fails, lets try to add the windows to the non-remap windows.
 	 */
-	if (mvebu_mbus_alloc_window(mbus, base, size, base, target, attr)) {
+	if (mvebu_mbus_alloc_window(base, size, base, target, attr)) {
-		if (mvebu_mbus_alloc_window(mbus, base, size,
+		if (mvebu_mbus_alloc_window(base, size,
 					    MVEBU_MBUS_NO_REMAP, target, attr))
 			return -ENOMEM;
 	}
@@ -486,7 +463,7 @@ int mbus_dt_setup_win(struct mvebu_mbus_state *mbus,
 	 * is called. Since it may get called from the board code in
 	 * later boot stages as well.
 	 */
-	mvebu_config_mbus_bridge(mbus);
+	mvebu_config_mbus_bridge();
 #endif
 
 	return 0;
@@ -498,20 +475,10 @@ int mvebu_mbus_probe(struct mbus_win windows[], int count)
 	int ret;
 	int i;
 
-#if defined(CONFIG_ARCH_KIRKWOOD)
+	for (win = 0; win < MVEBU_MBUS_NUM_WINS; win++)
-	mbus_state.soc = &kirkwood_mbus_data;
+		mvebu_mbus_disable_window(win);
-#endif
-#if defined(CONFIG_ARCH_MVEBU)
-	mbus_state.soc = &armada_370_xp_mbus_data;
-#endif
 
-	mbus_state.mbuswins_base = (void __iomem *)MVEBU_CPU_WIN_BASE;
+	mvebu_mbus_default_setup_cpu_target();
-	mbus_state.sdramwins_base = (void __iomem *)MVEBU_SDRAM_BASE;
-
-	for (win = 0; win < mbus_state.soc->num_wins; win++)
-		mvebu_mbus_disable_window(&mbus_state, win);
-
-	mbus_state.soc->setup_cpu_target(&mbus_state);
 
 	/* Setup statically declared windows in the DT */
 	for (i = 0; i < count; i++) {
@@ -522,7 +489,7 @@ int mvebu_mbus_probe(struct mbus_win windows[], int count)
 		attr = windows[i].attr;
 		base = windows[i].base;
 		size = windows[i].size;
-		ret = mbus_dt_setup_win(&mbus_state, base, size, target, attr);
+		ret = mbus_dt_setup_win(base, size, target, attr);
 		if (ret < 0)
 			return ret;
 	}

arch/arm/mach-mvebu/spl.c

@@ -299,6 +299,19 @@ int board_return_to_bootrom(struct spl_image_info *spl_image,
 	hang();
 }
 
+/*
+ * SPI0 CS0 Flash is mapped to address range 0xD4000000 - 0xD7FFFFFF by BootROM.
+ * Proper U-Boot removes this direct mapping. So it is available only in SPL.
+ */
+#if defined(CONFIG_SPL_ENV_IS_IN_SPI_FLASH) && \
+    CONFIG_ENV_SPI_BUS == 0 && CONFIG_ENV_SPI_CS == 0 && \
+    CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE <= 64*1024*1024
+void *env_sf_get_env_addr(void)
+{
+	return (void *)0xD4000000 + CONFIG_ENV_OFFSET;
+}
+#endif
+
 void board_init_f(ulong dummy)
 {
 	int ret;

board/CZ.NIC/turris_mox/turris_mox.c

@@ -821,6 +821,11 @@ int ft_board_setup(void *blob, struct bd_info *bd)
 						 "sgmii");
 			if (res < 0)
 				return res;
+
+			res = fdt_setprop_string(blob, node, "label",
+						 "sfp");
+			if (res < 0)
+				return res;
 		}
 
 		res = fdt_status_okay_by_compatible(blob, "cznic,moxtet-gpio");

board/CZ.NIC/turris_omnia/turris_omnia.c

@@ -21,6 +21,7 @@
 #include <dm/uclass.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <fdt_support.h>
+#include <hexdump.h>
 #include <time.h>
 #include <linux/bitops.h>
 #include <linux/delay.h>
@@ -61,7 +62,9 @@ DECLARE_GLOBAL_DATA_PTR;
 enum mcu_commands {
 	CMD_GET_STATUS_WORD	= 0x01,
 	CMD_GET_RESET		= 0x09,
+	CMD_GET_FW_VERSION_APP	= 0x0a,
 	CMD_WATCHDOG_STATE	= 0x0b,
+	CMD_GET_FW_VERSION_BOOT	= 0x0e,
 
 	/* available if STS_FEATURES_SUPPORTED bit set in status word */
 	CMD_GET_FEATURES	= 0x10,
@@ -282,16 +285,6 @@ static bool omnia_detect_wwan_usb3(const char *wwan_slot)
 	return false;
 }
 
-void *env_sf_get_env_addr(void)
-{
-	/* SPI Flash is mapped to address 0xD4000000 only in SPL */
-#ifdef CONFIG_SPL_BUILD
-	return (void *)0xD4000000 + CONFIG_ENV_OFFSET;
-#else
-	return NULL;
-#endif
-}
-
 int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
 {
 #ifdef CONFIG_SPL_ENV_SUPPORT
@@ -428,6 +421,38 @@ static const char * const omnia_get_mcu_type(void)
 	return mcu_types[stsword & STS_MCU_TYPE_MASK];
 }
 
+static const char * const omnia_get_mcu_version(void)
+{
+	static char version[82];
+	u8 version_app[20];
+	u8 version_boot[20];
+	int ret;
+
+	ret = omnia_mcu_read(CMD_GET_FW_VERSION_APP, &version_app, sizeof(version_app));
+	if (ret)
+		return "unknown";
+
+	ret = omnia_mcu_read(CMD_GET_FW_VERSION_BOOT, &version_boot, sizeof(version_boot));
+	if (ret)
+		return "unknown";
+
+	/*
+	 * If git commits of MCU bootloader and MCU application are same then
+	 * show version only once. If they are different then show both commits.
+	 */
+	if (!memcmp(version_app, version_boot, 20)) {
+		bin2hex(version, version_app, 20);
+		version[40] = '\0';
+	} else {
+		bin2hex(version, version_boot, 20);
+		version[40] = '/';
+		bin2hex(version + 41, version_app, 20);
+		version[81] = '\0';
+	}
+
+	return version;
+}
+
 /*
  * Define the DDR layout / topology here in the board file. This will
  * be used by the DDR3 init code in the SPL U-Boot version to configure
@@ -944,6 +969,7 @@ int show_board_info(void)
 	err = turris_atsha_otp_get_serial_number(&version_num, &serial_num);
 	printf("Model: Turris Omnia\n");
 	printf("  MCU type: %s\n", omnia_get_mcu_type());
+	printf("  MCU version: %s\n", omnia_get_mcu_version());
 	printf("  RAM size: %i MiB\n", omnia_get_ram_size_gb() * 1024);
 	if (err)
 		printf("  Serial Number: unknown\n");

board/Synology/ds109/ds109.c

@@ -10,6 +10,7 @@
 #include <miiphy.h>
 #include <net.h>
 #include <asm/global_data.h>
+#include <asm/io.h>
 #include <asm/setup.h>
 #include <asm/arch/cpu.h>
 #include <asm/arch/soc.h>

board/alliedtelesis/x530/x530.c

@@ -109,7 +109,7 @@ int board_init(void)
 	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
 
 	/* window for NVS */
-	mbus_dt_setup_win(&mbus_state, CONFIG_NVS_LOCATION, CONFIG_NVS_SIZE,
+	mbus_dt_setup_win(CONFIG_NVS_LOCATION, CONFIG_NVS_SIZE,
 			  CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_DEV_CS1);
 
 	/* DEV_READYn is not needed for NVS, ignore it when accessing CS1 */

board/buffalo/lsxl/README

@@ -31,8 +31,8 @@ generated if no valid address could be loaded from the environment variable
 'ethaddr' and a DHCP request is sent. After a successful DHCP response is
 received, the network settings are configured and the ncip is unset. Thus
 all netconsole packets are broadcasted and you can use the netconsole to
-access board from any host within the network segment. To determine the IP
+access the board from any host within the network segment. To determine the
-address assigned to the board, you either have to sniff the traffic or
+IP address assigned to the board, you either have to sniff the traffic or
 check the logs/leases of your DHCP server.
 
 The resuce mode is selected by holding the push button for at least one
@@ -42,41 +42,43 @@ the resuce mode is enabled, thus providing a visual feedback.
 Pressing the same button for at least 10 seconds on power-up will erase the
 environment and reset the board. In this case the visual indication will
 be:
-- blinking blue, for about one second
+- blue, for about one second
-- solid amber, for about nine seconds
+- amber, for about nine seconds
-- blinking amber, until you release the button
+- red, until you release the button
 
 This ensures, that you still can recover a device with a broken
 environment by first erasing the environment and then entering the rescue
 mode.
 
 Once the rescue mode is started, use the ncb binary from the tools/
-directory to access your board. There is a helper script named
+directory to access your board.
-'restore_env' to save your changes. It unsets all the network variables
-which were set by the rescue mode, saves your changes and then resets the
-board.
 
 The common use case for this is setting a MAC address. Let us assume you
-have an empty environment, the board comes up with the amber LED blinking.
+have an empty environment, the board comes up with the amber LED turned on.
 Then you enter the rescue mode, connect to the board with the ncb tool and
 use the following commands to set your MAC address:
 
-  setenv ethaddr 00:00:00:00:00:00
+  setenv -f ethaddr 00:00:00:00:00:00
-  run restore_env
+  saveenv
+  reset
 
 Of course you need to replace the 00:00:00:00:00:00 with your valid MAC
 address, which can be found on a sticker on the bottom of your box.
 
+You cannot store the network console setting in the environment. On reset
+it is automatically restored to serial. Therefore, you have to use the
+push-button to enter resuce mode again.
+
 
 Status LED
 ----------
-blinking blue
+blue
   Bootloader is running normally.
 
-blinking amber
+amber
   No ethaddr set. Use the `Rescue Mode` to set one.
 
-blinking red
+red
   Something bad happend during loading the operating system.
 
 The default behavior of the linux kernel is to turn on the blue LED. So if

board/buffalo/lsxl/lsxl.c

@@ -9,21 +9,18 @@
 
 #include <common.h>
 #include <bootstage.h>
+#include <button.h>
 #include <command.h>
 #include <env.h>
-#include <env_internal.h>
 #include <init.h>
-#include <net.h>
+#include <led.h>
-#include <malloc.h>
+#include <power/regulator.h>
-#include <netdev.h>
-#include <miiphy.h>
 #include <spi.h>
 #include <spi_flash.h>
-#include <asm/arch/soc.h>
 #include <asm/arch/cpu.h>
 #include <asm/arch/mpp.h>
-#include <asm/arch/gpio.h>
 #include <asm/global_data.h>
+#include <asm/io.h>
 #include <linux/delay.h>
 
 #include "lsxl.h"
@@ -45,12 +42,10 @@
  * Additionally, the bootsource is set to 'rescue'.
  */
 
-#ifndef CONFIG_ENV_OVERWRITE
-# error "You need to set CONFIG_ENV_OVERWRITE"
-#endif
-
 DECLARE_GLOBAL_DATA_PTR;
 
+static bool force_rescue_mode;
+
 int board_early_init_f(void)
 {
 	/*
@@ -125,48 +120,43 @@ int board_early_init_f(void)
 	return 0;
 }
 
-#define LED_OFF             0
+enum {
-#define LED_ALARM_ON        1
+	LSXL_LED_OFF,
-#define LED_ALARM_BLINKING  2
+	LSXL_LED_ALARM,
-#define LED_POWER_ON        3
+	LSXL_LED_POWER,
-#define LED_POWER_BLINKING  4
+	LSXL_LED_INFO,
-#define LED_INFO_ON         5
+};
-#define LED_INFO_BLINKING   6
 
-static void __set_led(int blink_alarm, int blink_info, int blink_power,
+static void __set_led(int alarm, int info, int power)
-		int value_alarm, int value_info, int value_power)
 {
-	kw_gpio_set_blink(GPIO_ALARM_LED, blink_alarm);
+	struct udevice *led;
-	kw_gpio_set_blink(GPIO_INFO_LED, blink_info);
+	int ret;
-	kw_gpio_set_blink(GPIO_POWER_LED, blink_power);
+
-	kw_gpio_set_value(GPIO_ALARM_LED, value_alarm);
+	ret = led_get_by_label("lsxl:red:alarm", &led);
-	kw_gpio_set_value(GPIO_INFO_LED, value_info);
+	if (!ret)
-	kw_gpio_set_value(GPIO_POWER_LED, value_power);
+		led_set_state(led, alarm);
+	ret = led_get_by_label("lsxl:amber:info", &led);
+	if (!ret)
+		led_set_state(led, info);
+	ret = led_get_by_label("lsxl:blue:power", &led);
+	if (!ret)
+		led_set_state(led, power);
 }
 
 static void set_led(int state)
 {
 	switch (state) {
-	case LED_OFF:
+	case LSXL_LED_OFF:
-		__set_led(0, 0, 0, 1, 1, 1);
+		__set_led(0, 0, 0);
 		break;
-	case LED_ALARM_ON:
+	case LSXL_LED_ALARM:
-		__set_led(0, 0, 0, 0, 1, 1);
+		__set_led(1, 0, 0);
 		break;
-	case LED_ALARM_BLINKING:
+	case LSXL_LED_INFO:
-		__set_led(1, 0, 0, 1, 1, 1);
+		__set_led(0, 1, 0);
 		break;
-	case LED_INFO_ON:
+	case LSXL_LED_POWER:
-		__set_led(0, 0, 0, 1, 0, 1);
+		__set_led(0, 0, 1);
-		break;
-	case LED_INFO_BLINKING:
-		__set_led(0, 1, 0, 1, 1, 1);
-		break;
-	case LED_POWER_ON:
-		__set_led(0, 0, 0, 1, 1, 0);
-		break;
-	case LED_POWER_BLINKING:
-		__set_led(0, 0, 1, 1, 1, 1);
 		break;
 	}
 }
@@ -176,33 +166,56 @@ int board_init(void)
 	/* address of boot parameters */
 	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
 
-	set_led(LED_POWER_BLINKING);
+	set_led(LSXL_LED_POWER);
 
 	return 0;
 }
 
-#ifdef CONFIG_MISC_INIT_R
 static void check_power_switch(void)
 {
-	if (kw_gpio_get_value(GPIO_POWER_SWITCH)) {
+	struct udevice *power_button, *hdd_power, *usb_power;
-		/* turn off fan, HDD and USB power */
+	int ret;
-		kw_gpio_set_value(GPIO_HDD_POWER, 0);
+
-		kw_gpio_set_value(GPIO_USB_VBUS, 0);
+	ret = button_get_by_label("Power-on Switch", &power_button);
-		kw_gpio_set_value(GPIO_FAN_HIGH, 1);
+	if (ret)
-		kw_gpio_set_value(GPIO_FAN_LOW, 1);
+		goto err;
-		set_led(LED_OFF);
+
+	ret = regulator_get_by_platname("HDD Power", &hdd_power);
+	if (ret)
+		goto err;
+
+	ret = regulator_get_by_platname("USB Power", &usb_power);
+	if (ret)
+		goto err;
+
+	if (button_get_state(power_button) == BUTTON_OFF) {
+		ret = regulator_set_enable(hdd_power, false);
+		if (ret)
+			goto err;
+		ret = regulator_set_enable(usb_power, false);
+		if (ret)
+			goto err;
+		/* TODO: fan off */
+		set_led(LSXL_LED_OFF);
 
 		/* loop until released */
-		while (kw_gpio_get_value(GPIO_POWER_SWITCH))
+		while (button_get_state(power_button) == BUTTON_OFF)
 			;
 
 		/* turn power on again */
-		kw_gpio_set_value(GPIO_HDD_POWER, 1);
+		ret = regulator_set_enable(hdd_power, true);
-		kw_gpio_set_value(GPIO_USB_VBUS, 1);
+		if (ret)
-		kw_gpio_set_value(GPIO_FAN_HIGH, 0);
+			goto err;
-		kw_gpio_set_value(GPIO_FAN_LOW, 0);
+		ret = regulator_set_enable(usb_power, true);
-		set_led(LED_POWER_BLINKING);
+		if (ret)
-	}
+			goto err;
+		/* TODO: fan on */
+		set_led(LSXL_LED_POWER);
+	};
+
+	return;
+err:
+	printf("error in %s\n", __func__);
 }
 
 void check_enetaddr(void)
@@ -211,7 +224,7 @@ void check_enetaddr(void)
 
 	if (!eth_env_get_enetaddr("ethaddr", enetaddr)) {
 		/* signal unset/invalid ethaddr to user */
-		set_led(LED_INFO_BLINKING);
+		set_led(LSXL_LED_INFO);
 	}
 }
 
@@ -239,17 +252,24 @@ static void rescue_mode(void)
 
 static void check_push_button(void)
 {
+	struct udevice *func_button;
 	int i = 0;
 
-	while (!kw_gpio_get_value(GPIO_FUNC_BUTTON)) {
+	int ret;
+
+	ret = button_get_by_label("Function Button", &func_button);
+	if (ret)
+		goto err;
+
+	while (button_get_state(func_button) == BUTTON_ON) {
 		udelay(100000);
 		i++;
 
 		if (i == 10)
-			set_led(LED_INFO_ON);
+			set_led(LSXL_LED_INFO);
 
 		if (i >= 100) {
-			set_led(LED_INFO_BLINKING);
+			set_led(LSXL_LED_ALARM);
 			break;
 		}
 	}
@@ -257,18 +277,29 @@ static void check_push_button(void)
 	if (i >= 100)
 		erase_environment();
 	else if (i >= 10)
-		rescue_mode();
+		force_rescue_mode = true;
+
+	return;
+err:
+	printf("error in %s\n", __func__);
+}
+
+int board_early_init_r(void)
+{
+	check_push_button();
+
+	return 0;
 }
 
 int misc_init_r(void)
 {
 	check_power_switch();
 	check_enetaddr();
-	check_push_button();
+	if (force_rescue_mode)
+		rescue_mode();
 
 	return 0;
 }
-#endif
 
 #if CONFIG_IS_ENABLED(BOOTSTAGE)
 void show_boot_progress(int progress)
@@ -280,6 +311,6 @@ void show_boot_progress(int progress)
 	if (progress == -BOOTSTAGE_ID_NET_LOADED)
 		return;
 
-	set_led(LED_ALARM_BLINKING);
+	set_led(LSXL_LED_ALARM);
 }
 #endif

board/maxbcm/maxbcm.c

@@ -112,13 +112,13 @@ int board_early_init_f(void)
 	/*
 	 * Setup some board specific mbus address windows
 	 */
-	mbus_dt_setup_win(&mbus_state, DEV_CS0_BASE, 16 << 20,
+	mbus_dt_setup_win(DEV_CS0_BASE, 16 << 20,
 			  CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_DEV_CS0);
-	mbus_dt_setup_win(&mbus_state, DEV_CS1_BASE, 16 << 20,
+	mbus_dt_setup_win(DEV_CS1_BASE, 16 << 20,
 			  CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_DEV_CS1);
-	mbus_dt_setup_win(&mbus_state, DEV_CS2_BASE, 16 << 20,
+	mbus_dt_setup_win(DEV_CS2_BASE, 16 << 20,
 			  CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_DEV_CS2);
-	mbus_dt_setup_win(&mbus_state, DEV_CS3_BASE, 16 << 20,
+	mbus_dt_setup_win(DEV_CS3_BASE, 16 << 20,
 			  CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_DEV_CS3);
 
 	return 0;

board/theadorable/theadorable.c

@@ -208,9 +208,9 @@ int board_init(void)
 	 * Map SPI devices via MBUS so that they can be accessed via
 	 * the SPI direct access mode
 	 */
-	mbus_dt_setup_win(&mbus_state, SPI_BUS0_DEV1_BASE, SPI_BUS0_DEV1_SIZE,
+	mbus_dt_setup_win(SPI_BUS0_DEV1_BASE, SPI_BUS0_DEV1_SIZE,
 			  CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_SPI0_CS1);
-	mbus_dt_setup_win(&mbus_state, SPI_BUS1_DEV2_BASE, SPI_BUS0_DEV1_SIZE,
+	mbus_dt_setup_win(SPI_BUS1_DEV2_BASE, SPI_BUS0_DEV1_SIZE,
 			  CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_SPI1_CS2);
 
 	/*

board/zyxel/nsa310s/MAINTAINERS

@@ -1,5 +1,4 @@
 NSA310S BOARD
-M:	Gerald Kerma <dreagle@doukki.net>
 M:	Tony Dinh <mibodhi@gmail.com>
 M:	Luka Perkov <luka.perkov@sartura.hr>
 S:	Maintained

configs/lschlv2_defconfig

@@ -3,39 +3,44 @@ CONFIG_SKIP_LOWLEVEL_INIT=y
 CONFIG_SYS_DCACHE_OFF=y
 CONFIG_ARCH_CPU_INIT=y
 CONFIG_ARCH_KIRKWOOD=y
+CONFIG_SUPPORT_PASSING_ATAGS=y
+CONFIG_CMDLINE_TAG=y
+CONFIG_INITRD_TAG=y
 CONFIG_SYS_KWD_CONFIG="board/buffalo/lsxl/kwbimage-lschl.cfg"
 CONFIG_SYS_TEXT_BASE=0x600000
-CONFIG_SYS_MALLOC_F_LEN=0x400
 CONFIG_NR_DRAM_BANKS=2
 CONFIG_TARGET_LSXL=y
 CONFIG_ENV_SIZE=0x10000
 CONFIG_ENV_OFFSET=0x70000
 CONFIG_ENV_SECT_SIZE=0x10000
+CONFIG_DM_GPIO=y
 CONFIG_DEFAULT_DEVICE_TREE="kirkwood-lschlv2"
 CONFIG_IDENT_STRING=" LS-CHLv2"
 CONFIG_SYS_LOAD_ADDR=0x800000
 CONFIG_DISTRO_DEFAULTS=y
 CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x5ff000
-CONFIG_API=y
+CONFIG_HAS_BOARD_SIZE_LIMIT=y
+CONFIG_BOARD_SIZE_LIMIT=393216
+# CONFIG_BOOTSTD is not set
 CONFIG_SHOW_BOOT_PROGRESS=y
 CONFIG_BOOTDELAY=3
 CONFIG_USE_BOOTARGS=y
 CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/sda2"
 CONFIG_BOOTCOMMAND="run bootcmd_${bootsource}"
-CONFIG_USE_PREBOOT=y
+CONFIG_DEFAULT_FDT_FILE="kirkwood-lschlv2.dtb"
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 CONFIG_SYS_CONSOLE_INFO_QUIET=y
 # CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_MISC_INIT_R=y
 CONFIG_SYS_MAXARGS=32
 # CONFIG_CMD_FLASH is not set
 CONFIG_CMD_SATA=y
 CONFIG_CMD_SPI=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
+# CONFIG_CMD_BUTTON is not set
+# CONFIG_CMD_LED is not set
+CONFIG_CMD_REGULATOR=y
 CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_NET_RANDOM_ETHADDR=y
@@ -46,17 +51,27 @@ CONFIG_SATA_MV=y
 CONFIG_SYS_SATA_MAX_DEVICE=1
 CONFIG_LBA48=y
 CONFIG_SYS_64BIT_LBA=y
-CONFIG_KIRKWOOD_GPIO=y
+CONFIG_BUTTON=y
+CONFIG_BUTTON_GPIO=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
 # CONFIG_MMC is not set
 CONFIG_MTD=y
 CONFIG_DM_SPI_FLASH=y
 CONFIG_SF_DEFAULT_SPEED=25000000
 CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_DM_ETH=y
+CONFIG_DM_MDIO=y
 CONFIG_MVGBE=y
 CONFIG_MII=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_SERIAL=y
 CONFIG_SYS_NS16550=y
 CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_KIRKWOOD_SPI=y
+CONFIG_TIMER=y
+CONFIG_ORION_TIMER=y
 CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y

configs/lsxhl_defconfig

@@ -3,40 +3,45 @@ CONFIG_SKIP_LOWLEVEL_INIT=y
 CONFIG_SYS_DCACHE_OFF=y
 CONFIG_ARCH_CPU_INIT=y
 CONFIG_ARCH_KIRKWOOD=y
+CONFIG_SUPPORT_PASSING_ATAGS=y
+CONFIG_CMDLINE_TAG=y
+CONFIG_INITRD_TAG=y
 CONFIG_SYS_KWD_CONFIG="board/buffalo/lsxl/kwbimage-lsxhl.cfg"
 CONFIG_SYS_TEXT_BASE=0x600000
-CONFIG_SYS_MALLOC_F_LEN=0x400
 CONFIG_NR_DRAM_BANKS=2
 CONFIG_TARGET_LSXL=y
 CONFIG_LSXHL=y
 CONFIG_ENV_SIZE=0x10000
 CONFIG_ENV_OFFSET=0x70000
 CONFIG_ENV_SECT_SIZE=0x10000
+CONFIG_DM_GPIO=y
 CONFIG_DEFAULT_DEVICE_TREE="kirkwood-lsxhl"
 CONFIG_IDENT_STRING=" LS-XHL"
 CONFIG_SYS_LOAD_ADDR=0x800000
 CONFIG_DISTRO_DEFAULTS=y
 CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x5ff000
-CONFIG_API=y
+CONFIG_HAS_BOARD_SIZE_LIMIT=y
+CONFIG_BOARD_SIZE_LIMIT=393216
+# CONFIG_BOOTSTD is not set
 CONFIG_SHOW_BOOT_PROGRESS=y
 CONFIG_BOOTDELAY=3
 CONFIG_USE_BOOTARGS=y
 CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/sda2"
 CONFIG_BOOTCOMMAND="run bootcmd_${bootsource}"
-CONFIG_USE_PREBOOT=y
+CONFIG_DEFAULT_FDT_FILE="kirkwood-lsxhl.dtb"
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 CONFIG_SYS_CONSOLE_INFO_QUIET=y
 # CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_MISC_INIT_R=y
 CONFIG_SYS_MAXARGS=32
 # CONFIG_CMD_FLASH is not set
 CONFIG_CMD_SATA=y
 CONFIG_CMD_SPI=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
+# CONFIG_CMD_BUTTON is not set
+# CONFIG_CMD_LED is not set
+CONFIG_CMD_REGULATOR=y
 CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_NET_RANDOM_ETHADDR=y
@@ -47,17 +52,27 @@ CONFIG_SATA_MV=y
 CONFIG_SYS_SATA_MAX_DEVICE=1
 CONFIG_LBA48=y
 CONFIG_SYS_64BIT_LBA=y
-CONFIG_KIRKWOOD_GPIO=y
+CONFIG_BUTTON=y
+CONFIG_BUTTON_GPIO=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
 # CONFIG_MMC is not set
 CONFIG_MTD=y
 CONFIG_DM_SPI_FLASH=y
 CONFIG_SF_DEFAULT_SPEED=25000000
 CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_DM_ETH=y
+CONFIG_DM_MDIO=y
 CONFIG_MVGBE=y
 CONFIG_MII=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_SERIAL=y
 CONFIG_SYS_NS16550=y
 CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_KIRKWOOD_SPI=y
+CONFIG_TIMER=y
+CONFIG_ORION_TIMER=y
 CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y

configs/nsa310s_defconfig

@@ -4,6 +4,9 @@ CONFIG_SYS_DCACHE_OFF=y
 CONFIG_ARCH_CPU_INIT=y
 CONFIG_SYS_THUMB_BUILD=y
 CONFIG_ARCH_KIRKWOOD=y
+CONFIG_SUPPORT_PASSING_ATAGS=y
+CONFIG_CMDLINE_TAG=y
+CONFIG_INITRD_TAG=y
 CONFIG_SYS_KWD_CONFIG="board/zyxel/nsa310s/kwbimage.cfg"
 CONFIG_SYS_TEXT_BASE=0x600000
 CONFIG_SYS_MALLOC_F_LEN=0x400
@@ -15,34 +18,24 @@ CONFIG_DEFAULT_DEVICE_TREE="kirkwood-nsa310s"
 CONFIG_SYS_PROMPT="NSA310s> "
 CONFIG_IDENT_STRING="\nZyXEL NSA310S/320S 1/2-Bay Power Media Server"
 CONFIG_SYS_LOAD_ADDR=0x800000
+CONFIG_DISTRO_DEFAULTS=y
 CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
 CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000
 CONFIG_BOOTDELAY=3
-CONFIG_USE_BOOTCOMMAND=y
-CONFIG_BOOTCOMMAND="setenv bootargs ${console} ${mtdparts} ${bootargs_root}; ubi part root; ubifsmount ubi:rootfs; ubifsload 0x800000 ${kernel}; ubifsload 0x700000 ${fdt}; ubifsumount; fdt addr 0x700000; fdt resize; fdt chosen; bootz 0x800000 - 0x700000"
 CONFIG_USE_PREBOOT=y
 # CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_HUSH_PARSER=y
 CONFIG_SYS_MAXARGS=32
 CONFIG_SYS_PBSIZE=1050
-CONFIG_CMD_BOOTZ=y
 # CONFIG_CMD_FLASH is not set
 CONFIG_CMD_NAND=y
 CONFIG_CMD_SATA=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
 CONFIG_CMD_JFFS2=y
 CONFIG_CMD_MTDPARTS=y
 CONFIG_MTDIDS_DEFAULT="nand0=orion_nand"
 CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:0xe0000@0x0(uboot),0x20000@0xe0000(uboot_env),0x100000@0x100000(second_stage_uboot),-@0x200000(root)"
 CONFIG_CMD_UBI=y
-CONFIG_ISO_PARTITION=y
 CONFIG_OF_CONTROL=y
 CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_NAND=y
@@ -64,6 +57,6 @@ CONFIG_MII=y
 CONFIG_SYS_NS16550=y
 CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_STORAGE=y
+CONFIG_UBIFS_SILENCE_MSG=y
 CONFIG_LZMA=y
 CONFIG_BZIP2=y

configs/pogo_v4_defconfig

@@ -4,6 +4,9 @@ CONFIG_SYS_DCACHE_OFF=y
 CONFIG_ARCH_CPU_INIT=y
 CONFIG_SYS_THUMB_BUILD=y
 CONFIG_ARCH_KIRKWOOD=y
+CONFIG_SUPPORT_PASSING_ATAGS=y
+CONFIG_CMDLINE_TAG=y
+CONFIG_INITRD_TAG=y
 CONFIG_SYS_KWD_CONFIG="board/cloudengines/pogo_v4/kwbimage.cfg"
 CONFIG_SYS_TEXT_BASE=0x600000
 CONFIG_SYS_MALLOC_F_LEN=0x400
@@ -14,22 +17,23 @@ CONFIG_DEFAULT_DEVICE_TREE="kirkwood-pogoplug-series-4"
 CONFIG_SYS_PROMPT="Pogo_V4> "
 CONFIG_IDENT_STRING="\nPogoplug V4"
 CONFIG_SYS_LOAD_ADDR=0x800000
+CONFIG_LTO=y
+CONFIG_DISTRO_DEFAULTS=y
 CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
 CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000
 CONFIG_BOOTSTAGE=y
 CONFIG_SHOW_BOOT_PROGRESS=y
 CONFIG_BOOTDELAY=10
-CONFIG_USE_BOOTCOMMAND=y
-CONFIG_BOOTCOMMAND="setenv bootargs ${bootargs_console}; run bootcmd_usb; bootm 0x00800000 0x01100000 0x2c00000"
 CONFIG_USE_PREBOOT=y
 CONFIG_BOARD_LATE_INIT=y
-CONFIG_HUSH_PARSER=y
 CONFIG_SYS_MAXARGS=32
 CONFIG_SYS_PBSIZE=1050
-CONFIG_CMD_BOOTZ=y
 # CONFIG_BOOTM_PLAN9 is not set
 # CONFIG_BOOTM_RTEMS is not set
 # CONFIG_BOOTM_VXWORKS is not set
+# CONFIG_CMD_ELF is not set
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_XIMG is not set
 # CONFIG_CMD_FLASH is not set
 CONFIG_CMD_MMC=y
 CONFIG_CMD_MTD=y
@@ -37,22 +41,14 @@ CONFIG_CMD_NAND=y
 CONFIG_CMD_PCI=y
 CONFIG_CMD_SATA=y
 CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
 CONFIG_CMD_SNTP=y
 CONFIG_CMD_DNS=y
-CONFIG_CMD_EXT2=y
+# CONFIG_CMD_BLOCK_CACHE is not set
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
 CONFIG_CMD_JFFS2=y
 CONFIG_CMD_MTDPARTS=y
 CONFIG_MTDIDS_DEFAULT="nand0=orion_nand"
 CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)"
 CONFIG_CMD_UBI=y
-CONFIG_ISO_PARTITION=y
-CONFIG_EFI_PARTITION=y
 CONFIG_PARTITION_TYPE_GUID=y
 CONFIG_OF_CONTROL=y
 CONFIG_ENV_OVERWRITE=y
@@ -62,6 +58,7 @@ CONFIG_NET_RANDOM_ETHADDR=y
 CONFIG_NETCONSOLE=y
 CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
 CONFIG_DM=y
+# CONFIG_DM_WARN is not set
 CONFIG_SATA_MV=y
 CONFIG_SYS_SATA_MAX_DEVICE=1
 CONFIG_LBA48=y
@@ -83,6 +80,6 @@ CONFIG_USB=y
 CONFIG_USB_XHCI_HCD=y
 CONFIG_USB_XHCI_PCI=y
 CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_STORAGE=y
 CONFIG_JFFS2_LZO=y
 CONFIG_JFFS2_NAND=y
+CONFIG_UBIFS_SILENCE_MSG=y

drivers/button/Kconfig

@@ -20,6 +20,7 @@ config BUTTON_ADC
 config BUTTON_GPIO
 	bool "Button gpio"
 	depends on BUTTON
+	depends on DM_GPIO
 	help
 	  Enable support for buttons which are connected to GPIO lines. These
 	  GPIOs may be on the SoC or some other device which provides GPIOs.

drivers/timer/Kconfig

@@ -194,6 +194,12 @@ config OMAP_TIMER
 	help
 	  Select this to enable an timer for Omap devices.
 
+config ORION_TIMER
+	bool "Orion timer support"
+	depends on TIMER
+	help
+	  Select this to enable an timer for Orion devices.
+
 config RISCV_TIMER
 	bool "RISC-V timer support"
 	depends on TIMER && RISCV

drivers/timer/Makefile

@@ -17,6 +17,7 @@ obj-$(CONFIG_MPC83XX_TIMER) += mpc83xx_timer.o
 obj-$(CONFIG_NOMADIK_MTU_TIMER)	+= nomadik-mtu-timer.o
 obj-$(CONFIG_NPCM_TIMER)        += npcm-timer.o
 obj-$(CONFIG_OMAP_TIMER)	+= omap-timer.o
+obj-$(CONFIG_ORION_TIMER)	+= orion-timer.o
 obj-$(CONFIG_RENESAS_OSTM_TIMER) += ostm_timer.o
 obj-$(CONFIG_RISCV_TIMER) += riscv_timer.o
 obj-$(CONFIG_ROCKCHIP_TIMER) += rockchip_timer.o

drivers/timer/orion-timer.c

@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: GPL-2.0+
+#include <asm/io.h>
+#include <common.h>
+#include <dm/device.h>
+#include <dm/fdtaddr.h>
+#include <timer.h>
+
+#define TIMER_CTRL		0x00
+#define TIMER0_EN		BIT(0)
+#define TIMER0_RELOAD_EN	BIT(1)
+#define TIMER0_RELOAD		0x10
+#define TIMER0_VAL		0x14
+
+struct orion_timer_priv {
+	void *base;
+};
+
+static uint64_t orion_timer_get_count(struct udevice *dev)
+{
+	struct orion_timer_priv *priv = dev_get_priv(dev);
+
+	return ~readl(priv->base + TIMER0_VAL);
+}
+
+static int orion_timer_probe(struct udevice *dev)
+{
+	struct timer_dev_priv *uc_priv = dev_get_uclass_priv(dev);
+	struct orion_timer_priv *priv = dev_get_priv(dev);
+
+	priv->base = devfdt_remap_addr_index(dev, 0);
+	if (!priv->base) {
+		debug("unable to map registers\n");
+		return -ENOMEM;
+	}
+
+	uc_priv->clock_rate = CONFIG_SYS_TCLK;
+
+	writel(~0, priv->base + TIMER0_VAL);
+	writel(~0, priv->base + TIMER0_RELOAD);
+
+	/* enable timer */
+	setbits_le32(priv->base + TIMER_CTRL, TIMER0_EN | TIMER0_RELOAD_EN);
+
+	return 0;
+}
+
+static const struct timer_ops orion_timer_ops = {
+	.get_count = orion_timer_get_count,
+};
+
+static const struct udevice_id orion_timer_ids[] = {
+	{ .compatible = "marvell,orion-timer" },
+	{}
+};
+
+U_BOOT_DRIVER(orion_timer) = {
+	.name	= "orion_timer",
+	.id	= UCLASS_TIMER,
+	.of_match = orion_timer_ids,
+	.probe = orion_timer_probe,
+	.ops	= &orion_timer_ops,
+	.priv_auto	= sizeof(struct orion_timer_priv),
+};

include/configs/lsxl.h

@@ -22,73 +22,41 @@
 /*
  * Default environment variables
  */
-
-#if defined(CONFIG_LSXHL)
-#define CONFIG_FDTFILE "kirkwood-lsxhl.dtb"
-#elif defined(CONFIG_LSCHLV2)
-#define CONFIG_FDTFILE "kirkwood-lschlv2.dtb"
-#else
-#error "Unsupported board"
-#endif
-
 #define CONFIG_EXTRA_ENV_SETTINGS					\
 	"bootsource=legacy\0"						\
 	"hdpart=0:1\0"							\
-	"kernel_addr=0x00800000\0"					\
+	"kernel_addr_r=0x00800000\0"					\
-	"ramdisk_addr=0x01000000\0"					\
+	"ramdisk_addr_r=0x01000000\0"					\
-	"fdt_addr=0x00ff0000\0"						\
+	"fdt_addr_r=0x00ff0000\0"					\
+	"fdtfile=" CONFIG_DEFAULT_FDT_FILE "\0"				\
 	"bootcmd_legacy=sata init "					\
-		"&& load sata ${hdpart} ${kernel_addr} /uImage.buffalo "\
+		"&& load sata ${hdpart} ${kernel_addr_r} /uImage.buffalo "\
-		"&& load sata ${hdpart} ${ramdisk_addr} /initrd.buffalo "\
+		"&& load sata ${hdpart} ${ramdisk_addr_r} /initrd.buffalo "\
-		"&& bootm ${kernel_addr} ${ramdisk_addr}\0"		\
+		"&& bootm ${kernel_addr_r} ${ramdisk_addr_r}\0"		\
-	"bootcmd_net=bootp ${kernel_addr} vmlinuz "			\
+	"bootcmd_net=bootp ${kernel_addr_r} vmlinuz "			\
-		"&& tftpboot ${ramdisk_addr} initrd.img "		\
+		"&& tftpboot ${fdt_addr_r} ${fdtfile} "			\
-		"&& setenv ramdisk_len ${filesize} "			\
+		"&& tftpboot ${ramdisk_addr_r} initrd.img "		\
-		"&& tftpboot ${fdt_addr} " CONFIG_FDTFILE " "		\
+		"&& bootz ${kernel_addr_r} "				\
-		"&& bootz ${kernel_addr} "				\
+			"${ramdisk_addr_r}:${filesize} ${fdt_addr_r}\0"	\
-			"${ramdisk_addr}:${ramdisk_len} ${fdt_addr}\0"	\
 	"bootcmd_hdd=sata init "					\
-		"&& load sata ${hdpart} ${kernel_addr} /vmlinuz "	\
+		"&& load sata ${hdpart} ${kernel_addr_r} /vmlinuz "	\
-		"&& load sata ${hdpart} ${ramdisk_addr} /initrd.img "	\
+		"&& load sata ${hdpart} ${fdt_addr_r} /dtb "		\
-		"&& setenv ramdisk_len ${filesize} "			\
+		"&& load sata ${hdpart} ${ramdisk_addr_r} /initrd.img "	\
-		"&& load sata ${hdpart} ${fdt_addr} /dtb "		\
+		"&& bootz ${kernel_addr_r} "				\
-		"&& bootz ${kernel_addr} "				\
+			"${ramdisk_addr_r}:${filesize} ${fdt_addr_r}\0"	\
-			"${ramdisk_addr}:${ramdisk_len} ${fdt_addr}\0"	\
 	"bootcmd_usb=usb start "					\
-		"&& load usb 0:1 ${kernel_addr} /vmlinuz "		\
+		"&& load usb 0:1 ${kernel_addr_r} /vmlinuz "		\
-		"&& load usb 0:1 ${ramdisk_addr} /initrd.img "		\
+		"&& load usb 0:1 ${fdt_addr_r} ${fdtfile} "		\
-		"&& setenv ramdisk_len ${filesize} "			\
+		"&& load usb 0:1 ${ramdisk_addr_r} /initrd.img "	\
-		"&& load usb 0:1 ${fdt_addr} " CONFIG_FDTFILE " "	\
+		"&& bootz ${kernel_addr_r} "				\
-		"&& bootz ${kernel_addr} "				\
+			"${ramdisk_addr_r}:${filesize} ${fdt_addr_r}\0"	\
-			"${ramdisk_addr}:${ramdisk_len} ${fdt_addr}\0"	\
 	"bootcmd_rescue=run config_nc_dhcp; run nc\0"			\
-	"eraseenv=sf probe 0 "						\
-		"&& sf erase " __stringify(CONFIG_ENV_OFFSET)		\
-			" +" __stringify(CONFIG_ENV_SIZE) "\0"		\
 	"config_nc_dhcp=setenv autoload_old ${autoload}; "		\
 		"setenv autoload no "					\
 		"&& bootp "						\
 		"&& setenv ncip "					\
 		"&& setenv autoload ${autoload_old}; "			\
 		"setenv autoload_old\0"					\
-	"standard_env=setenv ipaddr; setenv netmask; setenv serverip; "	\
-		"setenv ncip; setenv gatewayip; setenv ethact; "	\
-		"setenv bootfile; setenv dnsip; "			\
-		"setenv bootsource legacy; run ser\0"			\
-	"restore_env=run standard_env; saveenv; reset\0"		\
-	"ser=setenv stdin serial; setenv stdout serial; "		\
-		"setenv stderr serial\0"				\
 	"nc=setenv stdin nc; setenv stdout nc; setenv stderr nc\0"	\
-	"stdin=serial\0"						\
-	"stdout=serial\0"						\
-	"stderr=serial\0"
-
-/*
- * Ethernet Driver configuration
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_MVGBE_PORTS		{0, 1} /* enable port 1 only */
-#define CONFIG_PHY_BASE_ADR		7
-#endif /* CONFIG_CMD_NET */
 
 #endif /* _CONFIG_LSXL_H */

include/configs/nsa310s.h

@@ -9,15 +9,42 @@
 #ifndef _CONFIG_NSA310S_H
 #define _CONFIG_NSA310S_H
 
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
 #include "mv-common.h"
 
-/* default environment variables */
+/* Include the common distro boot environment */
+#ifndef CONFIG_SPL_BUILD
+
+#define BOOT_TARGET_DEVICES(func) \
+	func(USB, usb, 0) \
+	func(SATA, sata, 0) \
+	func(DHCP, dhcp, na)
+
+#define KERNEL_ADDR_R	__stringify(0x800000)
+#define FDT_ADDR_R	__stringify(0x2c00000)
+#define RAMDISK_ADDR_R	__stringify(0x01100000)
+#define SCRIPT_ADDR_R	__stringify(0x200000)
+
+#define LOAD_ADDRESS_ENV_SETTINGS \
+	"kernel_addr_r=" KERNEL_ADDR_R "\0" \
+	"fdt_addr_r=" FDT_ADDR_R "\0" \
+	"ramdisk_addr_r=" RAMDISK_ADDR_R "\0" \
+	"scriptaddr=" SCRIPT_ADDR_R "\0"
+
+#include <config_distro_bootcmd.h>
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"console=console=ttyS0,115200\0" \
 	"kernel=/boot/zImage\0" \
 	"fdt=/boot/nsa310s.dtb\0" \
-	"bootargs_root=ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs rw\0"
+	"bootargs_root=ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs rw\0" \
+	LOAD_ADDRESS_ENV_SETTINGS \
+	BOOTENV
+
+#endif /* CONFIG_SPL_BUILD */
 
 /* Ethernet driver configuration */
 #define CONFIG_MVGBE_PORTS	{1, 0}	/* enable port 0 only */

include/configs/pogo_v4.h

@@ -21,15 +21,53 @@
  */
 #include "mv-common.h"
 
-/*
+/* Include the common distro boot environment */
- * Default environment variables
+#ifndef CONFIG_SPL_BUILD
- */
+
+#ifdef CONFIG_MMC
+#define BOOT_TARGET_DEVICES_MMC(func) func(MMC, mmc, 0)
+#else
+#define BOOT_TARGET_DEVICES_MMC(func)
+#endif
+
+#ifdef CONFIG_SATA
+#define BOOT_TARGET_DEVICES_SATA(func) func(SATA, sata, 0)
+#else
+#define BOOT_TARGET_DEVICES_SATA(func)
+#endif
+
+#ifdef CONFIG_USB_STORAGE
+#define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0)
+#else
+#define BOOT_TARGET_DEVICES_USB(func)
+#endif
+
+#define BOOT_TARGET_DEVICES(func) \
+	BOOT_TARGET_DEVICES_MMC(func) \
+	BOOT_TARGET_DEVICES_USB(func) \
+	BOOT_TARGET_DEVICES_SATA(func) \
+	func(DHCP, dhcp, na)
+
+#define KERNEL_ADDR_R	__stringify(0x800000)
+#define FDT_ADDR_R	__stringify(0x2c00000)
+#define RAMDISK_ADDR_R	__stringify(0x01100000)
+#define SCRIPT_ADDR_R	__stringify(0x200000)
+
+#define LOAD_ADDRESS_ENV_SETTINGS \
+	"kernel_addr_r=" KERNEL_ADDR_R "\0" \
+	"fdt_addr_r=" FDT_ADDR_R "\0" \
+	"ramdisk_addr_r=" RAMDISK_ADDR_R "\0" \
+	"scriptaddr=" SCRIPT_ADDR_R "\0"
+
+#include <config_distro_bootcmd.h>
+
 #define CONFIG_EXTRA_ENV_SETTINGS \
-	"dtb_file=/boot/dts/" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
+	LOAD_ADDRESS_ENV_SETTINGS \
-	"bootargs_console=console=ttyS0,115200\0" \
+	"fdtfile=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
-	"bootcmd_usb=usb start; load usb 0:1 0x00800000 /boot/uImage; " \
+	"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
-	"load usb 0:1 0x01100000 /boot/uInitrd; " \
+	"console=ttyS0,115200\0" \
-	"load usb 0:1 0x2c00000 $dtb_file\0"
+	BOOTENV
+#endif /* CONFIG_SPL_BUILD */
 
 /*
  * Ethernet Driver configuration

include/linux/mbus.h

@@ -33,16 +33,6 @@ struct mbus_dram_target_info {
 	} cs[4];
 };
 
-struct mvebu_mbus_state {
-	void __iomem *mbuswins_base;
-	void __iomem *sdramwins_base;
-	struct dentry *debugfs_root;
-	struct dentry *debugfs_sdram;
-	struct dentry *debugfs_devs;
-	const struct mvebu_mbus_soc_data *soc;
-	int hw_io_coherency;
-};
-
 /* Flags for PCI/PCIe address decoding regions */
 #define MVEBU_MBUS_PCI_IO  0x1
 #define MVEBU_MBUS_PCI_MEM 0x2
@@ -67,7 +57,6 @@ int mvebu_mbus_add_window_remap_by_id(unsigned int target,
 int mvebu_mbus_add_window_by_id(unsigned int target, unsigned int attribute,
 				phys_addr_t base, size_t size);
 int mvebu_mbus_del_window(phys_addr_t base, size_t size);
-int mbus_dt_setup_win(struct mvebu_mbus_state *mbus,
+int mbus_dt_setup_win(u32 base, u32 size, u8 target, u8 attr);
-		      u32 base, u32 size, u8 target, u8 attr);
 
 #endif /* __LINUX_MBUS_H */

lib/time.c

@@ -47,12 +47,15 @@ ulong timer_get_boot_us(void)
 {
 	ulong count = timer_read_counter();
 
-#if CONFIG_SYS_TIMER_RATE == 1000000
+#ifdef CONFIG_SYS_TIMER_RATE
-	return count;
+	const ulong timer_rate = CONFIG_SYS_TIMER_RATE;
-#elif CONFIG_SYS_TIMER_RATE > 1000000
+
-	return lldiv(count, CONFIG_SYS_TIMER_RATE / 1000000);
+	if (timer_rate == 1000000)
-#elif defined(CONFIG_SYS_TIMER_RATE)
+		return count;
-	return (unsigned long long)count * 1000000 / CONFIG_SYS_TIMER_RATE;
+	else if (timer_rate > 1000000)
+		return lldiv(count, timer_rate / 1000000);
+	else
+		return (unsigned long long)count * 1000000 / timer_rate;
 #else
 	/* Assume the counter is in microseconds */
 	return count;