The U-Boot is currently not capable of handling ethernet-phy-ieee802.3-c45
PHYs correctly, and also does not handle MDIO bus wide reset-gpios property.
Until proper C45 PHY support lands in U-Boot, disable AVB1/AVB2 interfaces.
This only disables the two MACs with 88Q2110/88Q2112 100/1000BASE-T1 PHYs
on ethenet sub-board, the main board AVB0 ethernet is unaffected.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
In rzg2l_pinconf_set(), there are no new variables defined in the case
statement for PIN_CONFIG_INPUT_ENABLE so no additional scope is needed.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
On the RZ/G2L SoC family, the direction of the Ethernet TXC/TX_CLK
signal is selectable to support an Ethernet PHY operating in either MII
or RGMII mode. By default, the signal is configured as an input and MII
mode is supported. The ETH_MODE register can be modified to configure
this signal as an output to support RGMII mode.
As this signal is be default an input, and can optionally be switched to
an output, it maps neatly onto an `output-enable` property in the device
tree.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The Ethenet interfaces on the Renesas RZ/G2L SoC family can operate at
multiple power supply voltages: 3.3V (default value), 2.5V and 1.8V.
rzg2l_pinconf_set() is extended to support the 2.5V setting, with a
check to ensure this is only used on Ethernet interfaces as it is not
supported on the SD & QSPI interfaces.
While we're modifying rzg2l_pinconf_set(), drop the unnecessary default
value for pwr_reg as it is set in every branch of the following if
condition.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
In the RZ/G2L family, core clocks are always on and can't be disabled.
However, drivers which are shared with other SoCs may call clk_enable()
or clk_enable_bulk() for a clock referenced in the device tree which
happens to be a core clock on the RZ/G2L. To avoid the need for
conditionals in these drivers, simply ignore attempts to enable a core
clock.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The env variable "SN" is used to store the serial number on DH electronics
SoMs. New SoMs will use the variable "dh_som_serial_number". To ensure
compatibility, these env variables are synchronized. This is achieved
using callback functions.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
In case there are two variables which each implement env callback
that performs env_set() on the other variable, the callbacks will
call each other recursively until the stack runs out. Prevent such
a recursion from happening.
Example which triggers this behavior:
static int on_foo(...) { env_set("bar", 0); ... }
static int on_bar(...) { env_set("foo", 0); ... }
U_BOOT_ENV_CALLBACK(foo, on_foo);
U_BOOT_ENV_CALLBACK(bar, on_bar);
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Suggested-by: Marek Vasut <marex@denx.de>
The new i.MX8M Plus DHCOM rev.200 is populated with M24C32-D EEPROM
that contains an additional write-lockable page called ID page, which
is populated with a structure containing ethernet MAC addresses, DH
item number and DH serial number.
Because the write-lockable page is not present on rev.100 i.MX8MP DHCOM
SoM, test whether EEPROM ID page exists by setting up the i2c driver.
There may be multiple EEPROMs with an ID page on this platform, always
use the first one. The evaluation of the EEPROM ID page is done in two
steps. First, the content is read and checked. This is done to cache
the content of the EEPROM ID page. Second, the content is extracted
from the EEPROM buffer by requesting it.
For the ethernet MAC address the i.MX8M Plus DHCOM currently supports
parsing address from multiple sources in the following priority order:
1) U-Boot environment 'ethaddr'/'eth1addr' environment variable
2) SoC OTP fuses
3) On-SoM EEPROM
Add support for parsing the content of this new EEPROM ID page and place
it between 2) and 3) on the priority list. The new entry is 2.5) On-SoM
EEPROM write-lockable page.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The new i.MX8M Plus DHCOM rev.200 is populated with M24C32-D EEPROM
that contains an additional write-lockable page called ID page. Add
aliases eeprom0wl and eeprom1wl for the access to the EEPROM ID
page node.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
iMX91 reuses iMX93 controller and PHY, but with lower speed,
so add new DDR rates for i.MX91.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX91 is a derived from i.MX93, and most clocks could be reused from
i.MX93. Also Update imx93-clock.h to sync with linux next.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
iMX91 is reduced part from iMX93 with part number: i.MX9131/11/01
It removed A55_1, M33, MIPI DSI, LVDS, etc.
i.MX9131:
- Support 2.4GT/s DDR and HWFFC at 1.2GT/s
i.MX9121:
- A55 at 800Mhz and DDR at 1600MTS, with low drive mode.
i.MX9111:
- Support 1.6GT/s DDR and HWFFC at 800MT/s
i.MX9101:
- Support 800Mhz ARM clock
- Support 1.6GT/s DDR and HWFFC at 800MT/s
- No parallel display, eQOS, flexcan
Updated Clock/Container/CPU and etc for i.MX91
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
According to iMX93 fuse burn plan, all 9x9 parts will have USB2,
ENET1 (FEC), LVDS1, CSI1 and DSI1 disabled. The codes missed ENET1
fuse when detecting 9x9. Although it still can detect 9x9 correctly,
we add the ENET1 fuse to the check to be more accurate.
Fixes: 58da865e27 ("imx9: add i.MX93 variants support")
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Replace '#if DEBUG' with '#ifdef DEBUG', otherwise '#define DEBUG 1'
should be used and conflict with '#define DEBUG' in include/log.h
Fixes: 5fda95fb94 ("imx: imx9: Add TRDC driver for TRDC init")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
have_dual_base is set to false, so the 8ulp_data will be put in BSS
section which conflicts with the area of u-boot.dtb which padded just
after u-boot-nodtb.bin. So move 8ulp_data to data section to avoid
its content being corrupted by dtb.
Fixes: 51cfa66f2c ("gpio: imx_rgpio2p: support one address")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move the environment into the board directory and convert header to a
txt file. In addition, this patch also applies following changes:
- Change default nfsroot path to /srv/nfs due to compliance with Linux
FHS 3.0.
- Rename specific variables as stated in the bootstd documentation.
Renamed variables:
fdt_addr => fdt_addr_r
fdt_file => fdtfile
Signed-off-by: Yunus Bas <y.bas@phytec.de>
When MbedTLS TLS features were added MBEDTLS_HAVE_TIME was defined as part
of enabling https:// support. However that pointed to the wrong function
which could crash if it received a NULL pointer.
Looking closer that function is not really needed, as it only seems to
increase the RNG entropy by using 4b of the current time and date.
The reason that was enabled is that lwIP was unconditionally requiring it,
although it's configurable and can be turned off.
Since lwIP doesn't use that field anywhere else, make it conditional and
disable it from our config.
Fixes: commit a564f5094f ("mbedtls: Enable TLS 1.2 support")
Reported-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Jerome Forissier <jerome.forissier@linaro.org>
Add a missing comma in the update_info structure declaration.
This fixes the following build error when building with
EFI_RUNTIME_UPDATE_CAPSULE or EFI_CAPSULE_ON_DISK:
board/emulation/qemu-arm/qemu-arm.c:52:9: error: request for member ‘images’ in something not a structure or union
Fixes: cccea18813 ("efi_loader: add the number of image entries in efi_capsule_update_info")
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Masahisa Kojima <masahisa.kojima@linaro.org>
Cc: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Cc: Tom Rini <trini@konsulko.com>
Building qemu_arm64_defconfig with CONFIGS_DM_RTC=n and CONFIGS_RTC_PL031=y
leads to a build failure.
Adjust the vexpress64 configuration to avoid circular dependency.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
There are platforms which set the value of ram_top based on certain
restrictions that the platform might have in accessing memory above
ram_top, even when the memory region is in the same DRAM bank. So,
even though the LMB allocator works as expected, when trying to
allocate memory above ram_top, prohibit this by marking all memory
above ram_top as reserved, even if the said memory region is from the
same bank.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Tested-by: Andreas Schwab <schwab@suse.de>
Bryan Brattlof <bb@ti.com> says:
Hello Everyone!
This small series converts TI's AM65x reference board to use
CONFIG_OF_UPSTREAM and removes the unused device tree files from
arch/arm/dts.
Because it's the last board using a AM65x without enabling OF_UPSTREAM
it allows us to also remove all the SoC FDT files as well and keep a
single version of the SoC's DT files in the dts/upstream directory going
forward.
Link: https://lore.kernel.org/r/20241121-am65x-v1-0-fe87aff1b5fc@ti.com
Rather than rely on manual updates from the arch/arm/dts directory,
enable CONFIG_OF_UPSTREAM to receive automatic device tree updates for
the am65x reference board.
Signed-off-by: Bryan Brattlof <bb@ti.com>
Based on the recommendation from HW team make modifications to
the sequence for more robustness.
- Unlock the PLL registers
- Enable external bypass
- Disable the PLL
- Program pllm and pllf
- Program Ref divider
- Enable other PLL controls like DSM_EN, DAC_EN,etc
- Enable calibration if available
- Enable PLL
- Wait for PLL lock and Calibration lock
- Remove external bypass
Re-write the full sequence from scratch as the previous sequence was way
off and keep it in a single commit for bisectability.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
base is more appropriate for the usage as the variable stores the base
address and seems more accurate w.r.t reg. Change reg to base.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Updated PLL driver sequencing requires us to use udelay in the PLL
driver as there is no poll bit to get the status of operations.
tick-timer(mcu_timer0/main_timer0) setting up the clocks for itself is
something that won't work as the PLL driver will be using udelay and
PLLs are configured during clock probe which would end up in a recursive
probe.
tick-timer being used by K3 devices are configured by ROM and we really
don't need to configure any of the clocks.
Remove the clock dependency from R5 stage as we don't need to setup
clocks for it.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Switch the callback static list from the board configuration variable
CFG_ENV_CALLBACK_LIST_STATIC to Kconfig CONFIG_ENV_CALLBACK_LIST_STATIC.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Those debug() calls might be useful, but beware. They can cause the DDR
controller to hang if we do not run the sequence quickly enough.
They usually are not an issue with upstream U-Boot and the default DDR
config, but they have become troublesome with custom DDR configs.
Drop those debug() statements that shouldn't be present in
time-sensitive code, to avoid anyone else falling into the trap.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Christian Marangi <ansuelsmth@gmail.com> says:
This series is split in 2 part.
While adapting the LED boot and activity code to the new property
accepted by Rob in dt-schema repository, a big BUG was discovered.
The reason wasn't clear at start and took me some days to figure it
out.
This was triggered by adding a new phandle in the test.dts to
introduce test for the new OPs.
This single addition caused the sandbox CI test to fail in the
dm_test_ofnode_phandle_ot test.
This doesn't make sense as reverting the change made the CI test
to correctly finish. Also moving the uboot node down
after the first phandle (in test.dts the gpio one) also made
the CI test to correctly finish.
A little bit of searching and debugging made me realize the
parse phandle OPs didn't support other.dts at all and they
were still referencing phandle index from test.dts.
(more info in the related commit)
In short the test was broken all along and was working by
pure luck. The first 4 patch address and fix the problem for good.
The other 4 patch expand and address the property change for
LED boot/activity.
Posting in a single series as changes are trivial and just
to speedup review process. (and also because the second
part depends on the first)
All CI tested with azure pipeline.
Link: https://lore.kernel.org/r/20241110115054.2555-1-ansuelsmth@gmail.com
Update test for LED activity and boot to follow new implementation with
property set to the LED node phandle.
Also update a copy-paste error in the function name for the activity
tests and actually enable the test with the DM_TEST macro.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update LED boot/activity to reference by phandle instead of label and
add to period property the "-ms" suffix.
This is a followup request by dt-schema maintainers that required LED
node to be referenced by a phandle to the node instead of indirectly by
the LED label and for timevalue to have a suffix.
While at it generalize the LED node label parsing since the logic is
common for generic LED bind and LED activity/boot.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add test for ofnode options phandle helper and add new property in the
sandbox test dts.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Implement ofnode_options phandle helper to get an ofnode from a phandle
option in /options/u-boot.
This helper can be useful since new DT yaml usually require to link a
phandle of a node instead of referencing it by name or other indirect
way.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Expand dm_test_ofnode_phandle(_ot) with new ofnode/tree_parse_phandle() op.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Implement ofnode/tree_parse_phandle() helper as an equivalent of
of_parse_phandle to handle simple single value phandle.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix broken dm_test_ofnode_phandle_ot test. They never actually worked
and were passing test by pure luck by having the same phandle index of
test.dts that coincicentally had #gpio-cells in the same index node.
It was sufficient to add a phandle to test.dts to make the test fail.
To correctly test these feature, make use oif the new OPs oftree to
parse phandle.
For consistency with the dm_test_ofnode_phandle, rework the test and
other.dts to use the same property with the other- prefix to every
node.
Also fix dm_test_ofnode_get_by_phandle_ot by making it more robust and
renaming the phandle property to other-phandle.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
