The original mtk_qspi driver has been removed. We change MT7629 to use
newly added mtk-spimem driver.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
This commits enables booting from eMMC when using SPL on 96Boards
Ficus board by adding SDHCI to boot order. Since the SDHCI driver
already has the reloc flag, this works straightaway. While we are at it,
let's also include the common u-boot dtsi for rk3399.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This commits enables booting from eMMC when using SPL on 96Boards
Rock960 board by adding SDHCI to boot order. Since the SDHCI driver
already has the reloc flag, this works straightaway. While we are at it,
let's also include the common u-boot dtsi for rk3399.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add devicetree support for Khadas Edge-Captain.
Khadas Captain is the carrier board for Khadas Edge.
Specification
- Rockchip RK3399
- Dual-Channel 2GB/4GB LPDDR4
- SD card slot
- Onboard 16GB/32GB/128GB eMMC
- RTL8211FD 1Gbps
- AP6356S/AP6398S WiFI/BT
- HDMI Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- Full 4 Lane M.2 Socket
- 16MB SPI Flash
- IR
- Programmable MCU
Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2:
"arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards"
(sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e)
Signed-off-by: Nick Xie <nick@khadas.com>
Tested-by: Chris Webb <chris@arachsys.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add devicetree support for Khadas Edge-V.
Khadas Edge-V is a Khadas VIM form factor Rockchip RK3399 board.
Specification
- Rockchip RK3399
- Dual-Channel 2GB/4GB LPDDR4
- SD card slot
- Onboard 16GB/32GB/128GB eMMC
- RTL8211FD 1Gbps
- AP6356S/AP6398S WiFI/BT
- HDMI Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- Full 4 Lane M.2 Socket
- 16MB SPI Flash
- IR
- Programmable MCU
Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2:
"arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards"
(sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e)
Signed-off-by: Nick Xie <nick@khadas.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add devicetree support for Khadas Edge.
Khadas Edge is an expandable Rockchip RK3399 board with goldfinger.
Specification
- Rockchip RK3399
- Dual-Channel 2GB/4GB LPDDR4
- Onboard 16GB/32GB/128GB eMMC
- RTL8211FD 1Gbps
- AP6356S/AP6398S WiFI/BT
- HDMI Out, DP
- USB 3.0, 2.0
- USB Type C power and data
- 16MB SPI Flash
- Programmable MCU
Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2:
"arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards"
(sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e)
Signed-off-by: Nick Xie <nick@khadas.com>
Tested-by: Chris Webb <chris@arachsys.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
DMA for MMCs can be enabled, since the previous patch fixes
the following issue in SPL:
Trying to boot from MMC1
spl: mmc init failed with error: -110
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The BCM2835/2836 watchdog is not used in mainline U-Boot at all. This
patch removes the driver and its references (CONFIG_BCM2835_WDT)
completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Paolo Pisati <p.pisati@gmail.com>
- sync Amlogic G12A DT with linux 5.3-rc1
- add support for 4GiB DRAM memory
- add support for Amlogic G12B based Odroid-N2
- small duplicate logic fix for gxbb clock driver
In attempts to speed up SPL and reduce size, the MDIO pin muxing
was inadvertently affected. Since the ethernet driver will setup
the pin muxing when ethernet is loaded, this patch will also
pinmux the MDIO pins at the same time. Once an DM compatible
MDIO driver is available, this can be removed.
Fixes: 877ab2423b ("ARM: davinci: da850: Manual pinmux only
when PINCTRL not available")
Signed-off-by: Adam Ford <aford173@gmail.com>
The commit 355be915ed ("arm: dts: k3-am654: Update power-domains
property for each node") has updated the power-domain cells value
and updated power-domains property in various existing dts nodes but
missed updating the cpsw_nuss node. This results in the following
build warning, fix this.
arch/arm/dts/k3-am654-base-board.dtb: Warning (power_domains_property): /interconnect@100000/interconnect@28380000/cpsw_nuss@046000000:power-domains: property size (8) too small for cell size 2
arch/arm/dts/k3-am654-r5-base-board.dtb: Warning (power_domains_property): /interconnect@100000/interconnect@28380000/cpsw_nuss@046000000:power-domains: property size (8) too small for cell size 2
Fixes: 355be915ed ("arm: dts: k3-am654: Update power-domains property for each node")
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
"fastboot flashall" expects "fastboot getvar product" value to be one of
values provided in android-info.txt file (in AOSP), from "require
board=" list. Before this patch, "am57xx" is returned for all AM57xx
based boards, as it's set in $board env var from SYS_BOARD in
board/ti/am57xx/Kconfig file, which is used for default implementation
of "fastboot getvar product".
In order to fix that inconsistency, let's do next:
1. In U-Boot: override fastboot.product, reusing the value from
$board_name
2. In AOSP: provide values for all AM57xx boards we can use to
device/ti/beagle_x15/board-info.txt file
This way requirements check in "fastboot flashall" will work as
expected, verifying that user tries to flash images to the board which
those images were built for.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Acked-by: Andrew F. Davis <afd@ti.com>
When configured with 4GiB DRAM size, only 3.8GiB is available, the
I/O beeing mapped in the last 256MiB of the first 4GiB physical memory/
First fixup the mm_region to handle the first 3.8GiB as memory and the
last 256MiB as I/O.
Then limit the real memory reported by the firmware to the available
physical space, 3.8GiB aligned with the mm_region memory zone size.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
Import HardKernel Odroid-N2 DT from Linux 5.3-rc1, commit 5f9e832c1370
("Linus 5.3-rc1") based on an Amlogic G12B S922X SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
Sync the Amlogic Meson G12A DT and Bindings file with the Linux 5.3-rc1
from the commit 5f9e832c1370 ("Linus 5.3-rc1").
Also remove the meson-g12a-u-boot.dtsi and meson-g12a-u200-u-boot.dtsi,
now conflicting with the main DT content.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
Xilinx/FPGA changes for v2019.10
fpga:
- Xilinx virtex2 cleanup
- Altera cyclon2 cleanup
zynq:
- Minor Kconfig cleanup
- Add psu_init configuration for Z-turn board
zynqmp:
- Add support for pmufw config passing to PMU
- script for psu_init conversion
- zcu1275 renaming
xilinx:
- Add support for UltraZed-EV SoM
Avnet UltraZed-EV Starter Kit is composed by the UltraZed-EV SoM and the
only publicly-available compatible carrier card. The SoM is based on the EV
version of the Xilinx ZynqMP SoC+FPGA.
The psu_init_gpl.c file has been generated from the board definition files
at [0] using Vivado 2018.3 and then minimized by
tools/zynqmp_psu_init_minimize.sh. Manually removed serdes init code since
it is not mentioned in device tree and fixed a checkpatch error.
[0] 3686c9ff7d/ultrazed_7ev_cc/1.1
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Optionally allow U-Boot to load a configuration object into the Power
Management Unit (PMU) firmware on Xilinx ZynqMP.
The configuration object is required by the PMU FW to enable most SoC
peripherals. So far the only way to boot using U-Boot SPL was to hard-code
the configuration object in the PMU firmware. Allow a different boot
process, where the PMU FW is equal for any ZynqMP chip and its
configuration is passed at runtime by U-Boot SPL.
All the code for Inter-processor communication with the PMU is isolated in
a new file (pmu_ipc.c). The code is inspired by the same feature as
implemented in the Xilinx First Stage Bootloader (FSBL) and Arm Trusted
Firmware:
* fb647e6b4c/lib/sw_apps/zynqmp_fsbl/src/xfsbl_misc_drivers.c (L295)
* c48d02bade/plat/xilinx/zynqmp/pm_service/pm_api_sys.c (L357)
SPL logs on the console before loading the configuration object:
U-Boot SPL 2019.07-rc1-00511-gaec224515c87 (May 15 2019 - 08:43:41 +0200)
Loading PMUFW cfg obj (2008 bytes)
EL Level: EL3
...
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Name of this platform has changed and released to customers that's why
name has also changed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Series-to: uboot
When an image is signed/encrypted on K2 devices the image may get padded
to meet alignment requirements for the signature/encryption type. The
original size is appended as 4 bytes little-endian to the end of the
final image.
Normally the trailing extra bytes are ignored and so restoring the
exact original size is not important. In the case of initrd the
original size is important as the kernel uses it to look for
additional filesystem data and can do the wrong thing when the
size is not correct.
Read off the original size and report it back from the image post
processing stage.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Enable the driver-model on da850-evm. We need to add a dummy nand node
to the device tree, as the real nand node is a sub-node of the aemif
device.
On linux the aemif driver populates all its child nodes, but we can't do
it in u-boot currently.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Enable the driver-model on da850-lcdk. We need to add a dummy nand node
to the device tree, as the real nand node is a sub-node of the aemif
device.
On linux the aemif driver populates all its child nodes, but we can't do
it in u-boot currently.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The pumpkin board is made by Gossamer Engineering and is using
a MediaTek SoC. The board currently comes in two available version:
MT8516 SoC and MT8167 SoC.
The board provides the following IOs: eMMC, NAND, SD card, USB type-A,
Ethernet, Wi-Fi, Bluetooth, Audio (jack out, 2 PDM port, 1 analog in),
serial over USB, and an expansion header.
Additionally there is a HDMI port, DSI port, and camera port only
on the MT8167 version of the board.
The board can be powered by battery and/or via a USB Type-C port and
is using a PMIC MT6392.
The eMMC and NAND are sharing pins and cannot be used together.
This commit is adding the basic boot support for the Pumpkin MT8516
board on the eMMC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
commit 49116e6d23 ("doc: arch: Convert README.sandbox to reST")
Moves README.sandbox to doc/arch.
Replace all the existing instances to point to the right documentation
file.
Signed-off-by: Keerthy <j-keerthy@ti.com>
- Clean up and migrate to use common rockchip spl board file
- Clean up and migrate to use common rockchip board file
- Increase rk3288 CONFIG_SYS_BOOTM_LEN to 16MB
Use common board file for board_init() and board_late_init(),
for Rockchip SoCs have very similar process.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use common board file for board_init() and board_late_init(),
for Rockchip SoCs have very similar process.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use common board file for board_init() and board_late_init(),
for Rockchip SoCs have very similar process.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use common board file for board_init() and board_late_init(),
for Rockchip SoCs have very similar process.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Use common board file for board_init() and board_late_init(),
for Rockchip SoCs have very similar process.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The rk3288_detect_reset_reason() is per-SoC operation, move
it to rk3288.c, and extend the rk_board_late_init() with
rk3288_board_late_init() to make all the board works fine
as before.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The veyron_init() should go to its board file veyron.c,
and the board_early_init_f() could be the right place.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use common board file for board_init() and board_late_init(),
for Rockchip SoCs have very similar process.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use common board file for board_init() and board_late_init(),
for Rockchip SoCs have very similar process.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
