Use upstream device tree files and bindings. To do so:
- imply (enable) OF_UPSTREAM option for E850-96 target
- point DEFAULT_DEVICE_TREE in E850-96 config to upstream dts
- remove now not needed local dts files, binding docs and headers
- update MAINTAINERS and board/samsung/e850-96/MAINTAINERS
correspondingly
Upstream device tree files for Exynos850 SoC and E850-96 board are
pretty much the same as local (removed) ones, so the conversion is
rather straightforward and painless in this case. The appended dts file
(arch/arm/dts/exynos850-e850-96-u-boot.dtsi) stays unchanged.
The only remaining local dt-bindings doc for E850-96 board is
exynos-pmu.yaml. It wasn't removed as it's quite different from Linux
kernel version. Particularly U-Boot local version of exynos-pmu.yaml
describes "samsung,uart-debug-1" property, which is not present in Linux
kernel binding. Later it might be upstreamed to Linux kernel, and once
it's done the U-Boot exynos-pmu.yaml binding can be removed.
No functional change.
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The Indiedroid Nova is a Rockchip RK3588S based SBC from Indiedroid.
Specifications:
Rockchip RK3588S SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
4/8/16GB memory LPDDR4x
Mali G610MC4 GPU
Optional eMMC
2x USB 2.0, 2x USB 3.0, 1x USB 3.0 C port with DP Alt
1x MIPI-CSI Port (4-lane or 2x 2-lane)
1x MIPI-DSI 4-lane connector
1x Micro HDMI 2.1 output, 1x DP 1.4 output
Gigabit Ethernet
Realtek RTL8821CS WiFi
4 pin debug UART connector
40 pin GPIO header
Size: 85mm x 56mm (Raspberry Pi Form Factor)
Kernel commit:
3900160e164b ("arm64: dts: rockchip: Add Indiedroid Nova board")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Powkiddy X55 is a Rockchip RK3566 based handheld gaming device.
UART, ADC, eMMC, and SDMMC are tested to work in U-Boot and this
successfully boots mainline Linux.
Kernel commit:
e99adc97e21a ("arm64: dts: rockchip: Add Powkiddy X55")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Migrate RV1126 boards that exists in Linux v6.8 to use OF_UPSTREAM.
Following targets is migrated to use OF_UPSTREAM:
- rv1126-edgeble-neu2 : Board is an industrial form factor
IO board.
- sonoff-ihost-rv1126 : Gateway device designed to provide a
Smart Home Hub.
Cc: Tim Lunn <tim@feathertop.org>
Cc: Jagan Teki <jagan@edgeble.ai>
Reviewed-By: Tim Lunn <tim@feathertop.org>
Tested-By: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Anand Moon <anand@edgeble.ai>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
After the conversion of RV1108 to OF_UPSTREAM,
include/dt-bindings/clock/rv1108-cru.h is no longer needed because
there is dts/upstream/include/dt-bindings/clock/rv1108-cru.h from
upstream Linux.
Remove the unneeded rv1108-cru.h file.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d, reversing
changes made to 2ee6f3a5f7.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Specifying a file in an EXT4 or FAT partition on a virtio device as
environment location failed because virtio hadn't been initialized by
the time the environment was loaded. This patch mirrors commit
54ee5ae841 ("Add SCSI scan for ENV in EXT4 or FAT") in issue and
fix, just for a different kind of block device.
The additional include in include/virtio.h is needed so all functions
called there are defined, the alternative would have been to include
dm/device.h separately in the env/ sources.
Checkpatch suggests using "if (IS_ENABLED(CONFIG...))" instead of
"#if defined(CONFIG_...)", I'm sticking to the style of the existing
code here.
Signed-off-by: Fiona Klute <fiona.klute@gmx.de>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Bin Meng <bmeng.cn@gmail.com>
CC: Rogier Stam <rogier@unrailed.org>
Greg Malysa <greg.malysa@timesys.com> says:
This series adds support for the ADI SC5xx machine type and includes two
core drivers that are required for being able to boot any board--a UART
driver, the gptimer driver which is used as a clock reference (CNTVCNT
is not supported on the armv7 sc5xx SoCs) and the clock tree driver. Our
corresponding Linux support relies on u-boot configuring the clocks
correctly before booting, so it is not possible to boot any board
without the CGU/CDU configuration happening here. There are also no
board files, device trees, or defconfigs included here, but some common
definitions that will be used to build board files currently are. The
sc5xx SoCs themselves include many armv7 families (sc57x, sc58x, and
sc594) all using an ARM Cortex-A5, and one armv8 family (sc598) indended
to be a drop-in replacement for the SC594 in terms of peripherals, with
a Cortex-A55 instead.
Some of the configuration code in dmcinit and clkinit is quite scary and
causes a lot of checkpatch violations. It is modified from code
initially provided by ADI, but it has not been fully rewritten. There's
a question of how important it is to clean up this code--it has some
quality violations, but it has been in use (including in production) for
over two years and is known to work for performing the low level SoC
initialization, while a rewrite might introduce timing or sequence bugs
that could take a significant amount of time to detect in the future.
Add support for the SC5xx machine type from Analog Devices. This
includes support for the SC57x, SC58x, SC59x, and SC59x-64 SoCs, which
have many common features such as common ADI IP blocks, and SHARC DSP
cores. This commit introduces core functionality required for all boards
using an SC5xx SoC, such as:
- SPL configuration
- Required CPU hooks such as reset
- Boot ROM interaction to load the stage 2 bootloader in the reference
configuration. Other options are possible but not officially supported
at this time
- SoC-common configuration expected to be reused by all boards
- Early initialization for system clocks and DDR controller
Co-developed-by: Greg Malysa <greg.malysa@timesys.com>
Signed-off-by: Greg Malysa <greg.malysa@timesys.com>
Co-developed-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas@analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal@analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs@analog.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
In the case of PowerPC, this file needs to include <asm/ppc.h> in order
to resolve all of the references it makes.
Signed-off-by: Tom Rini <trini@konsulko.com>
The constraints on the MMC_SUPPORTS_TUNING symbol can easily be
expressed in Kconfig (with the addition of SPL_MMC_SUPPORTS_TUNING).
Furthermore, in order to remove <common.h> from the MMC subsystem, the
way this symbol is used today needs to be changed in order to continue
functioning.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove redundant device tree files now that RK3588 boards have been
migrated to use OF_UPSTREAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove redundant device tree files now that RK356x boards have been
migrated to use OF_UPSTREAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove redundant device tree files now that RK3399 boards have been
migrated to use OF_UPSTREAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove redundant device tree files now that RK3328 boards have been
migrated to use OF_UPSTREAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove redundant device tree files now that RK3308 boards have been
migrated to use OF_UPSTREAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-cru.h with one from Linux kernel v6.2+ and fix use of the
SCLK_DDRCLK name that was only used by U-Boot.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This follows the example of RISC-V where <asm/global_data.h> includes
<asm/u-boot.h> directly as "gd" includes a reference to bd_info already
and so the first must include the second anyhow. We then remove
<asm/u-boot.h> from all of the places which include references to "gd"
an so have <asm/global_data.h> already.
Signed-off-by: Tom Rini <trini@konsulko.com>
A few headers rely on indirect inclusion of <linux/types.h> or
<linux/kernel.h> so add them directly. In the case of <netdev.h> add a
"struct bd_info;" as well rather than the large header chain to resolve
that.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove <common.h> from all powerpc architecture files and when needed add
missing include files directly. This typically involves using
<asm/u-boot.h> instead due to the difficult nested structure of the
PowerPC includes themselves.
Signed-off-by: Tom Rini <trini@konsulko.com>
To ensure that board config headers which set values here in the CFG_SYS
range are used, this header needs to include <config.h> directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to avoid needing to add <command.h> to this file, add "struct
cmd_tbl" before the prototype for do_bdinfo().
Signed-off-by: Tom Rini <trini@konsulko.com>
When u-boot enable CONFIG_SYS_BOOT_RAMDISK_HIGH, rootfs image relocated
from FIU address space to memory address before jump to kernel.
Since Arbel reserved memory from 0x00000000 to 0x06200000 for tip image,
and rootfs image may too large that cannot found a suitable location
before 128MB(0x8000000), so increase mapping size from 128MB to 192MB.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Commit 37cb626da2 ("mmc: sdhci: Add Support for ADMA2") introduced
ADMA_DESC_LEN == 16 (64 bit case), but it was never used before commit
74755c1fed ("mmc: sdhci: introduce adma_write_desc() hook to struct sdhci_ops").
"sizeof(struct sdhci_adma_desc)" (== 12 for 64bit case) was used instead.
Confusion probably originates from Linux commit 685e444bbaa0
("mmc: sdhci: Add ADMA2 64-bit addressing support for V4 mode"), but
the latter "V4 mode" was never ported to U-Boot.
Fixes: 74755c1fed ("mmc: sdhci: introduce adma_write_desc() hook to struct sdhci_ops")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Tested-by: Jonathan Humphreys <j-humphreys@ti.com>
Tested-by: Judith Mendez <jm@ti.com>
Since we support QueryVariableInfo at runtime now add the relevant
tests. Since we want those to be reusable at bootime, add them
in a separate file
Add tests for
- Test QueryVariableInfo returns EFI_SUCCESS
- Test null pointers for the function arguments
- Test invalid combination of attributes
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Caleb Connolly <caleb.connolly@linaro.org> says:
This is a subset of [1]. With more platform maintainers switching to
OF_UPSTREAM I didn't want to get in the way (it has also proven more
difficult than I hoped to remove only the fully compatible header
files).
This series removes only the dt-bindings headers which contain generic
data like GPIO flags, input event codes, etc.
It then implements support for building all DTBs for a vendor with
OF_UPSTREAM_BUILD_VENDOR. This removes the need to maintain a set list
of DTBs that can be built by U-Boot and opens up the possibility of new
boards becoming supported "by default" just by landing their DT
upstream.
[1]: https://lore.kernel.org/u-boot/20240321-b4-upstream-dt-headers-v2-0-1eac0df875fe@linaro.org
