Coreboot tables provide information about the CMOS-RAM checksum. Add a
command which can check and update this.
With this it is possible to adjust CMOS-RAM settings and tidy up the
checksum afterwards.
Signed-off-by: Simon Glass <sjg@chromium.org>
U-Boot has a fairly rigid memory map which is normally not visible
unless debugging is enabled in board_f.c
Update the 'meminfo' command to show it. This command does not cover
arch-specific pieces but gives a good overview of where things are.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to obtain the results of MSR queries as well as to update
MSR registers, so add a command these tasks.
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds TCPM framework in preparation for fusb302 support, which can
handle USB power delivery messages. This is needed to solve issues with
devices, that are running from a USB-C port supporting USB-PD, but not
having a battery.
Such a device currently boots to the kernel without interacting with
the power-supply at all. If there are no USB-PD message replies within
5 seconds, the power-supply assumes the peripheral is not capable of
USB-PD. It usually takes more than 5 seconds for the system to reach
the kernel and probe the I2C based fusb302 chip driver. Thus the
system always runs into this state. The power-supply's solution to
fix this error state is a hard reset, which involves removing the
power from VBUS. Boards without a battery (or huge capacitors) will
reset at this point resulting in a boot loop.
This imports the TCPM framework from the kernel. The porting has
originally been done by Rockchip using hardware timers and the Linux
kernel's TCPM code from some years ago.
I had a look at upgrading to the latest TCPM kernel code, but that
beast became a lot more complex due to adding more USB-C features.
I believe these features are not needed in U-Boot and with multiple
kthreads and hrtimers being involved it is non-trivial to port them.
Instead I worked on stripping down features from the Rockchip port
to an even more basic level. Also the TCPM code has been reworked
to avoid complete use of any timers (Rockchip used SoC specific
hardware timers + IRQ to implement delayed work mechanism). Instead
the delayed state changes are handled directly from the poll loop.
Note, that (in contrast to the original Rockchip port) the state
machine has the same hard reset quirk, that the kernel has - i.e.
it avoids disabling the CC pin resistors for devices that are not
self-powered. Without that quirk, the Radxa Rock 5B will not just
end up doing a machine reset when a hard reset is triggered, but will
not even recover, because the CPU will loose power and the FUSB302
will keep this state because of leak voltage arriving through the RX
serial pin (assuming a serial adapter is connected).
This also includes a 'tcpm' command, which can be used to get
information about the current state and the negotiated voltage
and current.
Co-developed-by: Wang Jie <dave.wang@rock-chips.com>
Signed-off-by: Wang Jie <dave.wang@rock-chips.com>
Tested-by: Soeren Moch <smoch@web.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add a 'upl' command to work with Universal Payload features. For now it
only supports reading and writing a handoff structure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add documentation for the 'cpu' command, taking NXP i.MX 8M Plus
as a example.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This command can be used to print the current parser with 'cli get'.
It can also be used to set the current parser with 'cli set'.
For the moment, only one value is valid for set: old.
Signed-off-by: Francis Laniel <francis.laniel@amarulasolutions.com>
bootX measurements and measurement API moved to u-boot core:
Up to now, U-Boot could perform measurements and EventLog creation as
described by the TCG spec when booting via EFI.
The EFI code was residing in lib/efi_loader/efi_tcg2.c and contained
both EFI specific code + the API needed to access the TPM, extend PCRs
and create an EventLog. The non-EFI part proved modular enough and
moving it around to the TPM subsystem was straightforward.
With that in place we can have a common API for measuring binaries
regardless of the boot command, EFI or boot(m|i|z), and contructing an
EventLog.
I've tested all of the EFI cases -- booting with an empty EventLog and
booting with a previous stage loader providing one and found no
regressions. Eddie tested the bootX part.
Eddie also fixed the sandbox TPM which couldn't be used for the EFI code
and it now supports all the required capabilities. This had a slight
sideeffect in our testing since the EFI subsystem initializes the TPM
early and 'tpm2 init' failed during some python tests. That code only
opens the device though, so we can replace it with 'tpm2 autostart'
which doesn't error out and still allows you to perfom the rest of the
tests but doesn't report an error if the device is already opened.
There's a few minor issues with this PR as well but since testing and
verifying the changes takes a considerable amount of time, I prefer
merging it now.
Heinrich has already sent a PR for -master containing "efi_loader: fix
EFI_ENTRY point on get_active_pcr_banks" and I am not sure if that will
cause any conflicts, but in any case they should be trivial to resolve.
Both the EFI and non-EFI code have a Kconfig for measuring the loaded
Device Tree. The reason this is optional is that we can't reason
when/if devices add random info like kaslr-seed, mac addresses etc in
the DT. In that case measurements are random, board specific and
eventually useless. The reason it was difficult to fix it prior to this
patchset is because the EFI subsystem and thus measurements was brought
up late and DT fixups might have already been applied. With this
patchset we can measure the DT really early in the future.
Heinrich also pointed out that the two Kconfigs for the DTB measurements
can be squashed in a single one and that the documentation only explains
the non-EFI case. I agree on both but as I said this is a sane working
version, so let's pull this first it's aleady big enough and painful to
test.
There is a function for this but it is never used. Showing the history is
a useful feature, so add a new 'history' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is a stub describing how TPL, VPL, and SPL load the next boot stages
on a detail level for users.
For sure we will need a few patches on top to catch the whole complexity.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Provide armffa command showcasing the use of the U-Boot FF-A support
armffa is a command showcasing how to invoke FF-A operations.
This provides a guidance to the client developers on how to
call the FF-A bus interfaces. The command also allows to gather secure
partitions information and ping these partitions. The command is also
helpful in testing the communication with secure partitions.
For more details please refer to the command documentation [1].
A Sandbox test is provided for the armffa command.
[1]: doc/usage/cmd/armffa.rst
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
This reverts commit d927d1a808, reversing
changes made to c07ad9520c.
These changes do not pass CI currently.
Signed-off-by: Tom Rini <trini@konsulko.com>
Provide armffa command showcasing the use of the U-Boot FF-A support
armffa is a command showcasing how to invoke FF-A operations.
This provides a guidance to the client developers on how to
call the FF-A bus interfaces. The command also allows to gather secure
partitions information and ping these partitions. The command is also
helpful in testing the communication with secure partitions.
For more details please refer to the command documentation [1].
[1]: doc/usage/cmd/armffa.rst
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add a new 'cedit' command which allows editing configuration using an
expo. The configuration items appear as menus on the display.
This is extremely basic, only supporting menus and not providing any way
to load or save the configuration.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reformat and rewrite the documentation for this command.
This is a complicated command, so further improvements are welcome.
Signed-off-by: Simon Glass <sjg@chromium.org>
Create a new usage/fit directory which will house information about FIT.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Explain block maps by going through two common use-cases.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The read and write commands are, deliberately, implemented in the same
file, so that they stay feature-compatible (e.g. if someone implements
support for "read the full partition, however large that is", that
same syntax should also work for write). In order to ensure the
documentation for both are similarly kept in sync, and to avoid
duplication, document them both in read.rst, and add a stub write.rst
referring to read.rst.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Revamp the documentation for the new features, including a description of
the new features and documentation for the trace command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a command to load SEAMA (Seattle Image), a NAND flash
on-flash storage format.
This type of flash image is found in some D-Link routers such
as DIR-645, DIR-842, DIR-859, DIR-860L, DIR-885L, DIR890L and
DCH-M225, as well as in WD and NEC routers on the ath79
(MIPS), Broadcom BCM53xx, and RAMIPS platforms.
This U-Boot command will read and decode a SEAMA image from
raw NAND flash on any platform. As it is always using big endian
format for the data decoding is always necessary on platforms
such as ARM.
The command is needed to read a SEAMA-encoded boot image on the
D-Link DIR-890L router for boot from NAND flash in an upcoming
port of U-Boot to the Broadcom Northstar (BCM4709, BCM53xx)
architecture.
A basic test and documentation is added as well. The test must
be run on a target with NAND flash support and at least one
resident SEAMA image in flash.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- jethub j100: add rescue boot from microSD
- move meson sm command to cmd/meson and add efusedump sub-command
- switch dwc2 otg to DM for G12A, GXL & AXG
- Add new boards:
- Odroid Go Ultra
- Odroid-N2L
