The SCLK_MAC_PLL id is not exported or referenced upstream. It is also
not referenced in vendor U-Boot or vendor kernel 4.4, 4.19, 5.10 or 6.1.
Relax the check for parent id SCLK_MAC_PLL when using internal clock
source for gmac to allow use of clock/rk3288-cru.h from dts/upstream.
All in-tree and upstream rk3288 DTs use an external clock as parent,
so no functional change to boards is expected with this change.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
According to the mt7629 programming guide, the CLK_TOP_F10M_REF_SEL
shares the same parent selection with CLK_TOP_IRRX_SEL, while the
present parent selection for CLK_TOP_F10M_REF_SEL is actually used
for CLK_TOP_SGMII_REF_1_SEL.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Early revisions of the R-Car V4M Series Hardware User’s Manual
contained an incorrect formula for the CPU core clocks:
ZCnφ = (PLL2VCO x 1/2) x mult/32
Dang-san fixed this by using CLK_PLL2_DIV2 instead of CLK_PLL2 as the
parent clock.
In Rev.0.70 of the documentation, the formula was corrected to:
ZCnφ = (PLL2VCO x 1/4) x mult/32
As the CPG Block Diagram now shows a separate 1/4 post-divider for PLL2,
the use of CLK_PLL2_DIV2 is a recurring source of confusion. Hence get
rid of CLK_PLL2_DIV2, and include the proper 1/4 post-divider in the
invocation of the DEF_GEN4_Z() macro, like is done on other R-Car Gen4
(and Gen3) SoCs.
Ported from Linux commit
92850bed9d4d ("clk: renesas: r8a779h0: Drop CLK_PLL2_DIV2 to clarify ZCn clocks")
Reported-by: Vinh Nguyen <vinh.nguyen.xz@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/0d2789cac2bf306145fe0bbf269c2da5942bb68f.1728377724.git.geert+renesas@glider.be
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Enable OF_UPSTREAM to use upstream DT and add starfive/ prefix to
the DEFAULT_DEVICE_TREE. Rename jh7110-starfive-visionfive-2-u-boot.dtsi
to jh7110-starfive-visionfive-2-v1.3b-u-boot.dtsi and set the v1.3b
device tree as the default device tree.
Drop redundant DT files from arch/riscv/dts/ and redundant clock and
reset definitions from include/dt-bindings/.
Since the old clock definitions is a little different from those in
upstream Linux, update the clock definitions in clock drivers
accordingly.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
In case DM drivers probe earlier than board clock setup is done
init of basic clocks should be done in CAR driver probe as well.
Add it to avoid possible clock related problems.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Return PLL id into struct clk if PLL is parsed from device
tree instead of throwing an error. Allow requesting PLL
clock rate via get_rate op.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Sometimes clocks provided to a consumer might not have .set_rate
operation (like gate or mux clocks), but have CLK_SET_PARENT_RATE flag
set. In that case it's usually possible to find a parent up the tree
which is capable of setting the rate (div, pll, etc). Implement a simple
lookup procedure for such cases, to traverse the clock tree until
.set_rate capable parent is found, and use that parent to actually
change the rate. The search will stop once the first .set_rate capable
clock is found, which is usually enough to handle most cases.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
The correct spelling is R-Car, including the dash, update the usage.
Kconfig strings and comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
In the RZ/G2L family, core clocks are always on and can't be disabled.
However, drivers which are shared with other SoCs may call clk_enable()
or clk_enable_bulk() for a clock referenced in the device tree which
happens to be a core clock on the RZ/G2L. To avoid the need for
conditionals in these drivers, simply ignore attempts to enable a core
clock.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
i.MX91 is a derived from i.MX93, and most clocks could be reused from
i.MX93. Also Update imx93-clock.h to sync with linux next.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Based on the recommendation from HW team make modifications to
the sequence for more robustness.
- Unlock the PLL registers
- Enable external bypass
- Disable the PLL
- Program pllm and pllf
- Program Ref divider
- Enable other PLL controls like DSM_EN, DAC_EN,etc
- Enable calibration if available
- Enable PLL
- Wait for PLL lock and Calibration lock
- Remove external bypass
Re-write the full sequence from scratch as the previous sequence was way
off and keep it in a single commit for bisectability.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
base is more appropriate for the usage as the variable stores the base
address and seems more accurate w.r.t reg. Change reg to base.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
This breaks chromebook_coral which says:
Video: No video mode configured in FSP!
This reverts commit 2e9313179a.
Signed-off-by: Simon Glass <sjg@chromium.org>
In case lists_driver_lookup_name("rst_gen3") fails, the clk_gen3 driver
has to be unbound before erroring out. Reorder the function such that
both clk_gen3 and rst_gen3 drivers are looked up first, if either look
up fails then the function errors out right away. Second, the clk_gen3
is bound, if binding fails, the function still errors out right away
because there is nothing to undo after either lists_driver_lookup_name()
call. Finally, rst_gen3 is bound and if this binding fails, then that
is the only place where clk_gen3 has to be unbound before erroring out.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Why get a devicetree description wrong once when you can get it wrong
twice? The original mistake, which the driver supports was failing to
describe the main PLL that the "cfg" and "periph" clocks parented by.
The second mistake was describing the "cfg" and "periph" clocks a
reg region within the clock controller, rather as two registers within
a syscon region that also contains pinctrl, interrupt muxing controls
and other functions.
Make up for lost time and describe these regions as they should have
been originally, preserving support for the existing two configurations
for the sake of existing systems with firmware-provided devicetrees.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Two of the clocks required by the usdhc1 controller are missing from the
clock controller node. A recent change enables all the clocks in the
esdhc node, which fails as they are not defined in the clock controller.
Fixes: 76332fae76 ("mmc: fsl_esdhc_imx: Enable AHB/IPG clk with clk bulk API")
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Add dedicated getter and setter for SCLK_UART0_PMU.
This allows the driver to correctly handle UART0 clocks, and thus
it fixes the issues with UART0 not working in case DEBUG_UART is
disabled.
Unlike other Rockchip SoCs, i.e. rk3399, in the PX30 the default
clock source for UART is GPLL, instead of external oscillator.
If the DEBUG_UART is enabled, the clock source is changed in
board_debug_uart_init function to 24Mhz oscillator, which also
matches the fallback value obtained from DT node.
In case the DEBUG_UART is disabled, the UART clock source remains
default, and the DM serial driver wrongly configures the baud rate,
resulting in broken communication.
By implementing the UART clock getter/setter, the serial driver
can probe the actual configuration and corectly configure itself.
The DEBUG_UART settings now should not affect it.
The driver supports GPLL and 24M oscillator. NPLL and USBPHY480M
sources, that are managed by CRU, are not yet handled, as likely
they won't be used in real scenarios.
Signed-off-by: Lukasz Czechowski <lukasz.czechowski@thaumatec.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There is a dummy clk entry for i.MX8QM/QXP, so add the dummy clk enable
and get rate. Otherwise "__imx8_clk_enable(Invalid clk ID #0)".
Fixes: 76332fae76 ("mmc: fsl_esdhc_imx: Enable AHB/IPG clk with clk bulk API")
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Heiko Schocher <hs@denx.de>
- Add Libre Computer boards into proper libre-computer board directory
- Add new Boards:
- Libre Computer aml-s905d3-cc
- Libre Computer aml-a311d-cc
- Add capsule update to libretech-ac and the new boards since they have an onboard SPI nor flash
- Fix HDMI support after sync to v6.11 and regulator enable from Marek
- Fix khadas-vim3 android config for android-mainline kernel
- Disable meson64 boot targets when configs are not eavailable
This switches all boards with the Allwinner H616/H618/H313/H700 SoCs over to
use OF_UPSTREAM. We are doing it for this SoC family only since the DTs
between the U-Boot and the kernel repo are exactly identical, whereas other
families have one compatibility fix in U-Boot to allow booting older kernels.
Other will follow if this plays out well.
The biggest chunk otherwise is adding support for an Anbernic game console,
using the H700 SoC. For that we need to enhance the DRAM support code, and
pick two DT commits from the mainline kernel/DT rebasing repo, followed
by the defconfig patch.
On top of that two small fixes for the old Allwinner A80.
Gitlab CI passed, and I booted that briefly on some boards, including an
H616 and an H618 one (with LPDDR4).
Simon Glass <sjg@chromium.org> says:
When the SPL build-phase was first created it was designed to solve a
particular problem (the need to init SDRAM so that U-Boot proper could
be loaded). It has since expanded to become an important part of U-Boot,
with three phases now present: TPL, VPL and SPL
Due to this history, the term 'SPL' is used to mean both a particular
phase (the one before U-Boot proper) and all the non-proper phases.
This has become confusing.
For a similar reason CONFIG_SPL_BUILD is set to 'y' for all 'SPL'
phases, not just SPL. So code which can only be compiled for actual SPL,
for example, must use something like this:
#if defined(CONFIG_SPL_BUILD) && !defined(CONFIG_TPL_BUILD)
In Makefiles we have similar issues. SPL_ has been used as a variable
which expands to either SPL_ or nothing, to chose between options like
CONFIG_BLK and CONFIG_SPL_BLK. When TPL appeared, a new SPL_TPL variable
was created which expanded to 'SPL_', 'TPL_' or nothing. Later it was
updated to support 'VPL_' as well.
This series starts a change in terminology and usage to resolve the
above issues:
- The word 'xPL' is used instead of 'SPL' to mean a non-proper build
- A new CONFIG_XPL_BUILD define indicates that the current build is an
'xPL' build
- The existing CONFIG_SPL_BUILD is changed to mean SPL; it is not now
defined for TPL and VPL phases
- The existing SPL_ Makefile variable is renamed to SPL_
- The existing SPL_TPL Makefile variable is renamed to PHASE_
It should be noted that xpl_phase() can generally be used instead of
the above CONFIGs without a code-space or run-time penalty.
This series does not attempt to convert all of U-Boot to use this new
terminology but it makes a start. In particular, renaming spl.h and
common/spl seems like a bridge too far at this point.
The series is fully bisectable. It has also been checked to ensure there
are no code-size changes on any commit.
Use PHASE_ as the symbol to select a particular XPL build. This means
that SPL_TPL_ is no-longer set.
Update the comment in bootstage to refer to this symbol, instead of
SPL_
Signed-off-by: Simon Glass <sjg@chromium.org>
Clock gates and reset lines share a common structure in the sunxi clock
driver descriptions, but use different flags to tell them apart.
The description of the Allwinner A80 MMC clock reset lines was
erroneously using the "GATE" macro, which made the reset driver ignore
that entry, complaining with:
sunxi_set_reset: (RST-reset:#0) unhandled
Change that to the correct "RESET" macro, to make the reset driver
happy.
Fixes e0c7ce7e52 ("sunxi: clk: A80: add MMC clock support")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The SSCG is active with MDSEL[12] is not set. Previous commit
99c7e03119 ("clk: renesas: rcar-gen3: Replace SSCG caching
with MDSEL/PE caching") inverted the conditional assignment
of priv->sscg = !(cpg_mode & BIT(12)) during conversion from
(priv->sscg ? 16 : 0) to priv->cpg_mode & BIT(core->offset) ? 16 : 0;
Invert the assignment back to the correct state.
This fixes R8A77980, R8A77990, R8A77995 and R8A774C0.
Fixes: 99c7e03119 ("clk: renesas: rcar-gen3: Replace SSCG caching with MDSEL/PE caching")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add support for dumping a few of the clocks used on Qualcomm platforms.
Naming the Global PLL's, Root Clock Generators, and gate clocks.
This helps a lot with platform bringup and feature enablement by making
it easy to sanity check that the clocks are programmed correctly.
== Usage ==
Enable CONFIG_CMD_CLK and "#define LOG_DEBUG" at the top of
qcom-<soc>.c.
The "clk dump" command should print the states of all the gates, GPLLs
and RCGs for your SoC.
== Glossary ==
RCG: Root Clock Generator
* Takes in some fairly arbitrary high freq clock (configurable clock
source and options for taking just even pulses and other things)
* Output frequency = input_freq * (m/n) * (1/d) where m/n are arbitrary
8 or 16-bit values (depending on the RCG), and d is a number (with
support for .5 offsets).
GPLL: Global Phase Locked Loop
* Crystal as input
* integer multiplier + exponent part (2^-40)
Gate: Simple on/off clock
* Put between RCGs and the peripherals they power
* Required to allow for correct power sequencing
If you do the maths manually using the equations from "clk dump", the
numbers should roughly line up by they're likely to be out by a handful
of MHz. They output is formatted so that it can be pasted directly into
the python interpreter.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Add clock, reset and power domain driver for SM8150. Driver code is
based on the similar U-Boot drivers. All constants are taken from the
corresponding Linux driver.
This driver supports clock rate setting only debug UART,
RGMII/Ethernet modules and USB controller.
Co-authored-by: Volodymyr Babchuk <volodymyr_babchuk@epam.com>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Julius Lehmann <lehmanju@devpi.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
The existing code is unnecessarily convoluted:
Arrays __prci_init_clocks_fu[5|7]40 are initialized with data.
In separate includes fu[5|7]40-prci.h the size of the arrays is provided as
constants.
By moving the structures prci_clk_fu[5|7]40 to the respective code modules
we can directly use ARRAY_SIZE() to access the size of the data used for
initialization.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
If multiple messages are written, line-feeds improve the readability.
Fixes: c40b6df87f ("clk: Add SiFive FU540 PRCI clock driver")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Provide a function to locate this information, rather than doing it
automatically on startup, to save space in global_data.
Signed-off-by: Simon Glass <sjg@chromium.org>
