Add the definition of the pinctrl for the MCU domain.
Same as kernel commit 500e6dfbb465531150ac6e2ff0856dd357ddc8a4
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
The PMC node is not an interrupt provider, so it must not have
interrupt-cells.
This fixes the warning (on newer DTC):
arch/arm/dts/sama5d2.dtsi:82.22-602.6: Warning (interrupt_provider): /ahb/apb/pmc@f0014000: '#interrupt-cells' found, but node is not an interrupt provider
Fixes: 2c4b2dd289 ("ARM: at91/dt: Add device tree for SAMA5D2 Xplained")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
The i2c locks up when initialized before relocation, and it stays broken
in Linux as well breaking the ability to boot Linux.
The i2c bus and pmic was not actually used in pre-reloc before
commit ad607512f5 ("power: pmic: rk8xx: Support sysreset shutdown method")
The cause is not known.
This is board-specific, other boards that do not add the option to
include the i2c bus in pre-reloc DT are not affected.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The GPT table is taking the first 34 sectors, which amounts to 0x4400
bytes. Saving the environment below this address in storage will corrupt
the GPT table.
While technically the table ends at 0x4400, some tools (e.g. bmaptool)
are rounding everything to the logical block size (0x1000), so it is
safer to make it point to 0x5000 so that the environment could still
persist when flashing a sparse image with bmaptool or similar tools.
Obviously, the default 0x4000 environment size does not work anymore, so
let's set it to 0x3000 so it does fill the gap between the GPT table
(rounded to 0x1000) and the start of the idbloader.img.
Fixes: 56f580d3eb ("rockchip: dts: rk3399-puma: put environment (in MMC/SD configurations) before SPL")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Move all rk3128 u-boot specific properties in separate dtsi files.
Sort emmc node.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to update the DT for rk3128
sync the clock dt-binding header.
This is the state as of v6.0 in Linux.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip platform use TPL to do the DRAM initialize for all the SoCs,
if TPL is not available, means no available DRAM init program, and the
u-boot-rockchip.bin is not functionable.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Change-Id: I2299f1eddce5aa7d5fb1a3fb4d8aeaa995b397fa
Add OSPI Support such that this device can boot up using OSPI Flash.
Also can use the flash for other purposes if required from uboot.
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Introduce the base dts files needed for u-boot or to augment the
linux dtbs for use in the u-boot-spl and u-boot binaries
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Introduce the basic am62a7 SoC dtbs from the v6.1-rc3 tag of the linux
kernel along with the new am62a specific pinmux definition that we will
use to generate the dtbs for the u-boot-spl and u-boot binaries
Co-developed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
- Drop MMCI interrupt-names in STM32H743, STM32MP15 and STM322MP13 DT
DHSOM:
- Enable assorted ST specific commands
- Add version variable
- Add boot counter
STM32MP13:
- Add sdmmc cd-gpios for STM32MP135F-DK
- Add clock & reset support
STM32 ADC:
- Split channel init into several routines
- Add support of generic channels binding
Enable the EBI and NAND flash controller. Define the pinctrl and
partition table
Signed-off-by: Balamanikandan Gunasundar <balamanikandan.gunasundar@microchip.com>
Second set of u-boot-at91 fixes for the 2023.01 cycle:
This is a single tiny fix that allows the correct name for one pin on
sama7g5 device. People with DT coming from Linux will have build errors
without this if they add NAND device.
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The SanCloud BBE requires the same dtb nodes to be present in the SPL as
the AM335x EVM.
The SanCloud BBE Lite also requires the SPI flash node and all
dependencies to be present in the SPL to support SPI boot.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
For successful boot when CONFIG_SPL_OF_CONTROL=y, we need to ensure that
the board EEPROM on i2c0, the uart0 serial port and the relevant boot
device (mmc1 or mmc2) can be accessed in the SPL. We also need to
preserve the parent nodes for each required dtb node.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
The signal name of pin PD8 with function D is A22_NANDCLE
as it is defined in the datasheet.
Fixes: 558378a4cd ("ARM: mach-at91: add support for new SoC sama7g5")
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Add configuration file for mini u-boot configuration which runs on a
smaller footprint from on chip memory(OCM). This configuration has
required CONFIG's enabled to support octal spi flash and uses DCC terminal
for console output. Add required dts for octal spi flash mini u-boot
configuration.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20221116141155.14788-4-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
We should guard the SPL nodes against CONFIG_SPL_BUILD to fix
the following build error when the blobs are absent:
binman: Fail open first container file mx8qm-ahab-container.img
Signed-off-by: Fabio Estevam <festevam@denx.de>
Originally, the mmc aliases node was present in imx6qdl-wandboard.dtsi.
After the sync with Linux in commit d0399a46e7 ("imx6dl/imx6qdl:
synchronise device trees with linux"), the aliases node is gone as
the upstream version does not have it.
This causes a regression in which the SD card cannot be found anymore:
Since commit the aliases node has been removed
U-Boot 2022.10-00999-gcca41ed3d63f-dirty (Nov 03 2022 - 22:07:38 -0300)
CPU: Freescale i.MX6QP rev1.0 at 792 MHz
Reset cause: POR
DRAM: 2 GiB
Core: 62 devices, 17 uclasses, devicetree: separate
PMIC: PFUZE100 ID=0x10
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... MMC: no card present
*** Warning - No block device, using default environment
Fix it by passing the alias node in the u-boot.dtsi file to
restore the original behaviour where the SD card (esdhc3) was
mapped to mmc0.
Fixes: d0399a46e7 ("imx6dl/imx6qdl: synchronise device trees with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
