Some Winbond SPI NORs have special SR3 register which is
used among other things to control whether non-standard
"Individual Block/Sector Write Protection" (WPS bit)
locking scheme is activated. This non-standard locking
scheme is not supported by either U-Boot or Linux SPI
NOR stack so make sure it is disabled, otherwise the
SPI NOR may appear locked for no obvious reason.
This SR3 WPS appears e.g. on W25Q16FW which has the same ID as
W25Q16DW, but the W25Q16DW does not implement the SR3 WPS bit.
Signed-off-by: Marek Vasut <marex@denx.de>
In parallel mode, the current implementation assumes that a maximum of
two flashes are connected. The QSPI controller splits the data evenly
between both the flashes so, both the flashes that are connected in
parallel mode should be identical.
During each operation SPI-NOR sets 0th bit for CS0 & 1st bit for CS1 in
nor->flags.
In stacked mode the current implementation assumes that a maximum of two
flashes are connected and both the flashes are of same make but can
differ in sizes. So, except the sizes all other flash parameters of both
the flashes are identical
Spi-nor will pass on the appropriate flash select flag to low level
driver, and it will select pass all the data to that particular flash.
Write operation in parallel mode are performed in page size * 2 chunks as
each write operation results in writing both the flashes. For doubling
the address space each operation is performed at addr/2 flash offset,
where addr is the address specified by the user.
Similarly for read and erase operations it will read from both flashes,
so size and offset are divided by 2 and send to flash.
Adding the config option SPI_ADVANCE for non SPL code.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
MTD block - abstraction over MTD subsystem, allowing
to read and write in blocks using BLK UCLASS.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d, reversing
changes made to 2ee6f3a5f7.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Convert UTF-8 chars to ASCII in cases where make sense. No Copyright or
names are converted.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Marek Behún <kabel@kernel.org>
Introduced in upstream Linux with commit 7a08dbaedd365 for release v5.0.
When the new atmel nand driver was backported to U-Boot with commit
6a8dfd5722 ("nand: atmel: Add DM based NAND driver") that definition
was added to the driver instead of the header file. Move it over to the
other definitions with the same help text it has in Linux.
Code actually using this has not been ported over to raw nand base yet.
Link: https://lore.kernel.org/all/20240320090214.40465-3-ada@thorsis.com
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Enabling Octal DTR mode in multi-die package parts requires reister setup
for each die. That can be done by simple for-loop. write_enable() takes
effect to all die at once so we can call it before the loop. Besides we
can replace spi_mem_exec_op() calls with spansion_read/write_any_reg().
And finally, we must mask CFR2V[7:4] when changing dummy cycles, as
CFR2V[7] indicates current addressing mode and that should be 1 (4-byte
address mode) for multi-die package parts.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Infineon(Cypress) S28Hx-T family does not support legacy CLSR(0x30) opcode.
Instead, it supports CLPEF(0x82) which has the same functionality as CLSR.
spansion_sr_ready() is for multi-die package parts including S28HS02GT, so
we need to use CLPEF instead of CLSR.
This change does not affect to S25x02GT which uses spansion_sr_ready() as
S25Hx-T family also supports CLPEF(0x82) as well as CLSR(0x30).
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
s25_erase_non_uniform() and s28hx_t_erase_uniform() support hybrid sector
layout (32 x 4KB sectors overlaid at bottom address) and doing same thing.
Consolidate them into single helper named s25_s28_erase_non_uniform().
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Some macro definitions used in Infineon(Cypress) S25 and S28 series are
redundant and some have inconsistent prefix. This patch removes
redundant ones and renames some to have same prefix as others.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
To quote the author:
This series tests raw nand flash in sandbox and fixes various bugs discovered in
the process. I've tried to do things in a contemporary manner, avoiding the
(numerous) variations present on only a few boards. The test is pretty minimal.
Future work could test the rest of the nand API as well as the MTD API.
Bloat (for v1) at [1] (for boards with SPL_NAND_SUPPORT enabled). Almost
everything grows by a few bytes due to nand_page_size. A few boards grow more,
mostly those using nand_spl_loaders.c. CI at [2].
[1] https://gist.github.com/Forty-Bot/9694f3401893c9e706ccc374922de6c2
[2] https://source.denx.de/u-boot/custodians/u-boot-clk/-/pipelines/18443
This allows using these functions without ifdefs. OneNAND depends on MTD,
so this ifdef was redundant in the first place.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
At this point, we don't need to have <common.h> be included because of
properties in the header itself, it only includes other common header
files. We've also audited the code enough at this point that we can drop
<common.h> from being included in headers and rely on code to have the
correct inclusions themselves, or at least <common.h>.
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently there are 3 different variants of read_id implementation:
1. opcode only. Found in GD5FxGQ4xF.
2. opcode + 1 addr byte. Found in GD5GxGQ4xA/E
3. opcode + 1 dummy byte. Found in other currently supported chips.
Original implementation was for variant 1 and let detect function
of chips with variant 2 and 3 to ignore the first byte. This isn't
robust:
1. For chips of variant 2, if SPI master doesn't keep MOSI low
during read, chip will get a random id offset, and the entire id
buffer will shift by that offset, causing detect failure.
2. For chips of variant 1, if it happens to get a devid that equals
to manufacture id of variant 2 or 3 chips, it'll get incorrectly
detected.
This patch reworks detect procedure to address problems above. New
logic do detection for all variants separatedly, in 1-2-3 order.
Since all current detect methods do exactly the same id matching
procedure, unify them into core.c and remove detect method from
manufacture_ops.
This is a rework of Chuanhong Guo <gch981213@gmail.com> patch
submitted to linux kernel
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/all/20230110115843.391630-1-frieder@fris.de
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
As part of various code clean-ups we have on occasion missed removing
unused header files. None of these files are referenced anywhere else
at this point.
Signed-off-by: Tom Rini <trini@konsulko.com>
This is not used since this commit:
570c3dcfc1 arm: Remove spear600 boards and the rest of SPEAr support
Drop the driver and Kconfig option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
This is not used since this commit:
8d1e3cb140 powerpc: mpc83xx: remove MPC8360ERDK, EMPC8360EMDS support
Drop the driver and Kconfig option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-By: Michael Trimarchi <michael@amarulasolutions.com>
Infineon S25FS256T is 256Mbit Quad SPI NOR flash. The key features and
differences comparing to other Spansion/Cypress flash familes are:
- 4-byte address mode by factory default
- Quad mode is enabled by factory default
- Supports mixture of 128KB and 64KB sectors by OTP configuration
(this patch supports uniform 128KB only)
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cypress defines two flavors of configuration registers, volatile and
non volatile, and both use the same bit fields. Rename the bitfields in
the configuration registers so that they can be used for both flavors.
Suggested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
CFR5[6] is reserved bit and must be always 1. Set it to comply with flash
requirements. While fixing SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_EN definition,
stop using magic numbers and describe the missing bit fields in CFR5
register. This is useful for both readability and future possible addition
of Octal STR mode support.
Fixes: ea9a22f7e7 ("mtd: spi-nor-core: Add support for Cypress Semper flash")
Suggested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The GPMC is a unified memory controller dedicated for interfacing
with external memory devices like
- Asynchronous SRAM-like memories and ASICs
- Asynchronous, synchronous, and page mode burst NOR flash
- NAND flash
- Pseudo-SRAM devices
This driver will take care of setting up the GPMC based on
the settings specified in the Device tree and then
probe its children.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
The nor->addr_width tracks number of address bytes used in
read/program/erase ops and eventually set to 4 for >16MB chips, regardless
of flash's internal address mode. For Infineon SEMPER flash's, we use
Read/Write Any Register commands for configuration and status check.
These commands take 3- or 4-byte address depending on flash's internal
address mode.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Upstream linux commit 7bb427990ee364.
Rename the function to match this new behavior.
NOTE: fix nand_detect/nand_get_flash_type parameters in
mxs_nand_spl. This code seems never executed by any board
as alternative for nand detect
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 4722c0e958e636.
The returned "type" is never used in nand_scan_ident() and spl code
Make nand_get_flash_type() simply return an integer value in order
to avoid unnecessary ERR_PTR/PTR_ERR dance.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 3b5206f4be9b65.
Move Macronix specific initialization logic into nand_macronix.c. This
is part of the "separate vendor specific code from core" cleanup
process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 229204da53b31d.
Move AMD/Spansion specific initialization/detection logic into
nand_amd.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 10d4e75c36f6c1.
Move Micron specific initialization logic into nand_micron.c. This is
part of the "separate vendor specific code from core" cleanup process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 9b2d61f80b060c.
Move Toshiba specific initialization and detection logic into
nand_toshiba.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 01389b6bd2f4f7.
Move Hynix specific initialization and detection logic into
nand_hynix.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit c51d0ac59f2420.
Move Samsung specific initialization and detection logic into
nand_samsung.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit abbe26d144ec22.
A lot of NANDs are implementing generic features in a non-generic way,
or are providing advanced auto-detection logic where the NAND ID bytes
meaning changes with the NAND generation.
Providing this vendor specific initialization step will allow us to get
rid of full-id entries in the nand_ids table or all the vendor specific
cases added over the time in the generic NAND ID decoding logic.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 7f501f0a72036d.
Store the NAND ID in struct nand_chip to avoid passing id_data and id_len
as function parameters.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
There was no user of this callback after 5b66fdb29d anymore, and its
semantic as now inconsistent between stm and sst26. What we need for the
upcoming new usecase is a "completely unlocked" semantic. So consolidate
over this.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
