210ab4f60d
The NanoPi RK3399 boards support UHS-I (up to SDR104) SD cards, however using any of these 1.8v modes results in a boot failure in SPL upon soft reboot. The issue is that the "vcc_sdio" regulator is left at 1.8v on reboot and the corresponding GPIO defaults to 3.3v. This prevents the SD card from being reinitialized and read successfully. This change enables the RK8XX regulators and Rockchip IO-domain drivers in SPL, which initializes "vcc_sdio" regulator to 3.0v and configures the GPIO for the correct level on boot. Signed-off-by: Justin Klaassen <justin@tidylabs.net> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
85 lines
2.1 KiB
Plaintext
85 lines
2.1 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_SKIP_LOWLEVEL_INIT=y
|
|
CONFIG_COUNTER_FREQUENCY=24000000
|
|
CONFIG_ARCH_ROCKCHIP=y
|
|
CONFIG_SPL_GPIO=y
|
|
CONFIG_NR_DRAM_BANKS=1
|
|
CONFIG_ENV_OFFSET=0x3F8000
|
|
CONFIG_DEFAULT_DEVICE_TREE="rockchip/rk3399-nanopi-m4b"
|
|
CONFIG_DM_RESET=y
|
|
CONFIG_ROCKCHIP_RK3399=y
|
|
CONFIG_SPL_DRIVERS_MISC=y
|
|
CONFIG_TARGET_EVB_RK3399=y
|
|
CONFIG_SYS_LOAD_ADDR=0x800800
|
|
CONFIG_DEBUG_UART_BASE=0xFF1A0000
|
|
CONFIG_DEBUG_UART_CLOCK=24000000
|
|
CONFIG_PCI=y
|
|
CONFIG_DEBUG_UART=y
|
|
CONFIG_AHCI=y
|
|
CONFIG_DEFAULT_FDT_FILE="rockchip/rk3399-nanopi-m4b.dtb"
|
|
CONFIG_DISPLAY_BOARDINFO_LATE=y
|
|
CONFIG_SPL_MAX_SIZE=0x40000
|
|
# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
|
|
CONFIG_SPL_I2C=y
|
|
CONFIG_SPL_POWER=y
|
|
CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y
|
|
CONFIG_TPL=y
|
|
CONFIG_CMD_BOOTZ=y
|
|
CONFIG_CMD_GPT=y
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_PCI=y
|
|
CONFIG_CMD_USB=y
|
|
# CONFIG_CMD_SETEXPR is not set
|
|
CONFIG_CMD_TIME=y
|
|
CONFIG_SPL_OF_CONTROL=y
|
|
CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
|
|
CONFIG_ENV_IS_IN_MMC=y
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_SCSI_AHCI=y
|
|
CONFIG_AHCI_PCI=y
|
|
CONFIG_ROCKCHIP_GPIO=y
|
|
CONFIG_SYS_I2C_ROCKCHIP=y
|
|
CONFIG_SPL_ROCKCHIP_IODOMAIN=y
|
|
CONFIG_MMC_DW=y
|
|
CONFIG_MMC_DW_ROCKCHIP=y
|
|
CONFIG_MMC_SDHCI=y
|
|
CONFIG_MMC_SDHCI_SDMA=y
|
|
CONFIG_MMC_SDHCI_ROCKCHIP=y
|
|
CONFIG_PHY_REALTEK=y
|
|
CONFIG_DM_ETH_PHY=y
|
|
CONFIG_ETH_DESIGNWARE=y
|
|
CONFIG_GMAC_ROCKCHIP=y
|
|
CONFIG_NVME_PCI=y
|
|
CONFIG_PHY_ROCKCHIP_INNO_USB2=y
|
|
CONFIG_PHY_ROCKCHIP_TYPEC=y
|
|
CONFIG_PMIC_RK8XX=y
|
|
CONFIG_SPL_PMIC_RK8XX=y
|
|
CONFIG_SPL_DM_REGULATOR=y
|
|
CONFIG_SPL_DM_REGULATOR_FIXED=y
|
|
CONFIG_REGULATOR_RK8XX=y
|
|
CONFIG_SPL_REGULATOR_RK8XX=y
|
|
CONFIG_PWM_ROCKCHIP=y
|
|
CONFIG_SCSI=y
|
|
CONFIG_BAUDRATE=1500000
|
|
CONFIG_DEBUG_UART_SHIFT=2
|
|
CONFIG_SYS_NS16550_MEM32=y
|
|
CONFIG_SYSRESET=y
|
|
CONFIG_USB=y
|
|
CONFIG_USB_XHCI_HCD=y
|
|
CONFIG_USB_EHCI_HCD=y
|
|
CONFIG_USB_EHCI_GENERIC=y
|
|
CONFIG_USB_DWC3=y
|
|
CONFIG_USB_DWC3_GENERIC=y
|
|
CONFIG_USB_KEYBOARD=y
|
|
CONFIG_USB_HOST_ETHER=y
|
|
CONFIG_USB_ETHER_ASIX=y
|
|
CONFIG_USB_ETHER_ASIX88179=y
|
|
CONFIG_USB_ETHER_MCS7830=y
|
|
CONFIG_USB_ETHER_RTL8152=y
|
|
CONFIG_USB_ETHER_SMSC95XX=y
|
|
CONFIG_VIDEO=y
|
|
CONFIG_DISPLAY=y
|
|
CONFIG_VIDEO_ROCKCHIP=y
|
|
CONFIG_DISPLAY_ROCKCHIP_HDMI=y
|
|
CONFIG_ERRNO_STR=y
|