blog: jackson pad: editing pass
This commit is contained in:
parent
da73b1b226
commit
58bc97fc98
|
@ -15,42 +15,43 @@ i received my first ever noise complaint!
|
|||
although electronic sets are audibly quieter, they still transmit a lot of energy
|
||||
into the floor. when struck, vibrations carry from the drum into
|
||||
the harness and from there into the floor. moreover, the kick and high-hat
|
||||
pedal action mirrors the same action a person would make when stomping, so of
|
||||
*course* that's going to annoy a downstairs neighbor.
|
||||
pedal action mirrors that of a person stomping, so of
|
||||
*course* that's going to annoy the downstairs neighbor.
|
||||
|
||||
# Options to decrease vibrations
|
||||
## How to decrease vibrations
|
||||
|
||||
the most straightforward way to decrease floor vibrations is to decrease
|
||||
the energy associated with each drum hit.
|
||||
the energy associated with each hit.
|
||||
for example, use [beaterless pedals](https://www.amazon.com/Yamaha-KU100-Beaterless-Silent-Pedal/dp/B00FI2PE1U).
|
||||
if there's no beater imparting energy into kick plate,
|
||||
that's obviously going to result in less energy transmitted into the floor.
|
||||
if there's no beater imparting energy into kick plate then
|
||||
that's less energy transmitted into the floor.
|
||||
similarly, slamming the high-hat close imparts momentum from the upper cymbal
|
||||
into the stand and from there to the floor.
|
||||
beaterless pedals solve both these issues.
|
||||
|
||||
![Yamaha KU100 beaterless pedal](yamaha-ku100-beaterless-pedal.jpg)
|
||||
|
||||
but even with beaterless pedals, you still have the issue of snare/tom hits
|
||||
vibrating through the harness. if you want to stop all these,
|
||||
you'll need an isolation platfrom [like this](https://www.thomann.de/gb/thomann_drum_noise_elimination_podium.htm).
|
||||
but even with beaterless pedals (if you're willing to go that route),
|
||||
you still have the issue of snare/tom hits vibrating through the harness.
|
||||
if you want to stop all these, you'll need an isolation platfrom
|
||||
[like this](https://www.thomann.de/gb/thomann_drum_noise_elimination_podium.htm):
|
||||
|
||||
![](thomann-drum-noise-elimination-podium.jpg)
|
||||
|
||||
or you can place the set atop a riser.
|
||||
or you can place the set atop a riser:
|
||||
|
||||
![](drum-riser.jpg)
|
||||
|
||||
i was very tempted by that Thomann podium, but it's priced a bit too aggressively for me.
|
||||
|
||||
cheaper options include placing the set on a big rubber or foam pad, similar
|
||||
cheaper options include placing the set on a large rubber or foam pad, similar
|
||||
to what you might put under a washing machine or an exercise bike ("anti vibration mats").
|
||||
|
||||
but after browsing drum forums i couldn't find many success stories from these approaches.
|
||||
maybe that's just a bias from the people who frequent these forums and anti-vibration mats
|
||||
work equally well, but i was intrigued by the other approaches i saw there.
|
||||
|
||||
# DIY solutions
|
||||
## DIY solutions
|
||||
|
||||
the most infamous DIY approach within these drum communities is the *tennis ball riser*:
|
||||
sandwich tennis balls between two large panels (or a panel and the floor), put the drumset
|
||||
|
@ -62,7 +63,7 @@ creator (Brian Jackson) provides detailed build instructions, some convincing
|
|||
noise measurements, a believable theory of operation, and i couldn't find anyone
|
||||
who tried this *without* success.
|
||||
|
||||
# The Jackson Pad
|
||||
## The Jackson Pad
|
||||
|
||||
initially proposed [on vdrums.com](https://www.vdrums.com/forum/advanced/diy/1095500-new-design-impact-isolating-platform-plans-and-guide),
|
||||
i've mirrored the original [design document](./jackson-pad/Jackson%20Pad%20-%20Design%20Drawings%20-%202-10-2015.pdf)
|
||||
|
@ -79,24 +80,24 @@ transforming mechanical energy into heat energy (compressing a gas causes it to
|
|||
the heat will be transformed back into mechnical energy as the pressures balance,
|
||||
but the effect is that sharp impulses of mechanical energy are imparted into the
|
||||
floor over a longer period of time.
|
||||
it's like applying a low-pass filter to original foot stomping.
|
||||
it's like applying a low-pass filter to the original foot stomp or drum hit.
|
||||
|
||||
i'm a little skeptical of the heat argument, but overall i'm satisfied enough
|
||||
with the theory of operation to give it a try.
|
||||
|
||||
# Construction
|
||||
## Construction
|
||||
|
||||
the pad materials are super practical to source. it's all off-the-shelf lumber
|
||||
that you can buy at a hardware store with a minimal number of cuts.
|
||||
the stock 4'x4.7' design is just large enough
|
||||
for a typical 4-drum + highhat + kick + ride + crash configuration with a stool that
|
||||
doesn't have a huge footprint.
|
||||
for a typical 4-drum + highhat + kick + ride + crash configuration and a stool
|
||||
with modest footprint.
|
||||
|
||||
unfortunately, it's just large enough to not be practical to move around in a car.
|
||||
unfortunately, it's just large enough to not be practical to transport.
|
||||
i move homes every year or two, so i wanted to find a way to make it fit in
|
||||
my stationwagon.
|
||||
|
||||
the stock plan is makes use of four 55.5" trusses which support fourteen 2x4s running
|
||||
the stock plan makes use of four 55.5" trusses which support fourteen 2x4s running
|
||||
perpindicular to them:
|
||||
|
||||
![Original Jackson Pad](plans-clean.png)
|
||||
|
@ -108,12 +109,16 @@ which would secure the halves when bolted. with the bolts in place, you're left
|
|||
a solid 48"x55.5" pad; with the bolts removed, you have two smaller pads that can
|
||||
be easily transported.
|
||||
|
||||
the original design leaves four 40" boards of scrap from cutting the trusses.
|
||||
you can trim these down to 2' and use those as the braces. the only addition to
|
||||
Jackson's BOM is sixteen 4" bolts, washers, and wingnuts.
|
||||
|
||||
here's what the truss + brace system looks like when bolted together:
|
||||
|
||||
![](trusses-bolted-together.jpg)
|
||||
|
||||
when constructing the platform, keep the bolts in place and secure the 2x4s atop
|
||||
each truss as normal (make sure to screw them into the trusses, and _not_ the braces)!
|
||||
each truss as normal (make sure to secure the slats onto the trusses, and _not_ the braces -- otherwise you won't be able to detach the braces!)
|
||||
|
||||
![](first-2x4-secured.jpg)
|
||||
|
||||
|
@ -135,7 +140,9 @@ you can cut one piece of carpet to the full 48"x55.5", staple it, and let it fol
|
|||
during disassembly. it'll take two people to carry it this way, but it probably looks
|
||||
nicer when assembled than if you carpeted each half separately.
|
||||
|
||||
when you're ready, just unbolt the braces, slide them off, and then fold the platform:
|
||||
## Disassembly & Reassembly
|
||||
|
||||
when you're ready, just unbolt the braces, slide them off, and fold the platform:
|
||||
|
||||
![](folded-1.jpg)
|
||||
|
||||
|
|
Loading…
Reference in New Issue