Include the new SAR interface in the build so that gdbus-codegen
generates support for it in libmm-glib as well as proper documentation
in the API reference.
Add a new D-Bus interface to support dynamic SAR across multiple platforms.
The new interface exposes methods to configure sar power levels,
handle the communications with the modem, and let the platform
code be agnostic to modem type.
This property will be TRUE if the bearer has the data session
connected through a multiplexed interface.
If the bearer is disconnected, or connected without multiplexing, the
property will report FALSE.
In addition to the amount of bearers a user may connect without
multiplexing enabled (the default until now), we now also expose the
maximum number of bearers a user may connect after enabling
multiplexing over one single network interface (if supported).
The method responsible for creating the MMBearerList is now also
subclassable, so that implementations supporting multiplexing can
provide their own version with their own thresholds.
This property was never initialized with a correct value, we would
always use the same value as used for MaxActiveBearers, which isn't
technically right. Just suggest to ignore this property, and flag
it as deprecated.
In addition to deprecating the API property, we will internally no
longer limit the amount of bearer objects that may be created with
different connection settings. The bearer object exposed in DBus is a
representation of the connection that may be setup, and so we can hold
as many representations as we want as long as the amount of connected
bearers doesn't exceed the maximum amount for each modem.
Leaving around the disconnected modems also serves another purpose.
Each bearer holds information about the amount of times a connection
with it has been attempted, and the amount of data transferred through
it. If we use the Simple.Connect() method to connect the modem using
different bearer settings, we won't lose the information of the past
connection attempts with different settings.
Both the Simple.Connect() and Modem.CreateBearer() are updated to
allow a new 'multiplex' setting in the properties provided by the user
in both of these methods.
The new setting expects a MMBearerMultiplexSupport enum indicating
what kind of multiplex needs the user has:
* none: if multiplex must not be used.
* requested: if multiplex should be used if available.
* required: if multiplex must be used.
The underlying implementations will take care of accepting or
rejecting the setting depending on the system and modem capabilities.
The ModemManager1.Sim.PreferredNetworks property contains the preferred
networks (and access technologies, if available) configured to the
SIM card.
This commit implements preferred networks reading with AT+CPOL.
This setting is unused since some releases ago, and the corresponding
libmm-glib methods were already flagged as deprecated. Let's add an
explicit mention to this deprecation on the DBus API itself.
If e.g. a bearer with IPv6 configuration has DNS servers but exports
its link-local address, MM will avoid giving it the "static" method
type, and instead fall back to the "dhcp" type. However, it may
still have DNS information. Therefore, the comment that "method" is
the only property on configuration with type DHCP is misleading.
This new method allows changing the SIM slot considered as primary,
when the modem supports multiple SIM slots.
The generic handling of this method will make sure that the modem
object and all its SIM objects are re-probed from scratch as soon as a
successful SIM slot switch happens.
Implementations may report MM_CORE_ERROR_EXISTS when the switch
doesn't need to happen (e.g. if the requested SIM slot is already the
active one).
The 'SimSlots' property exposes an array of SIM object paths, with one
array item for each available SIM slot in the system. If a valid SIM
card is found in a given slot, the path of the SIM object will be
exposed in the array item; if no valid SIM card is found, the empty
object path ("/") will be exposed instead.
The 'PrimarySimSlot' property exposes which of the SIM slots available
in the system is the one configured as being primary. In a Multi-SIM
Single-Standby setup, the primary slot will be the one corresponding
to the single active SIM in the system. In a Multi-SIM Multi-Standby
setup, the primary slot will be the one configured to act as primary
(e.g. the one that will be used for the data connection) among all the
active SIM cards found.
In preparation for the multi-SIM setup, we need a way to tell whether
a given SIM card is active or not in the system.
On systems with one single SIM slot, the available SIM card will
always be active.
On Multi-SIM Single-Standby setups we may have multiple SIM slots with
multiple SIM cards, but only one of them will be active at any given
time.
On Multi-SIM Multi-Standby setups we may have multiple SIM slots with
multiple SIM cards that may be active at the same time. E.g. the QMI
protocol allows up to 5 different active SIM cards (primary,
secondary, tertiary...).
Extended the ModemManager Signal interface to include 5G signal
information for RSRP, RSRQ and SINR via libqmi. Also extended mmci
to print 5G signal info.
In the D-Bus specification it is stated that the root node of
an introspection file should have an absolute path[1]. This path
should not be the root path in D-Bus as putting objects there is
considered incorrect, and also because the MM1 object does not
actually sit at the root path (instead, it uses MM_DBUS_PATH, which
is /org/freedesktop/ModemManager1). Fix this in the introspection
file.
[1] https://dbus.freedesktop.org/doc/dbus-specification.html#introspection-format
When we're reusing over and over the same bearer object, we can
provide statistical information about the number of connection
attempts that have been done and how many of them failed.
This new flag allows users of the API to know whether general purpose
voice calls are allowed or otherwise only voice calls to the
registered emergency numbers should be performed.
ModemManager won't really do any distinction between emergency and
non-emergency calls at this point, this flag is just an early
indication for the user of the API that no normal voice call should be
attempted.
These new methods allow querying and updating the status of the call
waiting network service, as per 3GPP TS 22.083.
The status of the service is not a property because we don't want to
unconditionally load it on every boot, given that the process involves
talking to the network (i.e. it is not a device setting).
This method will join all active and held calls into a single
multiparty call, and then request the network to terminate the call on
the subscriber's end and transfer the control of the call to the
parties that are still in the call.
This method will put the currently active call on hold, and right away
accept the next available call.
The user of the API does not need to specify explicitly which is the
next call to accept, because that is decided automatically:
* If there is any waiting call, it will accept it right away.
* If there is no waiting call but there is a held call, it will make
the held call active again.
This method will hangup the currently active call and right away
accept the next available call.
The user of the API does not need to specify explicitly which is the
next call to accept, because that is decided automatically:
* If there is any waiting call, it will accept it right away.
* If there is no waiting call but there is a held call, it will make
the held call active again.
