Previously PLL node was missing from SPL dts. This caused BUS_ROOT
to stay on OSC clock (24Mhz). As a result, all peripherals have to
run at a much lower frequency, and loading from sdcard/emmc is slow.
Thus, enabling PLL node in dts to fix this.
Signed-off-by: Bo Gan <ganboing@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
It appears that there is some timing marginality either in the
board layout or the SoC that results in occasional data corruption
on some boards.
We observed this issue on some of the new HiFive Unmatched RevB
boards during volume production as well as some of the original
HiFive Unmatched boards from 2021 in our possession. This means
that there are other boards out there that might have the issue
too.
We have done some limited testing with DDR4 at 1600MT/s and
faulty boards (failing at 1866MT/s) passed.
We plan further testing after we procure a temperature chamber.
Signed-off-by: Thomas Perrot <thomas.perrot@bootlin.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add the axp15060 regulator device. OpenSBI uses this device to perform
board reset and shutdown.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
JH7110 has a power management unit controller node. Add this node.
This device is used by OpenSBI during board reset/shutdown.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Import device tree from Linux kernel to add basic support for CPU, PLIC,
UART and Timer. The name cv1800b in the filename represent the chip used
on Milk-V Duo board.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Extend compatible string to match the latest change in dt binding.
Fixes: 7576ab2fac ("riscv: Add support for AMD/Xilinx MicroBlaze V")
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
MicroBlaze V is new AMD/Xilinx soft-core 32bit RISC-V processor IP.
It is hardware compatible with classic MicroBlaze processor.
The patch contains initial wiring and configuration for initial HW design
with memory, cpu, interrupt controller, timers and uartlite console
(interrupt controller is listed but U-Boot is not using it).
Provided DT is just describing one configuration and should be taken only
as example.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Add gpio-restart node to do reset.
Before applied this patch, System Reset Extension doesn't appear with
sbi command.
OpenSBI 1.3
Machine:
Vendor ID 489
Architecture ID 8000000000000007
Implementation ID 4210427
Extensions:
sbi_set_timer
sbi_console_putchar
...[snip]...
IPI Extension
RFENCE Extension
Hart State Management Extension
Performance Monitoring Unit Extension
After applied this patch, System Reset Extension is supported from SBI.
OpenSBI 1.3
Machine:
Vendor ID 489
Architecture ID 8000000000000007
Implementation ID 4210427
Extensions:
sbi_set_timer
sbi_console_putchar
...[snip]...
IPI Extension
RFENCE Extension
Hart State Management Extension
System Reset Extension
Performance Monitoring Unit Extension
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This copies in some devicetree files from the official Linux kernel tree,
v6.6-rc6. It covers a board with the Allwinner T113s SoC, which shares
many devices with its RISC-V sibling, the Allwinner D1(s). This is the
reason for the core .dtsi files landing in the arch/riscv directory.
We are only adjusting the include path to accommodate for the differences
in the U-Boot build system.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Add condition for OpenSBI OS boot mode, by default it is not enabled.
By default, binman creates the output file u-boot.itb.
If SPL_OPENSBI_OS_BOOT is enabled, linux.itb will be created
after compilation instead of the default u-boot.itb.
Signed-off-by: Randolph <randolph@andestech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some platforms may not have any DDR memory below 4G and for such platforms
the TEXT_BASE and LOAD addresses etc are all 64 bit addresses due to
which the u-boot build fails with below error:
u-boot/arch/riscv/dts/binman.dtsi:30.14-25
Value out of range for 32-bit array element
u-boot/arch/riscv/dts/binman.dtsi:43.14-25
Value out of range for 32-bit array element
u-boot/arch/riscv/dts/binman.dtsi:44.15-26
Value out of range for 32-bit array element
FATAL ERROR: Syntax error parsing input tree
Fix by setting the address-cells property to 2 and converting load
addresses to 64 bit values.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The StarFive VisionFive 2 board cannot load spl/u-boot-spl.bin but needs a
prefixed header. We have referring to a vendor tool (spl_tool) for this
task. 'mkimage -T sfspl' can generate the prefixed file.
Use binman to invoke mkimage for the generation of file
spl/u-boot-spl.bin.normal.out.
Update the documentation.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tested-by: Milan P. Stanić <mps@arvanta.net>
The JH7110 has the arhitectural CPU timer on all 5 rv64 cores.
Note that in the device tree.
Signed-off-by: Torsten Duwe <duwe@suse.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
In StarFive VF2 board. pcie0 connect to VTI usb controller.
Enable it to support usb host.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The difference between 1.2A and 1.3B is dynamically configured according
to the PCB version, and there is no difference on the board device tree,
so the same DT file can be used.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add ethernet device tree node to support StarFive ethernet driver for
the JH7110 RISC-V SoC.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The "notable" disappearances are:
- the pac193x stanza - there's nothing in mainline linux w.r.t. bindings
for this & what is going to appear in mainline linux is going to be
incompatible with what is currently in U-Boot.
- operating points - these operating points should not be set at the
soc.dtsi level as they may not be possible depending on the design
programmed to the FPGA
- clock output names - there are defines for the clock indices, these
should not be needed
- the dt maintainers in linux NAKed using defines for IRQ numbers
- the qspi nand, which is not part of the icicle's default configuration
is removed.
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Tested-by: Padmarao Begari <padmarao.begari@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The original names picked for the DT doesn't match Linux's naming scheme
and it was renamed there a while ago. Rename it in U-Boot to allow
easily syncing dts between the two projects.
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The current ae350-related defconfigs could also
support newer Andes CPU IP, so modify the names of CPU
from ax25 to andesv5, and board name from ax25-ae350 to ae350.
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The initial devicetree for PolarFire SoC incorrectly created a fixed
frequency clock in the devicetree to represent the msspll, but the
msspll is not a fixed frequency clock. The actual reference clock on a
board is either 125 or 100 MHz, 125 MHz in the case of the icicle kit.
Swap the incorrect representation of the msspll out for the actual
reference clock.
Fixes: dd4ee416a6 ("riscv: dts: Add device tree for Microchip Icicle Kit")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Add QSPI NAND device node to the Microchip PolarFire SoC
Icicle kit device tree.
The Winbond NAND flash memory can be connected to the
Icicle Kit by using the Mikroe Flash 5 click board and
the Pi 3 Click shield.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Rick Chen <rick@andestech.com>
In the v2022.10 Icicle reference design, the seg registers have been
changed, resulting in a required change to the memory map.
A small 4MB reservation is made at the end of 32-bit DDR to provide some
memory for the HSS to use, so that it can cache its payload between
reboots of a specific context.
Co-developed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Rick Chen <rick@andestech.com>
As PLICSW is used to trigger the software interrupt, we should rename
Andes PLIC configuration and file name to reflect the usage. This patch
also updates PLMT and PLICSW compatible strings to be consistent with
OpenSBI fdt driver.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
This commit sychronizes the header file for FU740 PRCI clocks with the
one from Linux 5.19.
The constant values are the same, but all constant names are changed
(most are just prefixed with FU740_).
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This adds the onkey, RTC and watchdog children to the DA9063 PMIC node,
fixes the compatible for qspi0's flash node to match the official DT
schema (it being an is25wp256 is discoverable, hence jedec,spi-nor is
the only compatible that should be present) and exposes the card detect
GPIO.
Note that the device trees still diverge in some places (including
important things like the PCIe controller's clock name) and should be
cleaned up so that a common device tree is used in both projects rather
than having different bindings. This patch does not attempt to do that,
merely expose important functionality present in Linux's that is not in
U-Boot's so that it can be used without the OS providing its own bundled
copy.
Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Linux kernel fpioa pinctrl driver expects the sysctl phandle and the
power bit offset of the fpioa device to be specified as a single
property "canaan,k210-sysctl-power".
Replace the "canaan,k210-sysctl" and "canaan,k210-power-offset"
properties with "canaan,k210-sysctl-power" to satisfy the Linux kernel
requirements. This new property is parsed using the existing function
dev_read_phandle_with_args().
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Linux drivers for many of the K210 peripherals depend on the power bus
clock to be specified. Add the missing clocks and their names to avoid
problems when booting Linux using u-boot DT.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
"kendryte" is the marketing name for the K210 RISC-V SoC produced by
Canaan Inc. Rather than "kendryte,k210", use the usual "canaan,k210"
vendor,SoC compatibility string format in the device tree files and
use the SoC name for file names.
With these changes, the device tree files are more in sync with the
Linux kernel DTS and drivers, making uboot device tree usable by the
kernel.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
