All parts expect the SPLL to run at 702MHz. In U-Boot it's the SPLL_HZ
declaring this rate and in the kernel it's a fixed clock definition.
While everything is expecting 702MHz, the SPLL is not running that
frequency when coming from the bootrom though, instead it's running
at 351MHz and the vendor-u-boot just sets it to the expected frequency.
The SPLL itself is located inside the secure-BUSCRU and in theory
accessible as an SCMI clock, though this requires an unknown amount
of cooperation from trusted-firmware to set at a later stage, though
during the SPL stage we can still access the relevant CRU directly.
The SPLL is for example necessary for the DSI controllers to produce
output.
As the SPLL is "just" another rk3588 pll, just set the desired rate
directly during the SPL stage.
Tested on rk3588-rock5b and rk3588-tiger by reading back the PLL rate
and also observing working DSI output with this change.
Fixes: 6737771600 ("rockchip: rk3588: Add support for sdmmc clocks in SPL")
Suggested-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d, reversing
changes made to 2ee6f3a5f7.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Polling cntpct_el0 in a tight loop for delays is inefficient.
This is particularly apparent on Arm FVPs, which do not simulate
real time, meaning that a 1s sleep can take a couple of orders
of magnitude longer to execute in wall time.
If running at EL2 or above (where CNTHCTL_EL2 is available), enable
the cntpct_el0 event stream temporarily and use wfe to implement
the delay more efficiently. The event period is chosen as a
trade-off between efficiency and the fact that Arm FVPs do not
typically simulate real time.
This is only implemented for Armv8 boards, where an architectural
timer exists, and only enabled by default for the ARCH_VEXPRESS64
board family.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
The sev() and wfe() asm macros are currently defined only for
mach-exynos. As these are common Arm instructions, move them to the
common asm/system.h header file, for both Armv7 and Armv8, so they
can be used by other machines.
wfe may theoretically trigger a context switch if an interrupt occurs
so add a memory barrier to this call.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara<andre.przywara@arm.com>
Greg Malysa <greg.malysa@timesys.com> says:
This series adds support for the ADI SC5xx machine type and includes two
core drivers that are required for being able to boot any board--a UART
driver, the gptimer driver which is used as a clock reference (CNTVCNT
is not supported on the armv7 sc5xx SoCs) and the clock tree driver. Our
corresponding Linux support relies on u-boot configuring the clocks
correctly before booting, so it is not possible to boot any board
without the CGU/CDU configuration happening here. There are also no
board files, device trees, or defconfigs included here, but some common
definitions that will be used to build board files currently are. The
sc5xx SoCs themselves include many armv7 families (sc57x, sc58x, and
sc594) all using an ARM Cortex-A5, and one armv8 family (sc598) indended
to be a drop-in replacement for the SC594 in terms of peripherals, with
a Cortex-A55 instead.
Some of the configuration code in dmcinit and clkinit is quite scary and
causes a lot of checkpatch violations. It is modified from code
initially provided by ADI, but it has not been fully rewritten. There's
a question of how important it is to clean up this code--it has some
quality violations, but it has been in use (including in production) for
over two years and is known to work for performing the low level SoC
initialization, while a rewrite might introduce timing or sequence bugs
that could take a significant amount of time to detect in the future.
Add support for the SC5xx machine type from Analog Devices. This
includes support for the SC57x, SC58x, SC59x, and SC59x-64 SoCs, which
have many common features such as common ADI IP blocks, and SHARC DSP
cores. This commit introduces core functionality required for all boards
using an SC5xx SoC, such as:
- SPL configuration
- Required CPU hooks such as reset
- Boot ROM interaction to load the stage 2 bootloader in the reference
configuration. Other options are possible but not officially supported
at this time
- SoC-common configuration expected to be reused by all boards
- Early initialization for system clocks and DDR controller
Co-developed-by: Greg Malysa <greg.malysa@timesys.com>
Signed-off-by: Greg Malysa <greg.malysa@timesys.com>
Co-developed-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas@analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal@analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs@analog.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Remove <common.h> from this board vendor directory and when needed
add missing include files directly.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove <common.h> from this board vendor directory and when needed
add missing include files directly.
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This follows the example of RISC-V where <asm/global_data.h> includes
<asm/u-boot.h> directly as "gd" includes a reference to bd_info already
and so the first must include the second anyhow. We then remove
<asm/u-boot.h> from all of the places which include references to "gd"
an so have <asm/global_data.h> already.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove <common.h> from the remainder of the files under arch/arm and
when needed add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove <common.h> from all fsl-layerscape related files and when needed
add missing include files directly.
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove <common.h> from all mach-imx, CPU specific sub-directories and
include/asm/arch-mx* files and when needed add missing include files
directly.
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove <common.h> from all mach-rockchip and include/asm/arch-rockchip
files and when needed add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove <common.h> from all mach-tegra and include/asm/arch-tegra files
and when needed add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Move cru_rk3308.h and grf_rk3308.h to arch-rockchip to match path used
for all other Rockchip SoCs.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support to get and set the SCLK_RTC32K clock rate.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
[jonas@kwiboo.se: Update commit message]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Not many and nothing really exciting this time: there are more patches
in fly, but they are not ready yet. I will also send some DT updates
and new board defconfig files later, once they have seen the list. I am
aware of the USB rebasing repo efforts, but would like to see how this
plays out, also we have one compatibility issue that I painstakingly
work around in the U-Boot tree for the last three years or so. So for
now I stick to the previous approach.
So now just some easy changes: support for USB peripheral mode on the
Allwinner F1C100s, T113-s3 SPI boot support, and some SPL cleanup
patches.
The branch passed the gitlab CI run, and brief boot testing on some
boards didn't turn up any issues.
In clock_sun9i.c, responsible for (mostly early) clock setup on the
Allwinner A80 SoC, many functions are only needed by the SPL, and are
thus already guarded by CONFIG_SPL_BUILD.
Over the years drivers like for the UART or I2C were converted to DM, and
they care about clock setup themselves now, by using a proper DM clock
driver.
This means those devices need the clock setup functions here for the SPL
only. Move some functions around, to group all SPL-only function within
one #ifdef guard. Some functions were exported, but never used outside
of this file, so remove their prototypes from the header file and mark
them as static.
This avoids unnecessary code in U-Boot proper and helps further
refactoring. Add some comments on the way to help understanding of the
file.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Some later 32-bit SoCs require some setup of the Secure Peripherals
Controller, which is handled in tzpc_init().
At the moment this is guarded in board.c by some #ifdefs selecting the
SoCs that need it.
Move those #ifdef guards into the header file, providing an empty stub
function for all other SoCs, so that the #ifdefs can be removed from the
.c file, to improve readability.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Existing Tegra DSI driver mostly fits T114 apart MIPI calibration
which on T114 has dedicated driver. To resolve this MIPI calibration
logic was split for pre-T114 and T114+ devices.
Tested-by: Ion Agorria <ion@agorria.com> # HTC One X
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Nvidia Tegratab T114
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Consolidate HD headers and place the result into video/tegra20
since it is used only by devices from this directory.
Tested-by: Agneli <poczt@protonmail.ch> # Toshiba AC100 T20
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS Grouper E1565
Tested-by: Ion Agorria <ion@agorria.com> # HTC One X
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Nvidia Tegratab T114
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Diverge DC driver setup to better fit each of supported generations
of Tegra SOC.
Tested-by: Agneli <poczt@protonmail.ch> # Toshiba AC100 T20
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS Grouper E1565
Tested-by: Ion Agorria <ion@agorria.com> # HTC One X
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Nvidia Tegratab T114
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
This message is used to commit into the fuses any new SRK revocation and
FW version information that have been found into the NXP (ELE FW) and
OEM containers.
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Arm's GIC-600 features a Power Register (GICR_PWRR),
which needs to be programmed to enable redistributor
operation. Power on the redistributor and wait until
the power on state is reflected by checking the bit
GICR_PWRR.RDPD == 0. While running U-Boot in EL3
without enabling this register, GICR_WAKER.ChildrenAsleep
bit is not getting cleared and loops infinitely.
This register(GICR_PWRR) must be programmed to mark the frame
as powered on, before accessing other registers in the frame.
Rest of initialization sequence remains the same.
ARM GIC-600 IP complies with ARM GICv3 architecture.
Enable this config if GIC-600 IP present.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Please pull the updates for rockchip platform:
- Add board: rk3588 Generic, Cool Pi CM5, Theobroma-Systems RK3588 Jaguar SBC,
Toybrick TB-RK3588X;
rk3588s Cool Pi 4B;
rk3566 Pine64 PineTab2;
- Add saradc v2 support;
- Add PMIC RK806 support;
- rk3588 disable force_jtag by default;
- Migrate to use IO-domain driver for all boards;
- Use common bss and stack addresses for rk33xx and rk35xx boards;
- Other updates for driver, config and dts;
This architecture and related board are unmaintained currently and have
been for a long time. Remove them.
Signed-off-by: Tom Rini <trini@konsulko.com>
The different macros use writel which is defined in asm/io.h, so let's
include the header so users of hardware.h do not need to include
asm/io.h as well.
While at it, remove asm/io.h includes wherever
asm/arch-rockchip/hardware.h is included already.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
It's one thing to have the register mapped via a well-defined struct but
it's another to be able to make use of it. For that to happen, one needs
to cast the physical address memory of the beginning of the register
address space with the struct. Since this cannot change, let's hardcode
it in the include files so that users do not need to duplicate this line
of code in their own implementation.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Rockchip SoCs can automatically switch between jtag and sdmmc based on
the following rules:
- all the SDMMC pins including SDMMC_DET set as SDMMC function in GRF,
- force_jtag bit in GRF is 1,
- SDMMC_DET is low (no card detected),
Note that the BootROM may mux all SDMMC pins in their SDMMC function or
not, depending on the boot medium that were tried.
Because SDMMC_DET pin is not guaranteed to be used as an SD card card
detect pin, it could be low at boot or even switch at runtime, which
would enable the jtag function and render the SD card unusable.
This is the case for RK3588 Jaguar for example which has an SD card
connector without an SD card card detect signal and has SDMMC_DET
connected to ground.
Because enabling JTAG at runtime could be a security issue and also to
make sure that we have a consistent behavior on all boards by default,
let's disable this force_jtag feature.
However, let's make it easy to reenable it for debugging purposes by
hiding it behind a Kconfig symbol.
Note that soc_con[0] is reserved. But considering that it's way more
user-friendly to access soc_con1 from the TRM with soc_con[1] than
soc_con[0], and that soc_con0 would actually be located at 4 bytes
before soc_con1, let's just make soc_con0 part of the soc_con array.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The functions aren't used anywhere else than in board.c, therefore,
let's not expose them anymore at all.
This merges misc.c and board.c together and removes the functions from
the misc.h header file.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
mctl_mem_matches and mctl_mem_matches_base identical functions. To
avoid code duplication move them to dram_helpers and make
mctl_mem_matches use generic mctl_mem_matches_base.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
The cpu_sun9i.h header file defined the base addresses for quite some
peripherals of the Allwinner A80 CPU, even though we now only use a
fraction of that.
Most of the addresses are now either read from the DT, or were never
used in U-Boot in the first place.
Removed the ones that are not used in the whole of the U-Boot source.
to make it clear that this file only contains addresses that are needed
for the SPL operation.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The cpu_sun4i.h header file defined the base addresses for quite some
peripherals of earlier Allwinner CPUs, even though we now only use a
fraction of that.
Most of the addresses are now either read from the DT, or were never
used in U-Boot in the first place.
Removed the ones that are not used in the whole of the U-Boot source.
to make it clear that this file only contains addresses that are needed
for the SPL operation.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The cpu_sun50i_h6.h header file defined the base addresses for quite some
peripherals of the Allwinner H6 and related CPUs, even though we now only
use a fraction of that.
Most of the addresses are now either read from the DT, or were never used
in U-Boot in the first place.
Removed the ones that are not used in the whole of the U-Boot source.
to make it clear that this file only contains addresses that are needed
for the SPL operation.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The commit fd6e425be2 ("rockchip: rk3588-rock-5b: Enable boot from SPI
NOR flash") added a new BROM_BOOTSOURCE_SPINOR_RK3588 with value 6.
At the time the reason for this new bootsource id value 6 was unknown.
We now know that the BootRom on RK3588 use different bootsource id
values depending on the iomux used by the flash spi controller, and not
by the type of spi nor or spi nand flash used.
Add the following enum values and use them for RK3588 boot_devices.
- BROM_BOOTSOURCE_FSPI_M0 = 3
- BROM_BOOTSOURCE_FSPI_M1 = 4
- BROM_BOOTSOURCE_FSPI_M2 = 6
Fixes: fd6e425be2 ("rockchip: rk3588-rock-5b: Enable boot from SPI NOR flash")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Slawomir Stepien <sst@poczta.fm>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
