When a successful neighbor advertisement is received, the ethernet
address should be saved for later use to avoid having to redo the
neighbor discovery process.
For example, with TFTP the address should get saved into
"net_server_ethaddr". This is being done correctly with ARP for IPv4,
but not for neighbor discovery with IPv6.
Signed-off-by: Sean Edmond <seanedmond@microsoft.com>
Reviewed-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
timeout_count is never reset once a tftpput transfer has started. If for
whatever reason timeouts occur frequently, but the server keeps replying
nonetheless, the transfer may be needlessly aborted.
Reset timer_count on reception of an ACK to avoid this situation.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Linux DTS compatible MDIO bitbanging driver.
Both clause 22 and clause 45 MDIO supported and validated.
Heavily based on the Linux drivers (more or less the same code base).
Signed-off-by: Markus Gothe <markus.gothe@genexis.eu>
This reverts commit 431be621c6.
Section 3.3 of Reduced Gigabit Media Independent Interface (RGMII)
Version 2.0 (4/1/2002) details that a PHYs using a ~2ns internal delay
are referred to as RGMII-ID. This internal delay is optional.
Page 147-148 of the Marvell Doc. No. MV-S107146-U0 Rev. F details
timings of the RX/TX delays. We see that with the TX/RX_CLK delay
enabled, our RX/TX_CTL signal is shifted w.r.t CLK to reflect the delay
added.
In 431be62 there is no timing difference between RGMII and RGMII-ID, and
so programmers wanting to explicitly set their PHY to RGMII will find
that delay added anyway. This could throw off timing if that internal
delay is undesired.
We should be handling all 4 possible RGMII cases of PHY_INTERFACE_MODE:
RGMII, RGMII_ID, RGMII_TXID, and RGMII_RXID. Reverting 431be62
implements this.
See also m88e1111_config_init_rgmii_delays in the equivalent driver in
Linux (drivers/net/phy/marvell.c), which does not set these delays in
RGMII mode.
68e6eca was tested out on an 88E1512 PHY in RGMII-ID mode. This
reversion has been tested by myself on an 88E1518 in RGMII-ID mode. This
patch affects boards using this driver in "rgmii" mode, as the internal
delay will no longer be enabled. Namely kikwood-nsa310s.
Signed-off-by: Rufus Segar <rhs@riseup.net>
We have a some boards that rarely starts networking abnormally, so there are
many timeouts during file transfer. In the same time there is a normal transfer
between timeouts. In this case we can continue transfer (instead of connection
aborting) by just clearing timeout counter on every successful block.
This patch does not affect the case when several timeouts happen one after
another. The transfer will be aborted. Thus the transfer will be
continued in the case of unstable link, but will be aborted in the case
of inaccessible server.
Feature downside: it may greatly slowdown (instead of abort) file transfer
in the case of unstable link.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
When converting a U-Boot trace records file to ftrace function graph
format for use by trace-cmd ('proftool -f funcgraph dump-ftrace'), the
time associated to each function is incorrectly saved in microseconds
instead of nanoseconds. Multuply the value by 1000 to fix the issue.
With this change, the trace-cmd output looks consistent. Here is an
example with udelay(25) added to mem_malloc_init() as a test case:
$ ./tools/proftool -m System.map -t /tmp/trace.bin -f funcgraph \
dump-ftrace -o /tmp/trace.dat
$ trace-cmd report /tmp/trace.dat >/tmp/trace.log
$ vi /tmp/trace.log
[...]
u-boot-1 [000] 6.719659: funcgraph_entry: | mem_malloc_init() {
u-boot-1 [000] 6.719659: funcgraph_entry: | udelay() {
u-boot-1 [000] 6.719660: funcgraph_entry: | schedule() {
u-boot-1 [000] 6.719660: funcgraph_entry: | cyclic_run() {
u-boot-1 [000] 6.719660: funcgraph_entry: 1.000 us | cyclic_get_list();
u-boot-1 [000] 6.719661: funcgraph_exit: 1.000 us | }
u-boot-1 [000] 6.719661: funcgraph_exit: 1.000 us | }
u-boot-1 [000] 6.719661: funcgraph_entry: | __udelay() {
u-boot-1 [000] 6.719662: funcgraph_entry: 0.000 us | usec_to_tick();
u-boot-1 [000] 6.719687: funcgraph_exit: + 26.000 us | }
u-boot-1 [000] 6.719687: funcgraph_exit: + 28.000 us | }
u-boot-1 [000] 6.719687: funcgraph_entry: # 37971.000 us | memset();
u-boot-1 [000] 6.757658: funcgraph_exit: # 37999.000 us | }
u-boot-1 [000] 6.757658: funcgraph_exit: # 38000.000 us | }
In the above dump, the udelay() call is reported as taking 26 us which
is consistent with the timestamps (6.719687 - 6.719659 = 0.000026).
Without this patch we would have "0.026 us" instead of "+ 26.000 us".
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Move to using OF_UPSTREAM config and thus using the devicetree
subtree and remove unused device tree files.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Currently the driver relies on bootph flag to probe it during PRE_RELOC
stage but with the upcoming cleanup of v6.13, we don't have the bootph
property in the parent nodes anymore and ti_sci driver being one of the
parent nodes required during SPL stage would end up hampering the probe
model [0].
Add DM_FLAG_PRE_RELOC to ti_sci driver for mitigating this issue.
[0]: https://source.denx.de/u-boot/custodians/u-boot-dm/-/issues/21
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
The Texas Instruments Foundational Security (TIFS) firmware must match
the security level configured on the SoC. To boot Security Enforced (SE)
variants of the AM62Px, add another tiboot3 build which packages the
Security Enforced (SE) firmware variant for AM62Px SoCs.
Signed-off-by: Bryan Brattlof <bb@ti.com>
OSPI Boot requires overrides specific to R5 and also
to use DMA in R5 SPL stage the DM_TIFS needs to be used.
Add the corresponding overrides for R5 SPL stage.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Prasanth Babu Mantena <p-mantena@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
The wget command currently cannot work correctly with mtk_eth driver.
This patch fixed this by increase DMA ring size and invalidate ring data
after use.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Enable GDMA cpu bridge only when 10Gb interface is enabled for GMAC other
than GMAC0, or when MT7988 internal switch is used.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Not all platforms supports sgmii and/or usxgmii. So we add Kconfig
options for these features and enable them only for supported
platforms.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
MT7629 need extra setting for gmac2 to work. So additional
capability is added for mt7629 to handle this case.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Unlike other platforms, mt7622 has only one SGMII and it can be
attached to either gmac1 or gmac2. So the register field of the
sgmii selection differs from other platforms as newer platforms can
control each sgmii individually.
This patch adds a new capability for mt7622 to handle this case.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The register field for SGMII speed selection is a 2-bit field with
value 0 for 1Gbps and 1 for 2.5Gbps (2/3 are reserved).
So it's necessary to set both bits instead of just setting/clearing
only the lower bit.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
According to the mt7629 programming guide, the CLK_TOP_F10M_REF_SEL
shares the same parent selection with CLK_TOP_IRRX_SEL, while the
present parent selection for CLK_TOP_F10M_REF_SEL is actually used
for CLK_TOP_SGMII_REF_1_SEL.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Andrew Goodbody <andrew.goodbody@linaro.org> says:
Picking up a series from Dan Carpenter and applying requested
changes for v2.
I had previously set CONFIG_64BIT for arm64. This patchset does the
same thing for sandbox and x86_64. (Mips and riscv were already
doing it). This CONFIG option is used in the Makefile to determine
if it's a 32 or 64 bit system for the CHECKER.
Makefile
1052 # the checker needs the correct machine size
1053 CHECKFLAGS += $(if $(CONFIG_64BIT),-m64,-m32)
Link: https://lore.kernel.org/r/20241216180736.1933807-1-andrew.goodbody@linaro.org
Should use CONFIG_64BIT to detect a 64 bit compile and not
CONFIG_PHYS_64BIT. This allows more platforms to run the
full test code.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Select CONFIG_64BIT so that we pass the -m64 option (instead of -m32) to
static analysis tools.
Introduce CONFIG_SPL_64BIT and select it for architectures other than
x86 with 64 bit builds. Do not select it for x86 builds as x86 uses
a 32 bit SPL.
Ensure that when limits are set they use CONFIG_64BIT for U-Boot
proper and CONFIG_SPL_64BIT for SPL. This is to allow for the 32 bit
SPL build used by x86.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In include/linux/io.h the declarations of ioread64 and iowrite64
which make use of readq/writeq are guarded with CONFIG_64BIT so
guard the sandbox declarations of readq and writeq also with
CONFIG_64BIT.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Patch keeps the access to dtb_dt_embedded() within fdtdec API,
by means of new API function introduction. This new function is a
common place for updating appropriate global_data fields for
OF_EMBED case.
Also, the consequence of the patch is movement of '___dtb_dt_*begin'
symbols' declaration from header file, because nobody used symbols
outside the lib/fdtdec.c.
Signed-off-by: Evgeny Bachinin <EABachinin@salutedevices.com>
Suggested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
RFLOW config related MMR does not exist incase of BCDMA.
Add check to bypass the RFLOW MMR extraction.
Without this, the probe sequence fails checking for
the MMR_RFLOW region, which is valid only for packet based
DMA and obselete for BCDMA.
Fixes: 5abb694d60 ("dma: ti: k3-udma: Add support for native configuration of chan/flow")
Signed-off-by: Prasanth Babu Mantena <p-mantena@ti.com>
Tested-by: Jonathan Humphreys <j-humphreys@ti.com>
In commit 399f739be6 ("CI: allow jobs to be run in merge requests") we
added "rules:when: always" to many stages of the pipeline to allow for merge
requests to trigger a run. However based on current Gitlab
documentation, we should still be triggered on merge requests without
this. Furthermore the way we have things written today we always run all
stages of the CI rather than failing out early on problems, which is not
always useful. Remove these as we should still be fine with merge
requests triggering a run.
Link: https://docs.gitlab.com/ee/ci/yaml/#rules
Signed-off-by: Tom Rini <trini@konsulko.com>
Our Gitlab pipeline is currently broken up in to several stages. This
was done with the thought process of "we should test tools and if
they're good test emulated targets and if they're good test real
hardware and if they're good test the world". However, in terms of that
first stage it only really matters that binman, et al are still
functional. And for a few years now Gitlab has had a "needs" keyword
that lets you refine pipeline dependencies. Use this to perform the
minor optimization of having test.py only require that tool testing job.
This will become more useful later when we add long running testsuites
that we do not want to block later jobs.
Signed-off-by: Tom Rini <trini@konsulko.com>
It is annoying to have sandbox enter a boot loop when an assertion
fails. Hang instead, since then the error message is only printed once
and Ctrl-C can be used to quit, as per normal.
Signed-off-by: Simon Glass <sjg@chromium.org>
The mpc8xxx_gpio driver contains a workaround for certain chips
where the previously written state of outputs cannot be read back
from the GPIO data (GPDAT) register (MPC8572/MPC8536). This workaround
consists of tracking the state of GPDAT in a "shadow register" (i.e. a
software variable). The shadow register is initialized to zero.
This results in a problem w.r.t. outputs that are configured to a
high (1) state before U-Boot runs, but not touched by U-Boot itself:
Due to the zero-initialization, these GPIOs end up being set to zero,
the first time that any other output is set.
To avoid such issues initialize the GPDAT shadow register to the value
previously held by any outputs, if possible. On MPC8572/MPC8536 this
should make no difference, i.e. the shadow register should be
initialized to zero on these chips.
This patch has been tested on a MPC8314E-based board.
Reviewed-by: Sinan Akman <sinan@writeme.com>
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
To increase readability, use the defined constant instead of specifying
SPCR[TBEN] as a number.
Reviewed-by: Sinan Akman <sinan@writeme.com>
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
Globals defined in headers can result in multiple-definition errors
while linking, if they are visible beyond the current translation unit.
This hasn't been a problem for initreg.h so far, but would become a
problem in the next patch, where I use a constant from initreg.h in a
second C file.
Reviewed-by: Sinan Akman <sinan@writeme.com>
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
