The driver used for the Allwinner I2C IP is using proper DT and DM
enablement for a while: we enable the clock gate and de-assert the reset
line in the driver's probe() routine, and the pinmux setup is taken care
of by the DM framework.
This means the explicit call to the i2c_init_board() routine is not
needed for U-Boot proper. As the board_init() function in board.c is
only called for U-Boot proper, we can remove the call, something that
the comment there hinted at already.
Fix the comment for the board_init() function on the way: we were not
really doing board specific setup there. The fact that this function
is called from U-Boot proper only is probably more helpful for reasoning
about this code.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Some later 32-bit SoCs require some setup of the Secure Peripherals
Controller, which is handled in tzpc_init().
At the moment this is guarded in board.c by some #ifdefs selecting the
SoCs that need it.
Move those #ifdef guards into the header file, providing an empty stub
function for all other SoCs, so that the #ifdefs can be removed from the
.c file, to improve readability.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The Allwinner F1C100s SoC has a MUSB controller like the one in the A33,
but needs an SRAM region to be claimed like the A10. We do the latter
anyway, even on chips that don't need it, so there is no real difference
in our compatible string matching.
Add a mapping between the config struct used in the Linux to our
requirements here on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
R528/T113 SoCs uses the same SPI IP as the H6, also have the same clocks
and reset bits layout, but the CCU base is different. Another difference
is that the new SoCs do not have a clock divider inside. Instead of this
we should configure sample mode depending on input clock rate.
The pin assignment is also different: the H6 uses PC0, the R528/T113 PC4
instead. This makes for a change in spi0_pinmux_setup() routine.
This patch extends the H6/H616 #ifdef guards to also cover the R528/T113,
using the shared CONFIG_SUNXI_GEN_NCAT2 and CONFIG_MACH_SUN8I_R528
symbols. Also use CONFIG_SUNXI_GEN_NCAT2 symbol for the Kconfig
dependency.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Tested-by: Sam Edwards <CFSworks@gmail.com>
CI: https://source.denx.de/u-boot/custodians/u-boot-video/-/pipelines/20466
- simple_panel: support timing parsing from EDID
- dw_hdmi: fix gcc-14 compiler warnings
- dw_hdmi: support vendor PHY for HDMI
- rockchip: add Rockchip INNO HDMI PHY driver
- rockchip: RK3328 HDMI and VOP support
- evb-rk3328: enable vidconsole support
- Tegra DC and DSI improvements and Tegra 114 support
- add LG LG070WX3 MIPI DSI panel driver
- add Samsung LTL106HL02 MIPI DSI panel driver
- add Toshiba TC358768 RGB to DSI bridge support
- add basic support for the Parade DP501 transmitter
- Tegra 3 panel and bridge driver improvements
- simplefb: modernise DT parsing
- fdt_simplefb: Enumerate framebuffer info from video handoff
- preserve framebuffer if SPL is passing video hand-off
- fdt_support: allow reserving FB region without simplefb
Create separate helper for just reserving framebuffer region without
creating or enabling simple-framebuffer node.
This is useful for scenarios where user want to preserve the bootloader
splash screen till OS boots up and display server gets started without
displaying anything else in between and thus not requiring
simple-framebuffer.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
If SPL is passing video handoff structure to U-boot then it is safe to
assume that SPL has already enabled video and that's why it is passing
video handoff structure to U-boot so that U-boot can preserve the
framebuffer.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
Enable and update simple-framebuffer node using the video handoff
bloblist if video was enabled at SPL stage and corresponding video
bloblist was received at u-boot proper with necessary parameters.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
simplefb was using old style FDT parsing which doesn't behave well in
combination with livetree. Update it to use ofnode instead and add a
missing null check for the "format" property.
Standardise the error logging while we're here.
Fixes: 971d7e6424 ("video: simplefb")
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The Parade DP501 is a DP & DVI/HDMI dual-mode transmitter. It
enables an RGB/Parallel SOC output to be converted, packed and
serialized into either DP or TMDS output device. Only DisplayPort
functionality of this transmitter has been implemented and tested.
Signed-off-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Add initial support for the Toshiba TC358768 RGB to DSI bridge.
The driver is based on the mainline Linux Toshiba TC358768
bridge driver and implements the same set of features.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF700T
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
LTL106HL02 is a color active matrix TFT (Thin Film Transistor)
liquid crystal display (LCD) that uses amorphous silicon TFT as
switching devices. This model is composed of a TFT LCD panel, a
driver circuit and a backlight unit. The resolution of a 10.6"
contains 1920 x 1080 pixels and can display up to 16,8M color
with wide viewing angle.
Co-developed-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Signed-off-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Co-developed-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Anton Bambura <jenneron@protonmail.com>
The LD070WX3 is a Color Active Matrix Liquid Crystal Display with
an integral Light Emitting Diode (LED) backlight system. The
matrix employs a-Si Thin Film Transistor as the active element. It
is a transmissive type display operating in the normally Black
mode. This TFT-LCD has 7.0 inches diagonally measured active
display area with WXGA resolution (800 by 1280 pixel array).
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
According to Thierry Reding's commit in the linux kernel
976cebc35bed0456a42bf96073a26f251d23b264
"drm/tegra: dsi: Make FIFO depths host parameters"
correct depth of the video FIFO is 1920 *words* no *bytes*
Tested-by: Ion Agorria <ion@agorria.com> # HTC One X
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Nvidia Tegratab T114
Signed-off-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Implement reset use to discard any changes which could have been
applied to DSI before and can interfere with current configuration.
Tested-by: Ion Agorria <ion@agorria.com> # HTC One X
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Nvidia Tegratab T114
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Existing Tegra DSI driver mostly fits T114 apart MIPI calibration
which on T114 has dedicated driver. To resolve this MIPI calibration
logic was split for pre-T114 and T114+ devices.
Tested-by: Ion Agorria <ion@agorria.com> # HTC One X
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Nvidia Tegratab T114
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Dedicated MIPI calibration driver is used on T114 and newer. Before
T114 MIPI calibration registers were part of VI and CSI.
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Nvidia Tegratab T114
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
The goal of panel_set_backlight() is to enable backlight. Hence,
it should be called at the probe end.
Signed-off-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
If DISP1 is a PLLD/D2 child, it cannot go over 370MHz. The cause
of this is not quite clear. This can be overcomed by further
halving the PLLD/D2 if the target parent rate is over 800MHz.
This way DISP1 and DSI clocks will have the same frequency. The
shift divider in this case has to be calculated from the
original PLLD/D2 frequency and is passed from the DSI driver.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS Grouper E1565
Tested-by: Ion Agorria <ion@agorria.com> # HTC One X
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Nvidia Tegratab T114
Tested-by: Jonas Schwöbel <jonasschwoebel@yahoo.de> # Microsoft Surface 2
Signed-off-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Add powergate use on T114 to complete resetting of DC.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
T30+ SOC have second PLLD - PLLD2 which can be actively used by
DC and act as main DISP1/2 clock parent.
Tested-by: Agneli <poczt@protonmail.ch> # Toshiba AC100 T20
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS Grouper E1565
Tested-by: Ion Agorria <ion@agorria.com> # HTC One X
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Nvidia Tegratab T114
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tegra SoC has 2 independent display controllers called DC_A and
DC_B, they are handled differently by internal video devices like
DSI and HDMI controllers so it is important for last to know
which display controller is used to properly set up registers.
To achieve this, a pipe field was added to pdata to pass display
controller id to internal Tegra SoC devices.
Tested-by: Agneli <poczt@protonmail.ch> # Toshiba AC100 T20
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS Grouper E1565
Tested-by: Ion Agorria <ion@agorria.com> # HTC One X
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Nvidia Tegratab T114
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Consolidate HD headers and place the result into video/tegra20
since it is used only by devices from this directory.
Tested-by: Agneli <poczt@protonmail.ch> # Toshiba AC100 T20
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS Grouper E1565
Tested-by: Ion Agorria <ion@agorria.com> # HTC One X
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Nvidia Tegratab T114
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Subtracting 1 from x and y fixes image shifting on rotated
panels.
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS Grouper E1565
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Diverge DC driver setup to better fit each of supported generations
of Tegra SOC.
Tested-by: Agneli <poczt@protonmail.ch> # Toshiba AC100 T20
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS Grouper E1565
Tested-by: Ion Agorria <ion@agorria.com> # HTC One X
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Nvidia Tegratab T114
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
GCC-14 find more warnings like
"make pointer from integer without a cast"
fix them by adding a type cast.
Signed-off-by: Khem Raj <raj.khem@gmail.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Model: Firefly roc-rk3328-cc
DRAM: 1 GiB (effective 1022 MiB)
Video device 'vop@ff370000' cannot allocate frame buffer memory -ensure the device is set up before relocation
Error binding driver 'rockchip_rk3328_vop': -28
Some drivers failed to bind
initcall sequence 000000003ffcd5e8 failed at call 000000000021a5c4 (err=-28)
### ERROR ### Please RESET the board ###
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Unlike RK3399, RK3288 the Newer Rockchip SoC's like RK3328 have
different offsets for dsp registers.
Group the dsp register set via dsp_regs pointers so that dsp_offset
would point the dsp_regs to access for any changes in the offset value.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Unlike RK3399, RK3288 the Newer Rockchip SoC's like RK3328 have
different offsets for win registers.
Group the win register set via win_regs pointers so that win_offset
would point the win_regs to access for any changes in the offset value.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Get the regs from priv pointer instead of passing it an argument.
This would simplify the code and better readability.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
HPD detection on some DW HDMI designed SoC's would need to read and
setup the HPD status explicitly.
So, extend the HPD detection code by adding the dw_hdmi_detect_hpd
function and move the default detection code caller there.
The new read and setup hdp will integrate the same function in
later patches.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
DW HDMI support Vendor PHY like Rockchip RK3328 Inno HDMI PHY.
Extend the vendor phy handling by adding platform phy hooks.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
