PLL frequency would overshoot from the original target in
synchronous mode during low VCC voltage condition.
To resolve this issue, PLL is set to run on asynchronous mode
instead of enabling synchronous mode in the clock driver.
Signed-off-by: Muhammad Hazim Izzat Zamri <muhammad.hazim.izzat.zamri@altera.com>
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Some customers prefer to minimize the use of external oscillators,
especially when using the FPGA first configuration mode.
By enabling the configuration of the HPS internal oscillator as
the boot_clk source instead of the default external oscillator,
(HPS_OSC_CLK) in non-secure boot scenarios, this allows them
to eliminate the need for an additional oscillator device and
a dedicated HPS pin, simplifying board layout and routing.
Signed-off-by: Tingting Meng <tingting.meng@altera.com>
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Agilex5 retrieves its clock manager address via probing its own clock
driver model during SPL initialization.
Therefore, excluding Agilex5 from calling generic clock driver in misc
driver.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Initial creation of new system manager driver.
Add supports for the SOCFPGA System Manager Register block which
aggregates different peripheral function into one area.
On 64 bit ARM parts, the system manager only can be accessed during
EL3 mode, this driver model provide user the high level access
to system register and abstract user from low level access.
The base address of system manager can be retrieved
using DT framework through the System Manager driver.
Signed-off-by: Tien Fong Chee <tien.fong.chee@altera.com>
Signed-off-by: Boon Khai Ng <boon.khai.ng@altera.com>
For eMMC v4 and newer that is smaller than 2 GiB, the JEDEC JESD84-B51
section 6.2.4 Configure partitions indicates that EXT_CSD SEC_COUNT
should not be used to determine device size, and instead device size
should be calculated from C_SIZE and C_SIZE_MULT.
This is not exactly accurate, the 2 GiB limit is not a hard line,
there are eMMC devices which are smaller than 2 GiB and still
require device size to be determined from EXT_CSD SEC_COUNT. The
hard line is instead OCR HCS bit, which indicates whether the device
is byte or sector addressed, the former applies to most devices
below 2 GiB, and the later applies mostly to devices above 2 GiB.
However, there are a couple of devices which are smaller than 2 GiB
and still set the OCR HCS bit to indicate they are sector addressed,
and therefore the size calculation for those devices should also
use EXT_CSD SEC_COUNT . Use mmc->high_capacity flag to discern the
devices instead of arbitrary 2 GiB limit. The mmc->high_capacity flag
reflects the OCR HCS bit state.
Fixes: 639b7827d1 ("mmc: fix the condition for MMC version 4")
Signed-off-by: Marek Vasut <marex@denx.de>
This reverts commit c8750efe02, reversing
changes made to 8c6cf8aeea.
Unfortunately these changes do not build on macOS hosts.
Signed-off-by: Tom Rini <trini@konsulko.com>
The length of buffers used to read inode tables, directory tables, and
reading a file are calculated as: number of blocks * block size, and
such plain multiplication is prone to overflowing (thus unsafe).
Replace it by __builtin_mul_overflow, i.e. safe math.
Signed-off-by: Joao Marcos Costa <joaomarcos.costa@bootlin.com>
Branch contains bringup of Acer Iconia Tab A500 (codename picasso), a
Tegra 2 Android device with decent Linux kernel support. Ondevice tests
and U-Boot test suit all passed.
Recent versions of this module call time.perf_counter() so add a patch
for this also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Tom Rini <trini@konsulko.com>
This merges a set of patches from myself and Simon Glass to resolve
various problems that the current version of pylint will report with our
codebase. After the problems are fixed, we update to the now current
version which is 3.3.4.
Memory region used by remote cores was set to non-cached region but
commit 7c9c6e1925 ("arm: mach-k3: Merge initial memory maps") makes
all memory region as cached, unified across K3 devices.
This causes inconsistency while booting remote cores on devices, due to
cache incoherency between remote core and boot code.
So to make this operation coherent, cache the address and len while
loading ELF program headers to memory and flush that region in the next
cycle of load.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Beleswar Padhi <b-padhi@ti.com>
Defining CONFIG_MT8512 is unnecessary as now board for mediatek
target can be changed in config.
Use CONFIG_TARGET_MT8512 to replace CONFIG_MT8512.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Not all MediaTek platforms needs u-boot-mtk.bin.
This patch will let u-boot generates u-boot-mtk.bin only if
CONFIG_MTK_BROM_HEADER_INFO is not empty.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Use preload_check_sign to authenticate the generated image when testing the
preload signature in testPreLoad().
Signed-off-by: Paul HENRYS <paul.henrys_ext@softathome.com>
pre-load related config options are enabled to have support of it in host
tools.
'CONFIG_FIT_SIGNATURE=y' is being automatically removed since it is
selected by CONFIG_IMAGE_PRE_LOAD_SIG.
Signed-off-by: Paul HENRYS <paul.henrys_ext@softathome.com>
preload_check_sign is added so that it can be used to authenticate images
signed with the pre-load signature supported by binman and U-Boot.
It could also be used to test the signature in binman tests signing
images with the pre-load.
Signed-off-by: Paul HENRYS <paul.henrys_ext@softathome.com>
Add an empty inline declaration when compiling tools for a host where
unmap_sysmem() is not defined.
Signed-off-by: Paul HENRYS <paul.henrys_ext@softathome.com>
rsa_verify_openssl() is used in lib/rsa/rsa-verify.c to authenticate data
when building host tools.
Signed-off-by: Paul HENRYS <paul.henrys_ext@softathome.com>
This newer pylint produces errors about variables possibly being used
before being set. Adjust the code to pass these checks.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Tom Rini <trini@konsulko.com>
With a newer pylint, we get a warning that 'br' could be used before
assignment. Fix this by declaring br first as an empty bytearray.
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
With a newer pylint we get a warning about how offset could be used
before assigned. This is because when the underlying filesystem wasn't
one that is supported we would have runtime test failures. Address this
by raise'ing an Exception if fs is not supported.
Signed-off-by: Tom Rini <trini@konsulko.com>
With a newer pylint version we get a warning about how mounted_test_fn
could be used before assignment. Evaluating the code, this can't happen
because we check for "not have_writable_fs_partition" and return before
moving to the part of the tests which use mounted_test_fn. However, we
should instead have this written so that we only try this part of the
test if have_writable_fs_partition is set, and this also fixes the
warning. As part of this we also move test_f and mounted_test_fn to the
section of code that already only does this if
have_writable_fs_partition is set.
Signed-off-by: Tom Rini <trini@konsulko.com>
When running a newer version of pylint it will complain that page_size
may be used before being assignment. Looking deeper what is going on is
that we could run in to the case where the regex we run for any of the
flash information fails but since we don't have a result, we don't check
it either. In the case of the rest of the numerical values we then have
some assignment (multiplying by some value) and so pylint doesn't
complain. Rework things to assert that each regex has a result and so
failure will stop the test and we won't have any use before assignment.
Signed-off-by: Tom Rini <trini@konsulko.com>
As AM57x uses overlays for display and camera interfaces, add support to
load DT overlay files to MMC boot.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
TI AM57x boards use a custom (though family common to TI boards) mechanism
for booting Linux. Add support to enable custom MMC boot as a default
option along with the distroboot approach.
Also, add supporting mmc boot environment variables which shall be used for
custom MMC boot
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
Kernel commit 837833a724 ("environment: ti: Add get_fit_config command
to get FIT config string") introduced "get_fit_config" in ti_armv7_common.h
to mangle the fdtfile name when used to select a config node from the OE
made FIT image. However, the ti_armv7_common.h is common for both K3 and
AM57xx platforms. AM57xx platforms' fdtfile name does not have '/' and
"conf-" prefix so the setexpr command fails and boot hangs.
Override the get_fit_config in AM57x specific config header to get the
correct FIT config name.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
Increase the maximum Image size from 23 MB to 26 MB by moving the
initramfs start address up. This gives us a bigger ranger to
provide kernel images which are not stripped down too much.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Increase the maximum Image size from 23 MB to 26 MB by moving the
initramfs start address up. This gives us a bigger ranger to
provide kernel images which are not stripped down too much.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Enable ENV_IS_IN_SPI_FLASH to read the environment from the SPI
flash when booting from it. The oftree, kernel and ramdisk sizes
are located in this environment and therefore required to boot
an initramfs.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Enable ENV_IS_IN_SPI_FLASH to read the environment from the SPI
flash when booting from it. The oftree, kernel and ramdisk sizes
are located in this environment and therefore required to boot
an initramfs.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
The USB0 instance of USB on AM62 SoC when configured to operate in the
Gadget mode of operation can be used to mount an MMC/SD card on the USB
Host. Hence, enable support for the USB Mass Storage (ums) command.
Since this config fragment corresponds to USB DFU functionality which
configures the USB Controller in Gadget mode of operation, other SoCs
which include this fragment for DFU functionality can make use of the
USB MASS Storage functionality as well.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
The USB0 instance of USB on J722S SoC is a Designware USB Controller with
the same glue layer (wrapper) as AM62 SoC. In order to support USB DFU boot
and USB DFU flash with USB0, enable the corresponding glue layer driver.
While at it, sync with savedefconfig.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
The config fragment "am62x_a53_usbdfu.config" which adds USB DFU support
for AM62x SoC is applicable to the AM62Px SoC as well. Hence, include it
in "am62px_evm_a53_defconfig" in order to enable support for USB DFU
flash and boot. Remove those configs from "am62px_evm_a53_defconfig" which
are present in the "am62x_a53_usbdfu.config" config fragment that is being
included.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Disable configs which are not required for USB DFU functionality, in
order to allow reusing this fragment for AM62Px SoC.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Include the TI K3 DFU environment to support DFU Boot and DFU Flash.
Also add "usb" to the list of "boot_targets". While at it, add a newline
at the end of the file.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
The config fragment "am62x_a53_usbdfu.config" which adds USB DFU support
for AM62x SoC is applicable to the AM62Ax SoC as well. Hence, include it
in "am62ax_evm_a53_defconfig" in order to enable support for USB DFU flash
and boot.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
