define a suitable default address for CONFIG_SPL_LOAD_FIT_ADDRESS
to make it easier on folks enabling HABv4.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The mxc_get_clock function is around for compatibility with older
drivers that are not clock aware. In this case asking for the clk for
MXC_CSPI_CLK does not take into account there are multiple SPI busses on
modern IMX SoC's and it will return the clock for the first bus which
may not be used or configured.
In the case you are not using the first bus you will not get the proper
clock. Fix this by obtaining the clock rate from the bus clock.
This resolves an invalid SPI clock frequency configuration for SPI2 on a
board where SPI1 is not used.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
In case an rswitch port is described as disabled in DT, do not
register it as ethernet device in U-Boot. This way, such ports
cannot be accessed from U-Boot command line.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Move CONFIG_ENV_OVERWRITE=y into commont renesas_rcar.config to make sure
this configuration option is consistently enabled on all of Renesas R-Car
Gen2, Gen3, Gen4. Currently this option is not enabled on Gen4, this fix
corrects that omission.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
First, thanks to Simon Glass and also Linaro, we now have access to a
few fast arm64 host machines in our Gitlab instance, to use as CI
runners. This series finishes the work that I pushed earlier and Simon
had started that enables arm64 hosts to be used for most things now.
The first notable change, especially if you use this on your own Gitlab
instance is that "DEFAULT_TAG" is now unused and we instead have:
- DEFAULT_ALL_TAG:
- DEFAULT_ARM64_TAG:
- DEFAULT_AMD64_TAG:
- DEFAULT_FAST_AMD64_TAG:
This lets us say that some jobs can be run on all runners, because they
are small enough that anything we'd connect to CI is fast enough and it
also does not depend on the underlying host architecture. Next we have
tags for any arm64 host, or any amd64 host. Finally, we have a tag for
fast amd64 hosts. What these last three are for is that we have a few
jobs that need to run on amd64 hosts and so we have to restrict them
there, but we also have now reworked the world build jobs to build
(almost) everything in a single job and on the fast amd64 machines this
is still as quick as the old way was, in practice.
To reach this point, we say that the Xtensa jobs can only run on amd64
hosts. Our targets only work with the binary-only toolchain and so this
is a reasonable limit and we exclude them from the world build jobs. We
also need to deal with ensuring the right toolchain is used regardless
what the host architecture is and that we don't use the host toolchain
by accident. Finally, because some of these changes needed to be worked
out in the linter, fix some of the general warnings that notes as well.
First, try and be slightly clearer about what "buildx" is with respect
to the docker build process.
Second, now that we build the container for both amd64 and arm64, we
should document how to make a docker "builder" that has multiple nodes.
With this one node should be amd64 and one node arm64, and with
reasonably fast arm64 hardware this will be much quicker than using
QEMU.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We should always look in our downloaded toolchains first and then for
host-provided toolchains.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We do not want to use the host toolchain for building our platforms in
CI (it is both too old, and would be inconsistent with our CI
practices). To do this we need to set the toolchain-prefix so that we
don't end up guessing "/opt/.../aarch64-linux-aarch64-linux-" as the
prefix.
Link: https://source.denx.de/u-boot/custodians/u-boot-dm/-/issues/32
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the test.py stage of the build we mark the pytest results as
artifacts to save, so that they can be used for reports. This however
leads to all of the artifacts being downloaded (and then not used) in
later stages. Optimize this out by using an empty list of dependencies
here (which is the keyword for which artifacts are needed).
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When validating our current pipeline, a warning is produced about a lack
of a default workflow. For how we use it, we can add a simple default of
"always".
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
First, introduce DEFAULT_ALL_TAG, DEFAULT_ARM64_TAG, DEFAULT_AMD64_TAG
and DEFAULT_FAST_AMD64_TAG and remove the previous DEFAULT_TAG (as
anyone making use of that will need to adjust their jobs). This allows
us to say that some jobs can run on amd64 or arm64 hosts under the all
tag, while some jobs must run on amd64 (the Xtensa jobs due to
binary-only toolchains and sandbox for now) Then we rework the world
build stage to only run on our very fast amd64 hosts, or our arm64 hosts
(which are also very fast). This should result in a similar overall
build time but also a much more consistent overall build time as we
won't have the two big world jobs possibly run on our slower build
nodes.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove the rest of the places where we hard-code the version of the
toolchain we're using.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The xtensa architecture is interesting in that the platforms we support
are only valid on the binary-only toolchains as the DC233C instruction
set requires those toolchains (and not the FSF instruction set). Only
install the binary toolchain on amd64 hosts and only run the tests on
them as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
TFTP transfers of large files, for example 128 MiB, can sporadically
get stuck and the transfer slows down considerably.
This happens because the TX DMA descriptor in DRAM becomes out of sync
with the view of the TX DMA descriptor content from the CPU side, which
is viewed through the CPU caches. In order to guarantee these two views
are consistent, the cache over TX DMA descriptor that has possibly been
written by the rswitch hardware must first be invalidated, only then can
the descriptor be cleared and updated by the CPU, and finally the cache
over that area must be flushed back into DRAM to make sure the rswitch
hardware has consistent view of the updated descriptor content.
The very first invalidation operation was missing, which led to sporadic
corruption of the TX DMA descriptor. Fix it, add the missing invalidation
operation.
Reported-by: Enric Balletbo i Serra <eballetb@redhat.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Enric Balletbo i Serra <eballetb@redhat.com>
TFTP transfer size can be used to re-size the TFTP progress bar on
single line based on the server reported file size. Enable it by
default for Renesas hardware to avoid long scrolling walls of '#'
character during long TFTP transfers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Early revisions of the R-Car V4M Series Hardware User’s Manual
contained an incorrect formula for the CPU core clocks:
ZCnφ = (PLL2VCO x 1/2) x mult/32
Dang-san fixed this by using CLK_PLL2_DIV2 instead of CLK_PLL2 as the
parent clock.
In Rev.0.70 of the documentation, the formula was corrected to:
ZCnφ = (PLL2VCO x 1/4) x mult/32
As the CPG Block Diagram now shows a separate 1/4 post-divider for PLL2,
the use of CLK_PLL2_DIV2 is a recurring source of confusion. Hence get
rid of CLK_PLL2_DIV2, and include the proper 1/4 post-divider in the
invocation of the DEF_GEN4_Z() macro, like is done on other R-Car Gen4
(and Gen3) SoCs.
Ported from Linux commit
92850bed9d4d ("clk: renesas: r8a779h0: Drop CLK_PLL2_DIV2 to clarify ZCn clocks")
Reported-by: Vinh Nguyen <vinh.nguyen.xz@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/0d2789cac2bf306145fe0bbf269c2da5942bb68f.1728377724.git.geert+renesas@glider.be
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
One can use ccache by keeping ccache in PATH or by providing the full
path to ccache as well. Providing the full path to ccache fails as the
current regex tries to look for ccache being the initial token during
filtering.
Do a greedy search to remove anything before ccache for regex matching.
Fixes: 04b1d84221 ("Makefile: fix empty MK_ARCH when using ccache")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
commit e27bddff4b ("imx8m: Restrict usable memory to space below 4G boundary")
tried to adjust the usable memory limits on a 4GB boundary.
ram_top is described as 'top address of RAM used by U-Boot' and we want
to preserve that. This is defined as a phys_addr_t and unfortunately
its size differs across architectures. This has lead us to a weird
state where 32bit boards define it 'SZ_4GB - 1' and 64bit boards as
'SZ_4GB' unless it was otherwise defined.
With some recent LMB changes and specifically
commit 1a48b0be93 ("lmb: prohibit allocations above ram_top even from same bank")
the board fails to boot properly although the commit above is correct
since it's making sure that no memory above ram_top is usable -- but
added to our memory map so EFI can hand it over to the booted OS.
The reason for that is that during the LMB init we add all usable memory
in lmb_add_memory(). In that function any memory above ram_top gets added
as 'reserved' for LMB. With the current values tha's set to 0xFFFF_FFFF
for this board. Later LMB is trying to protect the memory area U-Boot lives
in with lmb_reserve_common(). The latter fails though since it tries to
add U-Boot top (which is 0xFFFF_FFFF as well) to U-Boot 'bottom'. This call
will fail since 1 byte of that memory range is already marked as 'reserved'.
Since we are close to the release, LMB seems to assume that the address
is rounded up and is the 'next address' and so does parsing and adding
memory ranges from DT files, bump the ram_top of the board by 1byte.
In the long run we should change all of the above and have 32b and 64b
platforms define ram_top identically.
Add a Fixes tag although the commit is correct, so people can figure out
the broken scenarios in the future.
Suggested-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Fixes: commit 1a48b0be93 ("lmb: prohibit allocations above ram_top even from same bank")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reported-by: João Paulo Gonçalves <jpaulo.silvagoncalves@gmail.com>
Closes: https://lore.kernel.org/all/20241216114231.qpfwug3zfqkxn3d5@joaog-nb.corp.toradex.com/
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Fixes: 74f88b7221 ("ARM: imx: imx8m: Fix board_get_usable_ram_top()")
("Enable EFI_LOADER_BOUNCE_BUFFER") is not the correct fix for the
problem it describes.
The change of memory addressing leading to side-effects in commit
22f2c9ed9f ("efi: memory: use the lmb API's for allocating and
freeing memory") is remedied by commit 1a48b0be93 ("lmb: prohibit
allocations above ram_top even from same bank").
This reverts commit 9c792ab336.
eth_get_dev() returns NULL if no network device is available.
Not checking the return value leads to a crash when the device
pointer is dereferenced.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Jerome Forissier <jerome.forissier@linaro.org>
If the dns command cannot find a network interface, we should return
CMD_RETFAIURE and not -1 (CMD_RET_USAGE).
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Jerome Forissier <jerome.forissier@linaro.org>
There have been a few changes to the areas that this file documents
without having regenerated the file. Do so now.
Signed-off-by: Tom Rini <trini@konsulko.com>
When specifying a directory containing DTBs with 'fit,fdt-list-dir', it can be
handy not to have to also specify this directory to the input directories of
binman with '-I' option and use the method tools.append_input_dirs() append it.
This avoids to have to specify the DTB directory in both the device tree
provided to binman and through '-I' option to binman.
Signed-off-by: Paul HENRYS <paul.henrys_ext@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
append_input_dirs() can be used to append a list of input directories to indir
global list.
Signed-off-by: Paul HENRYS <paul.henrys_ext@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change allows to replace both 'SEQ' and 'NAME' keywords by respectively a
sequence number and the name of the FDT to provide more flexibility in the node
name for the device trees included in the FIT.
Signed-off-by: Paul HENRYS <paul.henrys_ext@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Input directories can be passed to binman using the '-I' option and those
input directories are now also passed to 'dtc' when run by binman.
Signed-off-by: Paul HENRYS <paul.henrys_ext@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
An optional list of input directories can be passed to EnsureCompiled() which
allows to pass a list of directories where input files can be searched.
Signed-off-by: Paul HENRYS <paul.henrys_ext@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
mkimage can be used for both signing the FIT or encrypt its content and the
option '-k' can be used to pass a directory where both signing and encryption
keys can be retrieved. Adding 'fit,encrypt' property to the 'fit' node, leads to
try to find keys directory among binman include directories.
_get_priv_keys_dir() is renamed as _get_keys_dir() and adapted to support both
signing and encryption nodes in the FIT.
Signed-off-by: Paul HENRYS <paul.henrys_ext@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When the initialisation vector is randomly generated, its value shall be
stored in the FIT together with the encrypted data. The changes allow to
store the IV in the FIT also in the case where the key is not stored in
the DTB but retrieved somewhere else at runtime.
Signed-off-by: Paul HENRYS <paul.henrys_ext@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For new PowerPC developments, it will be useful to borrow devicetrees
from Linux. This patch makes it possible.
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
In generic_phy_get_bulk(), if 'phys' property is absent in
the device node then it is not an error condition.
Change print message verbosity to debug to avoid spamming
console in such cases.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
The current value of CONFIG_FASTBOOT_BUF_ADDR is incorrect for hardware
with 512MB and 1GB of RAM. The RAM address ranges for these devices are:
- 512MB:
- Start: 0x80000000
- End: 0xA0000000
- 1GB:
- Start: 0x80000000
- End: 0xC0000000
The current buffer address makes fastboot downloads work only on
hardware with 2GB of RAM.
To fix this issue:
1. Lower CONFIG_FASTBOOT_BUF_ADDR to 0x88200000. This makes the buffer
to be equal ot CONFIG_SYS_LOAD_ADDR, which is a safe address to
download files using fastboot.
2. Reduce the size of the download buffer to 128MB, avoiding overlaps
with RAMDISK_ADDR_R. This is a good enough value for individual
downloads.
These changes make fastboot downloads work with 512MB and 1GB devices.
Fixes: defe30a78b ("verdin-am62: add DFU, USB and UUU fastboot support")
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Support of legacy 64-bit entry point was already present when booting a bzimage
with 'zboot' but not supported with 'bootm' when the x86_64 Linux kernel is
embedded in a FIT image.
Signed-off-by: Paul HENRYS <paul.henrys_ext@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Evgeny Bachinin <EABachinin@salutedevices.com> says:
This patch-set repairs ability to use sandbox with CONFIG_OF_EMBED=y.
For now, to use OF_EMBED, the following must be done
1) sandbox64_defconfig should have:
```
-CONFIG_OF_LIVE=y
+CONFIG_OF_EMBED=y
```
2) On sandbox when CONFIG_OF_EMBED=y, the u-boot process can't start
due to:
```
Bloblist at b000 not found (err=-2)
initcall failed at call 000000000011829c (err=-2: No such file or \
directory)
### ERROR ### Please RESET the board ###
```
So, it is natural desire to disable CONFIG_BLOBLIST just to test
sandbox with OF_EMBED=y (disable it one way or another):
```
config SANDBOX
- select BLOBLIST
+ select BLOBLIST if SOME_NON_EXISTING_OPTION
```
3) As a result, having such changes (CONFIG_OF_EMBED=y &&
CONFIG_BLOBLIST=n) leads to the link & run-time errors, being fixed
by this patch series.
Link: https://lore.kernel.org/r/20241202-sandbox_repair_of_embed-v1-0-05aff4b0ccf7@salutedevices.com
[trini: The final patch is dropped as no longer relevant with Simon's
rework to that function which is now applied.]
This series is from Simon Glass <sjg@chromium.org>.
It first corrects the test for checking if a bloblist could have come
from TPL and so we check for a device tree, and then changes the
argument order for board_fdt_blob_setup() to be more inline with our
usual argument ordering.
Link: https://lore.kernel.org/r/20241102174944.412088-1-sjg@chromium.org
Having CONFIG_OF_EMBED=y && CONFIG_BLOBLIST=n leads to the link
error:
```
ld: /tmp/ccwtRVty.ltrans28.ltrans.o:(.data.rel+0x4b0): undefined \
reference to `do_ut_bloblist'
```
Fixes: 6ea5df39e8 ("test: Only enable bloblist test when supported")
Signed-off-by: Evgeny Bachinin <EABachinin@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Having CONFIG_OF_EMBED=y && CONFIG_BLOBLIST=n leads to the link
error:
```
ld: /tmp/ccRVty.ltrans40.ltrans.o: in function `lib_test_is_enabled':
test/lib/kconfig.c:24: undefined reference to \
`invalid_use_of_IF_ENABLED_INT'
ld: test/lib/kconfig.c:26: undefined reference to \
`invalid_use_of_CONFIG_IF_ENABLED_INT'
```
Fixes: 29784d62ed ("test: Add some tests for kconfig.h")
Signed-off-by: Evgeny Bachinin <EABachinin@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Having CONFIG_OF_EMBED=y && CONFIG_BLOBLIST=n leads to the link
error:
```
ld: /tmp/ccwtRVty.ltrans0.ltrans.o: in function `state_uninit':
arch/sandbox/cpu/state.c:508: undefined reference to `bloblist_finish'
```
Fixes: 1c52fcca72 ("sandbox: Write out bloblist when exiting")
Signed-off-by: Evgeny Bachinin <EABachinin@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This returns a devicetree and updates a parameter with an error code.
Swap it, since this fits better with the way U-Boot normally works. It
also (more easily) allows leaving the existing pointer unchanged.
No yaks were harmed in this change, but there is a very small code-size
reduction.
For sifive, the OF_BOARD option must be set for the function to be
called, so there is no point in checking it again. Also OF_SEPARATE is
defined always.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
[trini: Update total_compute]
Signed-off-by: Tom Rini <trini@konsulko.com>
