Introduce a common fdt operations library for basic device tree
operations that are common between various boards.
The first library to introduce here is the capability to set up
fdtfile as a standard variable as part of board identification rather
than depend on scripted ifdeffery.
Reviewed-by: Jonathan Humphreys <j-humphreys@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Add missing board/ti/common/Kconfig references for the platforms that
missed it. The intent is for the common Kconfig to be usable across TI
reference boards as required.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Add Renesas R8A779H0 V4M DT extras for U-Boot.
Until the RPC node becomes part of main DT, keep it here as
an extension so that board code can enable and use the RPC
to access SPI NOR.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Add PLL7 support to Gen3/Gen4 common clock driver. Add initial PLL7
multiplier and divider values into table in R8A779H0 V4M clock driver.
The PLL7 is new PLL added in R8A779H0 V4M SoC. Only integer multiplication
mode is supported by PLL7. The PLL reference clock are either 16.66 MHz or
20 MHz on R8A779H0 V4M SoC, and the output frequency must be 2000 MHz. The
multiplier values fitting this requirement are calculated to 120 or 100.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
These select/imply settings are common to the whole architecture not just
these boards, move these settings to the architecture config.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
TI KS2 boards have the nfs command in their common environment boot
configuration, enable this command.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
- Add USB support for phycore-imx8mp
- Fix environment corruption, reset on mx6sabresd
- Print reset cause on imx8
- Extend mkimage to support generating an image for i.MXRT FlexSPI
- Add new apalis and colibri variants
- Add support for phyBOARD-Segin-i.MX93 support
- Fix when FEC is primarily used instead of EQOS on i.MX93.
add support for Serial Downloader Boot via UUU as well as flashing emmc
via UUU on USB0 Port of phyBOARD Pollux.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
With Ethernet DM in place, there is no longer the need for having
the board_phy_config() anymore.
Remove it.
Confirmed that TFTP transfer still works fine without board_phy_config().
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Fabio Estevam <festevam@denx.de>
U-Boot binary has grown in such a way that it goes beyond the reserved
area for the environment variables.
Running "saveenv" and rebooting the board causes U-Boot to hang because
of this overlap.
Fix this problem by selecting CONFIG_LTO so that the U-Boot proper
size can be reduced.
Also, to prevent this same problem to happen in the future, use
CONFIG_BOARD_SIZE_LIMIT, which can detect the overlap in build-time.
CONFIG_BOARD_SIZE_LIMIT is calculated as follows:
CONFIG_BOARD_SIZE_LIMIT = CONFIG_ENV_OFFSET - u-boot-img.dtb offset
CONFIG_BOARD_SIZE_LIMIT = 0xc000 - 69 * 1024
CONFIG_BOARD_SIZE_LIMIT = 715766
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Commit d5eae216d8 ("net: dwc_eth_qos: Add board_interface_eth_init()
for i.MX93") implemented board_interface_eth_init for i.MX9 platforms.
However it only accounted for the EQOS interface while any board using
FEC as primary Ethernet interface was left out as return value -EINVAL
is always returned from the function in such case.
Fix this by returning 0 (success) when FEC interface is primarily used
instead of EQOS interface on i.MX93.
Fixes: d5eae216d8 ("net: dwc_eth_qos: Add board_interface_eth_init() for i.MX93")
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Tested-by: Mathieu Othacehe <m.othacehe@gmail.com>
Modify imx8m Flex SPI Configuration Block to work with imxrt.
Add more Flex SPI configuration options to Kconfig.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mn-beacon
Linux 6.6.y with KASLR enabled would print the following message on boot:
"
KASLR disabled due to lack of seed
"
Enable the 'kaslrseed' command so a random number seed can be pulled
from CAAM and inserted into the /chosen node 'kaslr-seed' property of
Linux kernel DT before boot, thus letting KASLR work properly.
Signed-off-by: Marek Vasut <marex@denx.de>
When an XXX_BOOTCOMMAND isn't defined, the result is that bootcmd is set
to some random memory content. Fix it so that the function does nothing
in that case and leaves the bootcmd environment unmodified.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Rename nxp_c45_tja11xx structure to nxp_c45_tja1103. The driver will
support more PHYs and nxp_c45_tja11xx is too generic.
Signed-off-by: "Radu Pirea (NXP OSS)" <radu-nicolae.pirea@oss.nxp.com>
Read PHY speed from hardware instead of assuming 100Mbps by default.
The TJA1103 works only at 100Mbps, but the driver will support more PHYs.
Signed-off-by: "Radu Pirea (NXP OSS)" <radu-nicolae.pirea@oss.nxp.com>
Use a local definition for the PHY features. PHY_100BT1_FEATURES are
not defined using the 100BaseT1 bit, so keep this workaround in the driver.
Signed-off-by: "Radu Pirea (NXP OSS)" <radu-nicolae.pirea@oss.nxp.com>
This error path should return -EINVAL instead of success.
Fixes: e261fbf347 ("blk: host_dev: Sanity check on the size of host backing file")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Add a comment to explain the code under is_secure condition of
ti_sci_do_xfer. This will help avoid confusion amongst people who may in
future touch upon this code.
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
The ti_sci driver in U-Boot has support for secure_msg as part of it's
do_xfer function. This let's U-boot send secure messages during boot up.
The protocol to send such secure messages is described as part of the
struct ti_sci_secure_msg_hdr. As part of this, there are 2 fields for
checksum and reserved that occupy the first 4 bytes of any secure
message. This is called as the secure_hdr.
As of now, the secure_hdr needs to be 0 init-ed before sending secure
messages. However the existing code was never putting the zero-inited vars
into the secure_buf, leading to possibility of the first 4 bytes of
secure_buf being possibly garbage.
Fix this by initialising the secure_hdr itself to the secure_buf
location, thus when we make secure_hdr members 0, it automatically ensures
the first 4 bytes of secure_buf are 0.
Fixes: 32cd25128b ("firmware: Add basic support for TI System Control Interface (TI SCI)")
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
The number of DDR controllers to be initialised and used should depend
on the device tree with the constraint of the maximum number of
controllers the device supports. Since J721S2 has multiple (2)
controllers, instead of hardcoding the number of probes, move to
depending on the device tree UCLASS_RAM nodes present.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
