A common device attached to SPI are SPI NAND and some device might
require to have info on the attached NAND to know the flash page size
and spare size.
To support this, introduce setup_for_spinand() that pass the attached
spinand info from manufacturer.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
[trini: Switch to forward declaration of struct spinand_info]
Signed-off-by: Tom Rini <trini@konsulko.com>
Drop unneeded spi.h header include from spinand.h, nothing included by
spi.h is actually used in this header and .c should correctly included
spi.h if actually needed.
Replace spi.h with linux/bitops.h as this is what is actually required
for spinand.h
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Port Linux kernel regmap_set/clear_bits shorthands to set and clear bits
in a regmap. These are handy if only specific bits needs to be applied
or cleared and makes it easier to port regmap based driver from kernel
upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add support for loading the secure & non-secure pdi images and PL
bitstream on the Versal Gen2 platform. The FPGA driver is enabled
to load the bitstream in PDI format on the AMD Versal Gen2 device.
PDI is the new programmable device image format for Versal Gen2,
and the bitstream for the Versal Gen2 platform is generated exclusively
in this format.
With the enhanced SMC format in TF-A ensuring transparent payload
forwarding for Versal Gen2, the u-boot driver must now handle the
word swapping of PDI address that was previously done in TF-A for
this API. The source code for the Versal2 loadpdi command and the
CONFIG_CMD_VERSAL2 configuration has been removed. It now utilizes
the fpga load <dev> <address> <length> command to load secure &
non-secure pdi images.
Signed-off-by: Prasad Kummari <prasad.kummari@amd.com>
Link: https://lore.kernel.org/r/20250327105200.1262615-3-prasad.kummari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for loading the secure & non-secure pdi images and
PL bitstream on the Versal NET platform. The FPGA driver is enabled
to load the bitstream in PDI format on the AMD Versal NET device.
PDI is the new programmable device image format for Versal NET,
and the bitstream for the Versal NET platform is generated exclusively
in this format.
The source code for the versalnet loadpdi command and the
CONFIG_CMD_VERSAL_NET configuration has been removed. It now utilizes
the fpga load <dev> <address> <length> command to load secure &
non-secure pdi images.
Signed-off-by: Prasad Kummari <prasad.kummari@amd.com>
Link: https://lore.kernel.org/r/20250327105200.1262615-2-prasad.kummari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Added extended support for retrieving the PMC muti boot mode
register via the firmware interface, which is preferred when
U-Boot runs in EL2 and cannot directly access PMC registers
via raw reads. Ideally, all secure registers should be accessed
via xilinx_pm_request(). Introduced the secure
zynqmp_pm_get_pmc_multi_boot_reg() call, which uses
xilinx_pm_request() to read the PMC multi boot mode register.
BootROM increments the MultiBoot register (PMC_MULTI_BOOT) read
address offset by 32 KB and retries. For SD and eMMC boot modes,
it can search up to 8191 FAT files for the identification string.
A 13-bit mask (0x1FFF) is applied to PMC_MULTI_BOOT_MASK to obtain
the correct values in BootROM.
Signed-off-by: Prasad Kummari <prasad.kummari@amd.com>
Link: https://lore.kernel.org/r/20250305134845.3182193-1-prasad.kummari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Added extended support for retrieving the boot mode register
via the firmware interface, which is preferred when U-Boot
runs in EL2 and cannot directly access CRP registers via raw
reads. Ideally, all secure registers should be accessed via
xilinx_pm_request(). Introduced the secure zynqmp_pm_get_bootmode_reg()
call, which uses xilinx_pm_request() to read the boot mode register.
When CONFIG_ZYNQMP_FIRMWARE is enabled, the secure
zynqmp_pm_get_bootmode_reg() call is used; otherwise,
direct raw reads are performed in the case of mini U-Boot.
Signed-off-by: Prasad Kummari <prasad.kummari@amd.com>
Link: https://lore.kernel.org/r/20250219115301.3661036-1-prasad.kummari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
On the AM3359 ICE we have two modes of operation CPSW mode or PRU-ICSS
mode.
For PRU-ICSS mode, connect Pin2 and Pin3 of J18 and J19 and for CPSW mode,
connect Pin1 and Pin2 of J18 and J19.
This patch adds support for PRUSS mode boot strapping from uboot.
Co-developed-by: Basharath Hussain Khaja <basharath@couthit.com>
Signed-off-by: Basharath Hussain Khaja <basharath@couthit.com>
Signed-off-by: Parvathi Pudi <parvathi@couthit.com>
When FIT image with multiple dtbs are involved for R5 boot process,
R5 SPL starts off with the first instance of dtb to probe the
eeprom, then once we have identified the type of board, invocation
of setup_multi_dtb_fit will replace the gd->fdt_blob with the proper
board dtb match. However, when we do this, two things happen:
a) Prior to the invocation of setup_multi_dtb_fit, as part of the eeprom
discovery process, i2c controller device is already probed and marked
as exclusive with the match of the very first tisci match (from the
original boot dtb). This list is stored in the info->dev_list of the
first probe.
b) When the second dtb is loaded, tisci is probed again (since this is a
new node) and the new info->dev_list is empty.
At this stage, the exclusive devices such as i2c instances used to
probe the board information is left in the old info->dev_list that is
no longer used actively by the system using the replaced dtb.
As a result of this, the cleanup we intend to do with
ti_sci_cmd_release_exclusive_devices is no longer complete and
leaves the instances such as i2c for eeprom marked used as we scan just
the new info->dev_list.
This creates a problem when Device Manager(DM) firmware starts up later
on in the boot process and identifies that this instance of i2c is
already marked active, so it assumes this can no longer be controlled
by software and is marked internally as reserved and HLOS can no
longer control these instances. This defeated the purpose of
ti_sci_cmd_release_exclusive_devices.
NOTE: This scheme works just fine if the FIT has just a single dtb as
the info->dev_list is upto date.
To fix this, let us make ti_sci_cmd_release_exclusive_devices scan the
all registrations of tisci instances and cleanup all exclusive devices
that have ever been registered.
As part of this, change the prototype of release_exclusive_devices to
drop the handle since that has no further meaning now.
Though this issue was identified on AM64-sk, this can be present in
other builds which use multi-fit-dtb for R5 SPL startup.
Fixes: 9566b777ae ("firmware: ti_sci: Add a command for releasing all exclusive devices")
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Jerome Forissier <jerome.forissier@linaro.org> says:
This series replaces the dynamic initcalls (with function pointers) with
static calls, and gets rid of initcall_run_list(), init_sequence_f,
init_sequence_f_r and init_sequence_r. This makes the code simpler and the
binary slighlty smaller: -2281 bytes/-0.21 % with LTO enabled and -510
bytes/-0.05 % with LTO disabled (xilinx_zynqmp_kria_defconfig).
Execution time doesn't seem to change noticeably. There is no impact on
the SPL.
The inline assembly fixes, although they look unrelated, are triggered
on some platforms with LTO enabled. For example: kirkwood_defconfig.
CI: https://source.denx.de/u-boot/custodians/u-boot-net/-/pipelines/25514
Link: https://lore.kernel.org/r/20250404135038.2134570-1-jerome.forissier@linaro.org
Change board_init_f(), board_init_f_r() and board_init_r() to make
static calls instead of iterating over the init_sequence_f,
init_sequence_f_r and init_sequence_r arrays, respectively. This makes
the code a simpler (and even more so when initcall_run_list() is
later removed) and it reduces the binary size as well. Tested with
xilinx_zynqmp_kria_defconfig; bloat-o-meter results:
- With LTO
add/remove: 106/196 grow/shrink: 10/28 up/down: 31548/-33829 (-2281)
Total: Before=1070471, After=1068190, chg -0.21%
- Without LTO
add/remove: 0/54 grow/shrink: 3/0 up/down: 2322/-2832 (-510)
Total: Before=1121723, After=1121213, chg -0.05%
Execution time does not change in a noticeable way.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
The Tegra Note 7 is a mini tablet computer and the second Tegra 4
based mobile device designed by Nvidia that runs the Android operating
system. The Tegra Note has a 7" IPS display with 1280 x 800 (217 ppi)
resolution. The 1 GB of RAM and 16 GB of internal memory can be
supplemented with a microSDXC card giving up to 64 GB of additional
storage.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The ASUS Transformer Pad TF701T is an Android tablet computer made by
ASUS, successor to the ASUS Transformer Pad Infinity. The tablet includes
a Tegra 4 T114 processor clocked at 1.9 GHz, and an upgraded 2560×1600
pixel resolution screen, increasing the pixel density to 300 PPI and
a mobile dock. Transformers (t114) board derives from Nvidia Macallan
development board.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Most device headers contain SoC specific part and common Tegra post part.
Add a generic header which can be used by any Tegra device of one of the
supported SoC generations (T20, T30, T114, T124 or T210) without need in
device specific configuration.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Link CFG_SYS_NS16550_COM1 value to chosen CONFIG_TEGRA_ENABLE_UART Tegra
wide. Remove all CFG_SYS_NS16550_COM1 from device headers.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The Motorola Atrix 4G (MB860) and Droid X2 (MB870) both featured a
dual-core NVIDIA Tegra 2 AP20H processor clocked at 1GHz, coupled with 1GB
of DDR2 RAM. Storage consisted of 16GB of internal flash memory, expandable
via microSD. The display was a 4.0-inch TFT LCD with a resolution of
960x540 pixels (qHD). The devices originally ran on Android up to 2.3
(Gingerbread).
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The CPCAP is a Motorola/ST-Ericsson creation, a multifunctional IC whose
main purpose was power control. It was used in a wide variety of Motorola
products, both Tegra and OMAP based. The most notable devices using this
PMIC are the Motorola Droid 4, Atrix 4G, and Droid X2.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Qualcomm changes for v2025.07:
CI: https://source.denx.de/u-boot/custodians/u-boot-snapdragon/-/pipelines/25653
There's been a surprising amount of activity lately on the Qualcomm
side with the two oldest boards getting some fresh attention and a lot
of cleanup and polish going on across the board.
* SDM660 gets USB phy fixes and a pinctrl driver
* The recently added SA8775P/QCS9100 SoC gets a pinctrl driver
* The Qualcomm pinctrl driver now handles reserved pins correctly,
fixing crashes on some boards when running "gpio status -a"
* OF_UPSTREAM_BUILD_VENDOR is enabled in qcom_defconfig
* SDM845 and SC7280 get missing clocks added (since we're now stricter
about those). This gets USB working more reliably in more cases.
* DM_USB_GADGET is enabled for all boards using DWC3 and fasbtoot is
enabled too
* A bug in the livetree fixup code is fixed (making USB work on a lot
more platforms)
* Button label lookup is made case insensitive* bootretry becomes more dynamic, allowing it to be hijacked to make a
"persistent" boot menu that allows dropping to U-Boot shell later on
* A new qcom-phone.config fragment is added along with a phone-specific
default environment and phone-specific debugging/bringup docs. These
make U-Boot more usable on devices without a serial port or keyboard.
* The db820c gets fixed up and updated documentation
* The db410c also gets some love and modernisation as well as a new
reviewer.
* A new driver is added for the USB VBUS regulator found on various
Qualcomm PMICs
* The Qualcomm SPMI driver gets some fixes and cleanup for SPMI v5 and
v7 support.
Pull request efi-2025-07-rc1
CI:
* https://source.denx.de/u-boot/custodians/u-boot-efi/-/pipelines/25648
Documentation:
* Update authenticated capsules documentation
UEFI:
* Add support for loading FIT images including initrd
- efi_loader: efi_load_initrd: provide a memory mapped initrd
- efi_loader: binary_run: register an initrd
- bootm: add support for initrd in do_bootm_efi
* efi_selftest: remove un-needed NULL checks
* efi: Fix efiboot for payloads loaded from memory
* Print extra information from the bootmgr
* Move public cert for capsules to .rodata
* Set EFI capsule dfu_alt_info env explicitly
* Make FDT extra space configurable
* Install the ACPI table from the bloblist
* Handle GD_FLG_SKIP_RELOC
* Handle malloc() errors
Others:
* acpi: select CONFIG_BLOBLIST
* smbios: select CONFIG_BLOBLIST
* xilinx: dfu: Fill directly update_info.dfu_string
* cmd: fwu: Dump custom fields from mdata structure
* board: remove capsule update support in set_dfu_alt_info()
commit ddf67daac3 ("efi_capsule: Move signature from DTB to .rodata")
was reverted in
commit 47a25e81d3 ("Revert "efi_capsule: Move signature from DTB to .rodata"")
because that's what U-Boot was usually doing -- using the DT to store
configuration and data. Some of the discussions can be found here [0].
(Ab)using the device tree to store random data isn't ideal though.
On top of that with new features introduced over the years, keeping
the certificates in the DT has proven to be problematic.
One of the reasons is that platforms might send U-Boot a DTB
from the previous stage loader using a transfer list which won't contain
the signatures since other loaders are not aware of internal
U-Boot ABIs. On top of that QEMU creates the DTB on the fly, so adding
the capsule certificate there does not work and requires users to dump
it and re-create it injecting the public keys.
Now that we have proper memory permissions for arm64, move the certificate
to .rodata and read it from there.
[0] https://lore.kernel.org/u-boot/CAPnjgZ2uM=n8Qo-a=DUkx5VW5Bzp5Xy8=Wgmrw8ESqUBK00YJQ@mail.gmail.com/
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Jonathan Humphreys <j-humphreys@ti.com> # on TI sk-am62p-lp
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on AML-A311D-CC
Tested-by: Raymond Mao <raymond.mao@linaro.org>
U-Boot can pass an initrd to subsequent boot stages via the
EFI_LOAD_FILE2_PROTOCOL. The current implementation only supports
this functionality via the efi boot manager: the initrd is taken
from the load options of the BootCurrent variable. This commit adds
support for registering a memory mapped initrd, e.g. loaded from a
FIT image. For now this new method takes precedence over loading the
initrd from the BootCurrent variable (if both are present) because
the BootCurrent variable is not cleared on exiting the boot manager.
Signed-off-by: Adriano Cordova <adriano.cordova@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Current mmc bootpart-resize command only support Samsung eMMC BOOT/RPMB
hardware partition resizing. Add Sandisk and Micron eMMC BOOT/RPMB hardware
partition resizing support. The commands and parameters for resizing
partitions are different for each manufacturer. Select the corresponding
function according to CID.
Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Simplify 90cc07fd78 ("mmc: Poll CD in case cyclic framework is enabled")
according to suggestions by Rasmus. The struct cyclic_info is zero-size in
case CONFIG_CYCLIC is not enabled and does not add any size to struct mmc,
so it can unconditionally be part of that structure. This allows clean up
of all the other conditionals in mmc.c which can now be unconditionally
present, as they also add no extra space.
Suggested-by: Rasmus Villemoes <ravi@prevas.dk>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
UFS devices uses the block and scsi frameworks. Enable UFS erase
support by adding erase support to SCSI.
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
It is very surprising that such an uclass, specifically designed to
handle resources that may be shared by different devices, is not keeping
the count of the number of times a power domain has been
enabled/disabled to avoid shutting it down unexpectedly or disabling it
several times.
Doing this causes troubles on eg. i.MX8MP because disabling power
domains can be done in recursive loops were the same power domain
disabled up to 4 times in a row. PGCs seem to have tight FSM internal
timings to respect and it is easy to produce a race condition that puts
the power domains in an unstable state, leading to ADB400 errors and
later crashes in Linux.
CI tests using power domains are slightly updated to make sure the count
of on/off calls is even and the results match what we *now* expect.
As we do not want to break existing users while stile getting
interesting error codes, the implementation is split between:
- a low-level helper reporting error codes if the requested transition
could not be operated,
- a higher-level helper ignoring the "non error" codes, like EALREADY and
EBUSY.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There are already several helpers to find a udevice based on its
position in a device tree, like getting a child or a node pointed by a
phandle, but there was no support for graph endpoints, which are very
common in display pipelines.
Add a new helper, named uclass_get_device_by_endpoint() which enters the
child graph reprensentation, looks for a specific port, then follows the
remote endpoint, and finally retrieves the first parent of the given
uclass_id.
This is a very handy and straightforward way to get a bridge or a panel
handle.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Note that this undoes the changes of commit cf6d4535cc ("x86:
emulation: Disable bloblist for now") as that was intended only for the
release due to time.
This change aligns the preprocessor directive with the standard
configuration flag used for detecting 64-bit x86 architecture.
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Harsha Vardhan V M <h-vm@ti.com> says:
This patch series introduces the fuse writebuff sub-system command and
makes improvements to the existing fuse implementation by removing the
custom string functions. The patches are required to be applied in
sequence.
The series consists of the following changes:
Patch 1 removes custom string functions and replaces them with standard
string functions.
Patch 2 introduces fuse.rst documentation for fuse commands.
Patch 3 introduces the fuse writebuff sub-system command, allowing to
write a structured buffer in memory to fuses, and implementing the
necessary function calls.
Patch 4 enables the fuse sub-system in the K3 platform.
Patch 5 updates the fuse.rst documentation to include details about the
new fuse writebuff command.
These changes aim to improve the fuse sub-system by the removal of
custom string functions and the addition of the fuse writebuff
command improves fuse programming workflows by allowing to write a
structured buffer in memory to efuses.
Link: https://lore.kernel.org/r/20250319084714.335777-1-h-vm@ti.com
Add CMD_FUSE_WRITEBUFF config option to add and enable fuse writebuff
sub-system command. Add fuse_writebuff function to be invoked on
writebuff command.
Signed-off-by: Harsha Vardhan V M <h-vm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass <sjg@chromium.org> says:
The membuff implementation curently has no tests. It also assumes that
head and tail can never correspond unless the buffer is empty.
This series provides a compile-time flag to support a 'full' flag. It
also adds some tests of the main routines.
The data structure is also renamed to membuf which fits better with
U-Boot.
There may be some cases in the code which could be optimised a little,
but the implementation is functional.
Link: https://lore.kernel.org/r/20250318152059.1464369-1-sjg@chromium.org
