Dedicated MIPI calibration driver is used on T114 and newer. Before
T114 MIPI calibration registers were part of VI and CSI.
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Nvidia Tegratab T114
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
The goal of panel_set_backlight() is to enable backlight. Hence,
it should be called at the probe end.
Signed-off-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
If DISP1 is a PLLD/D2 child, it cannot go over 370MHz. The cause
of this is not quite clear. This can be overcomed by further
halving the PLLD/D2 if the target parent rate is over 800MHz.
This way DISP1 and DSI clocks will have the same frequency. The
shift divider in this case has to be calculated from the
original PLLD/D2 frequency and is passed from the DSI driver.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS Grouper E1565
Tested-by: Ion Agorria <ion@agorria.com> # HTC One X
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Nvidia Tegratab T114
Tested-by: Jonas Schwöbel <jonasschwoebel@yahoo.de> # Microsoft Surface 2
Signed-off-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Add powergate use on T114 to complete resetting of DC.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
T30+ SOC have second PLLD - PLLD2 which can be actively used by
DC and act as main DISP1/2 clock parent.
Tested-by: Agneli <poczt@protonmail.ch> # Toshiba AC100 T20
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS Grouper E1565
Tested-by: Ion Agorria <ion@agorria.com> # HTC One X
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Nvidia Tegratab T114
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tegra SoC has 2 independent display controllers called DC_A and
DC_B, they are handled differently by internal video devices like
DSI and HDMI controllers so it is important for last to know
which display controller is used to properly set up registers.
To achieve this, a pipe field was added to pdata to pass display
controller id to internal Tegra SoC devices.
Tested-by: Agneli <poczt@protonmail.ch> # Toshiba AC100 T20
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS Grouper E1565
Tested-by: Ion Agorria <ion@agorria.com> # HTC One X
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Nvidia Tegratab T114
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Consolidate HD headers and place the result into video/tegra20
since it is used only by devices from this directory.
Tested-by: Agneli <poczt@protonmail.ch> # Toshiba AC100 T20
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS Grouper E1565
Tested-by: Ion Agorria <ion@agorria.com> # HTC One X
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Nvidia Tegratab T114
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Subtracting 1 from x and y fixes image shifting on rotated
panels.
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS Grouper E1565
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Diverge DC driver setup to better fit each of supported generations
of Tegra SOC.
Tested-by: Agneli <poczt@protonmail.ch> # Toshiba AC100 T20
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS Grouper E1565
Tested-by: Ion Agorria <ion@agorria.com> # HTC One X
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Nvidia Tegratab T114
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
GCC-14 find more warnings like
"make pointer from integer without a cast"
fix them by adding a type cast.
Signed-off-by: Khem Raj <raj.khem@gmail.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Model: Firefly roc-rk3328-cc
DRAM: 1 GiB (effective 1022 MiB)
Video device 'vop@ff370000' cannot allocate frame buffer memory -ensure the device is set up before relocation
Error binding driver 'rockchip_rk3328_vop': -28
Some drivers failed to bind
initcall sequence 000000003ffcd5e8 failed at call 000000000021a5c4 (err=-28)
### ERROR ### Please RESET the board ###
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Unlike RK3399, RK3288 the Newer Rockchip SoC's like RK3328 have
different offsets for dsp registers.
Group the dsp register set via dsp_regs pointers so that dsp_offset
would point the dsp_regs to access for any changes in the offset value.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Unlike RK3399, RK3288 the Newer Rockchip SoC's like RK3328 have
different offsets for win registers.
Group the win register set via win_regs pointers so that win_offset
would point the win_regs to access for any changes in the offset value.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Get the regs from priv pointer instead of passing it an argument.
This would simplify the code and better readability.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
HPD detection on some DW HDMI designed SoC's would need to read and
setup the HPD status explicitly.
So, extend the HPD detection code by adding the dw_hdmi_detect_hpd
function and move the default detection code caller there.
The new read and setup hdp will integrate the same function in
later patches.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
DW HDMI support Vendor PHY like Rockchip RK3328 Inno HDMI PHY.
Extend the vendor phy handling by adding platform phy hooks.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
HDP is a hardware connector event, so detect the same once the
controller and attached PHY initialization are done.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Support timing parsing from EDID if panel device tree node
provides DDC i2c bus instead of timings node.
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF201
Tested-by: Agneli <poczt@protonmail.ch> # Toshiba AC100 T20
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
[agust: reworked to fix dm_i2c_* build errors and to big img size]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
MP1:
_ Add OHCI HCD support for STM32MP15xx DHSOM
_ Report OTP-CLOSED instead of rev.? on closed STM32MP15xx
_ Initialize TAMP_SMCR BKP..PROT fields on STM32MP15xx
_ Jump to ep on successful resume in PSCI suspend code
_ Add FASTBOOT support for STM32MP13
_ Fix/Rework key and leds management for STM32MP13/15
_ net: dwc_eth_qos: Clean up STM32 glue code and add STM32MP13xx support
MP2:
_ Add stm32-fmc-ebi support
_ Add: sdmmc2 support and fix AARCH64 compilation
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use led node's name instead for
u-boot,error-led property.
Rename red led node's name to led-red.
Remove status property which is useless.
Add compatible = "gpio-leds"; which is not present in kernel DT.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
red led and button dedicated to fastboot share the same gpio GPIOA13.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from red led node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use led node's name instead for
u-boot,error-led property.
Rename red led node's name to led-red.
Remove status property which is useless.
Add compatible = "gpio-leds" which is not present in kernel DT.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
red led and button dedicated to fastboot share the same gpio GPIOA13.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from red led node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use blue led node's name instead
for u-boot,boot-led property.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use red led node's name instead
for u-boot,error-led property.
Rename red led node's name to led-red.
Remove status property which is useless.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
red led and button dedicated to fastboot share the same gpio GPIOA13.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from red led node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use blue led node's name instead
for u-boot,boot-led property.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use red led node's name instead
for u-boot,error-led property.
Rename "red" led node's name to "led-red".
Remove status property which is useless.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
red led and button dedicated to fastboot share the same gpio GPIOA13.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from red led node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
